Panasonic DP 3530 User Manual

							31
Before Starting
DP-6030
1089
1234567
Contents
COPY Key
● To use the unit as a photocopier.
ENERGY SAVER Key
● Saves power while the copier is not in use.
INTERRUPT Key
● Interrupts other copy or print jobs while making copies.
FUNCTION Key
● Use when changing the paper size, initial function values (default values) and key operator settings.
RESET Key
● Resets all features to the initial power-on state.
CLEAR Key
● Clears the copy count in the display.
STOP Key
● Stops the copy run.
STATUS LED (RED)
● Flashes when trouble occurs.∗∗
ACTIVE LED (GREEN)
● Lights when machine is active.
PRINT DATA LED (GREEN)
● Lights when receiving print data.
ORIGINAL
SIZE KeysCOPY SIZE
KeysTouch Panel
DisplayKeypad START
Key
∗∗When the machine detects a problem or an alarm status is activated, the  8  Alarm LED lights
or begins to flash.
LED Lights: Machine detected a trouble status
  •  No paper in the selected tray or toner has run out.
  •  Machine detected trouble, such as paper misfed or jammed.
LED Flashes: Machine detected an alarm status
  •  No paper in the Tray. (Tray not selected)
  •  Toner is getting low, etc.
●The Control Panel displayed above shows only copier functions. Please refer to the
appropriate operating instructions for other control panel functions.
∗Fax/Email ON LINE LED for optional Fax/Internet Fax functions
Print ON LINE LED for Printer function
No.
1
2
3
4
5
6
7
8
9
10
NOTE
Control Panel
Downloaded From ManualsPrinter.com Manuals 
						

							32
Before Starting
To uch Panel Display
DP-6030
12345910
202221
12
15
16
18
19
26
25
24
23
27
13
14
118
67
17
NOTE●Use only gentle finger pressure to activate the Touch Panel Display. DO NOT USE SHARP
OBJECTS such as pens, fingernails etc., as this may damage the panel.
●Touch Panel Display Brightness Adjustment:
To adjust the brightness of the Touch Panel display, press and while holding down the  C
(CLEAR) key, keep pressing the  ORIGINAL SIZE/LEDGER or the  COPY SIZE/LEDGER
keys until the desired brightness is achieved.
ORIGINAL SIZE/LEDGER : Dimmer
COPY SIZE/LEDGER        : BrighterJob Status Indicator
Ex.: Copying 3 sets.
The Indicator displays the progress of a job task as follows:
0/3 → 1/3 → 2/3 → 3/3
When the Department Counter function is set up, the departmental
Identification Code input screen is displayed on the Touch Panel
Display. A registered departmental Identification Code (4-digit) is
required to gain access to each secured function, or the secured
Copy/Fax/Scanner function(s) cannot be used. Please consult
with the key operator regarding the departmental Identification
Code(s) for the desired function.
Downloaded From ManualsPrinter.com Manuals 
						

							33
Before Starting
Contents See Page
Warning Indications14 - 17
      : Add Toner        : Add Paper     : Call Service (Call your Service Provider)      : Waste Toner
Original Icon—
Original Size Indication—
Multi-Size Feeding / Job Build and SADF Mode Indication 46 and 47
Rotate Mode Indication—
Number of Copies / Original(s) —
Machine / User Error Code Indication (E1-01, U13, etc.) 21 and 86
Copy Icon—
Copy Size Indication—
Reserve a Job Button63
Finisher Functions Indication49
Machine Outline with Tray Selection (Paper Tray and Output Tray) —
Paper Level and Size Indication —
Paper Tray Selection Button—
Tandem/Remote Button Indication 37
Tandem/Remote Button37
Density Indicator (7 steps) 15, 35, 85
Manual Exposure Select Buttons (Lighter and Darker) 15, 35, 85
Original Mode Select Button (Text; Text / Photo; Photo) 15, 35, 85
Copy Image and Paper Image Indication —
Copy Ratio Indication—
Original Image Indication—
Completion Notice Button41
Job Queue Button40
Job Settings Button—
•Selected copy jobs will be indicated on the right side of the touch panel display.
(2-Sided/Original → Copy, Sort/Finish, Zoom/Effects, Insertion/Overlay modes)
Proof Set Button37
Function Categories—
■ Touch Panel Display Indications
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Downloaded From ManualsPrinter.com Manuals 
						

