Panasonic Document Scanner Kv S5076h_s5046h Operating Manual

							1.Prepare the following cleaning supplies.
• Soft and dry cloth
Used to clean the conveyor.
• Thin cotton swab
Used to clean the ion outlets and sensors.
• Roller cleaning paper (KV-SS03)
Used to clean the rollers, scanning backgrounds, and scanning glasses.
Use of the roller cleaning paper is recommended. If you do not have the roller cleaning paper, use a
soft cloth with a small amount of isopropyl alcohol or water.
Do not use commercially available cleaners, detergent, thinner, or benzine. (Doing so may cause
deformation, discoloration or damage.)
2. Press and hold the power button for one second or more to turn off the unit’s power.
3. Push the ADF door release ( A) upwards, and open the ADF door ( B).
4. Clean the conveyor, sensors, rollers, scanning backgrounds, and scanning glasses.
• Clean the parts in the following order: conveyor, ion outlets and sensors, rollers, scanning backgrounds,
scanning glasses.
• For details about cleaning, refer to the following:
– "Cleaning the Conveyor" (page 53)
– "Cleaning the Ion Outlets and Sensors" (page 54)
– "Cleaning the Rollers" (page 56)
– "Cleaning the Scanning Backgrounds" (page 58)
– "Cleaning the Scanning Glasses" (page 59)
Operating Manual51
Care and Maintenance12  
						

							5.Close the ADF door.
• After cleaning, push both sides of the ADF door down slowly until it clicks into place.
6.Press the power button to turn on the unit’s power.
Notice
•If roller cleaning notifications via the After Clean Roller Counter are enabled, after turning on the
unit’s power, reset the After Clean Roller Counter in User Utility to 0.
For details, refer to the User Utility help.
52Operating Manual
Care and Maintenance  
						

							Cleaning the Conveyor1.With a soft and dry cloth, wipe off any dirt on the conveyor ( A).
2. With a soft and dry cloth, wipe off any dirt on the self-cleaning brushes ( C, D ) of the reference plates
( A , B ).
• Push  E and  F in the direction indicated by the arrow to rotate the reference plate on the ADF door
side so that you can clean the brush. In the same way, push  G and  H in the direction indicated by the
arrow to rotate the reference plate on the main unit side to clean the brush.
Operating Manual53
Care and Maintenance1 56
78
3
4
1
2  
						

							Cleaning the Ion Outlets and Sensors1.Remove dust from the ion outlets ( A) with a cotton swab.
• With a thin cotton swab, remove dust from the ion outlets, and then wipe the center of the inner parts
approximately 5 times.
Notice
•Do not apply too much pressure on the parts.
2. Remove dust from the sensors ( A, B , C , D , E , F ) and reflectors ( G) with a cotton swab.
Location of Sensors
AWaiting sensorBDouble feed detectorCSlip detect sensorDStarting sensorEPaper sensorFSkew sensor54Operating Manual
Care and Maintenance1 1
2
2
3
4
5
6  
						

							Location of ReflectorsGReflectors Operating Manual55
Care and Maintenance7 7  
						

							Cleaning the Rollers1.Use the roller cleaning paper (page 50) to remove the dirt from the surfaces of all rollers.
Direction to wipe rollersDouble feed prevention roller, Separation rollerOther rollers
Notice •After removing the double feed prevention roller, gently wipe dirt from the surface of the roller in
the direction indicated by the arrows in the illustration. If you wipe too hard, you may damage or
misalign the roller.
For instructions on how to remove the double feed prevention roller, see "Replacing the
Rollers" (page 61).
• Wipe dirt off of the other rollers in the directions indicated by the arrows in the illustration. Use your
finger to rotate the roller and wipe dirt off of the entire surface of the roller. If the roller rotates when
wiping it, gently hold it in place with your finger.
56Operating Manual
Care and Maintenance   
						

							Location of RollersAPaper feed rollerBSeparation rollerCFree rollersDDouble feed prevention rollerEDrive rollers  Operating Manual57
Care and Maintenance3
4
12 5  
						

							Cleaning the Scanning Backgrounds1.Wipe the scanning backgrounds ( C, D ) on each reference plate ( A, B ) with the roller cleaning paper
(page 50).
• Push  E and  F in the direction indicated by the arrow to rotate the reference plate on the ADF door
side. Clean both the white and black backgrounds. In the same way, push  G and  H in the direction
indicated by the arrow to rotate the reference plate on the main unit side to clean the white and black
backgrounds.58Operating Manual
Care and Maintenance56
78
3
4
1
2  
						

							Cleaning the Scanning Glasses1.Wipe the scanning glasses ( A, B ) with the roller cleaning paper (page 50).
Location of Scanning GlassesAScanning glass (F)BScanning glass (B)Operating Manual59
Care and Maintenance1 2  
						

							Consumables and Optional Accessories Part NamePart NumberNotes
Consumables
Roller exchange kit
• Paper feed roller
module
• Double feed prevention
roller
KV-SS060—
Roller cleaning paperKV-SS03See "About the roller cleaning
paper" (page 50).
Ink cartridgeKV-SS021
For optional imprinter unit.
For instructions on installation and
removal, see "Installing the
Imprinter Unit and Ink Cartridge" 
(page 67).
Optional
AccessoriesImprinter unitKV-SS014
Prints text and numbers on
documents. Includes 1 ink
cartridge.
For instructions on installation, see
" Installing the Imprinter Unit and Ink
Cartridge" (page 67).
Note
•To purchase separately sold items, contact your dealer.
When to replace the rollers As a rough guideline, we recommend to replace the paper feed roller module and double feed prevention roller
after scanning 350,000 sheets of paper.  ("350,000 sheets " is based on scanning normal paper. Depending on
the type of paper and other factors, the actual lifetime for the rollers will differ.)
In User Utility, you can check the number of sheets that have been scanned.
60Operating ManualC
o
n
s
u
m
a
b
l
e
s
a
n
d
O
p
t
i
o
n
a
l
A
c
c
e
s
s
o
r
i
e
s
Consumables and Optional Accessories