							34
Making Copies
Basic Menu
■ Copying the Same Size Originals (1:1)
Copy size is automatically selected.
100%
If set in other
function mode or
If original size
is not detected
NOTE●During the copy operation and after making copies, the fan motor may start spinning. This is a
normal operation and is used to cool down the copier.
12
■ Positioning Original(s)
On the i-ADF On the Platen
■ Using the ADF
 Originals that cannot be used
●Post Cards,  Drawing Papers, Transparencies,
Labelling Papers, Heavyweight Papers, Thin Art
Papers,  Film Thermal Papers
Inappropriate Originals
●Paper with a smooth surface such as glossy and
coated papers
●Originals with a Lead Edge that is ripped, creased,
folded, punched, or glued.
●Mixed width size Originals (except a combination of
Ledger and Letter)
●Paste-ups
●Pressure sensitive or carbon backed papers
●Paper with excessive curl
●Stapled originals
●Freshly printed copies from a laser printer
●Originals with fresh White-Out (Liquid paper
correction fluid)ADF
Upper Limit
Indicator
Upper Limit Guide
Note 1)Once after setting originals , pressing Start button, do not press originals as it may cause original jam.
Note 2)When originals with clipped or stapled,  take off clips or staples, then set originals neat.
Set the originals up to the
upper limit indicator/Guide.
ADF Tray
Original Guides
Adjust to the original’s width
Downloaded From ManualsPrinter.com Manuals 
						

							35
Making Copies
Adjust the Manual Exposure
  or  
Select type of Original(s)
Mainly Text
Text and Photo
combined
Mainly Photo
Number of Copies
(Max. 999)
NOTE●Memory Capacity:
If memory overflows during original scanning, the message  “Cannot Complete / Job
Exceeds Memory Capacity” will be displayed on the LCD. If this occurs, follow the instructions
on the LCD.
When additional memory is required, consult with an authorized service provider.
■ Copying on Heavy Paper (Post Cards, etc.) (35 lb max.)
Load paper
on the Sheet
Bypass
Select Sheet Bypass and
touch the Size Change button
3
4
Select Heavy Paper
34
123
4
When copying a thick Booklet, open the ADF and verify that the ADF Hinge was returned to original position if the
rear of the ADF was raised.
Downloaded From ManualsPrinter.com Manuals 
						

							36
Making Copies
Basic Menu
100
copies
50
copies50
copies
+
100 copies
2 1100
■ Copying with Preset Ratios (Reduction/Enlargement)
Letter
Ledger LetterLedger oror
If original size
is not detected
■ Proof Copying
or
Allows you to make one proof set, before
proceeding to copy a large multi-set with
various settings.
Proof copy
Multi copy
Select Copy Job settings
■ Tandem/Remote Copying
or
Requires installation of optional Hard Disk Drive (DA-
HD60), Network setup (See pages 71, 78 and 79)
and Parameter registration. (See pages 38 and 39)
Select Copy Job settings
Remote Copying
Tandem Copying
Other copier Other copier
This copier
Stationor
NOTE●If the desired copy size is different from the paper size loaded in the Paper Tray, use Sheet
Bypass. (See page 14)
The selected Remote printing copier, must be either DP-3510 / 3520 / 3530 / 4510 / 4520 /
4530 / 6010 / 6020 / 6030.
For the copier to function as a Remote/Tandem Copier it has to be setup in advance.
12
12
12
5
Downloaded From ManualsPrinter.com Manuals 
						

							37
Making Copies
ORIGINALCOPY SIZE
SIZE Ledger Legal Letter-RInvoice-R
Ledger 100 77 65 50
Legal 121 100 79 61
Letter-R 129 100 100 65
Invoice-R200 155 129 100 The Correct ratio is automatically selected.
Reduction and enlargement ratios (%)
DP-6030
Number of Copies
(Max. 999)
DP-6030
Number of Copies
(Max. 999)
If the Proof copy is OK,
the remaining number
of sets will be printed.
If the Proof Copy is NG,
again, place the originals
back on the ADF (or
Platen) and try again. or
DP-6030
Number of Copies
(Max. 999)
DP-6030
NOTE●Press the PROOF SET button again if the Proof Copying mode was reset.
34
345
34
5
67For Tandem
For Remote
Downloaded From ManualsPrinter.com Manuals 
						

							38
Making Copies
Basic Menu
■ Tandem/Remote Copy Settings (Registration 1)
Input the Key Operator ID Code if required.DP-6030
DP-6030
Input ID Code
(4-digit)
Enter the key name∗
(up to 15 characters).
∗By default, the key name will
be up to 15 characters of the
station’s name.
■ Tandem/Remote Copy Settings (Registration 2)
If installing the machine on a Network
with a different subnet mask, you must
first register it before being able to use
the Tandem/Remote Copying function.DP-6030
Scroll to
05/05
30IP Address∗
Ex: 123.123.12.1
When entering a 1 or 2-digit number
segment, add “00” or “0” in front of the
number, to scroll to the next segment of
numbers or press the “
“ key to enter a
period after the number.
■ Tandem/Remote Copy Settings (Editing)
To edit the registered machine’s settings
(IP Address, machine name or key name).Open the screen
05/05 same as
the Registration
procedures above.
■ Tandem/Remote Copy Settings (Deleting)
To delete the registered machine.Open the screen
05/05, same as
the Registration
procedures above.
1
4
7
12
56
12
12
Downloaded From ManualsPrinter.com Manuals 
						

							39
Making Copies
Scroll to 08/10
To input upper case letter(s).
To input numbers and/or symbols.To move the cursor (_) to the left or right side.
To erase the character before the cursor. Machine name
(up to 15 characters)
Button Names on the QWERTY Keyboard
Input ID Code
(4-digit)Scroll to
05/05
Enter the machine and key
name, same as the Registration
procedures above.
Select the registered
machine name
Enter the new IP Address,
same as the Registration
procedures above.Enter the machine and key
name, same as the
Registration procedures
above.
Select the registered
machine name
23
4
56
7
34
5
7
345
34
8
∗When clearing the IP address, press the  key to move to the next segment
of the IP address (
∗∗∗.∗∗∗.∗∗∗.∗∗∗) and press the Clear key.
Downloaded From ManualsPrinter.com Manuals 
						

							40
Making Copies
Basic Menu
■ Job Queue
Refers to a list of jobs waiting to print, delete
or change of priority (only for print job).
Job
 1
Job
 2
Job
 3
Job 3
Job 1
Job 2
Deleted
Select the job(s)∗
you wish to delete
∗∗
∗You can select to delete multiple/all jobs.
∗∗Priority can be selected for print jobs only
when the optional HDD is installed. Select the job(s)
■ Completion Notice
A Job Completion Notice via a pop up screen on the
Desktop of your PC when the Copy Job is
completed.
Before using the Completion Notice, install the
Panasonic-DMS included with the machine.
Copy is completed.
Pop up screenSelect Pop up
Display
Right click the
Status Monitor icon
or
NOTE●The PRINT JOB QUEUE requires the Key Operator’s Password, however, the COPY JOB
QUEUE does not require a password.
The Job Queue selection function is only available when the optional HDD is installed.
1
4
12
Downloaded From ManualsPrinter.com Manuals