Panasonic Eyfma1p Operating Instructions Manual

Operating Instructions
Instructions d’utilisation
Manual de instrucciones
Cordless Impact Driver/Cordless Impact Wrench
Perceuse à impact sans fil/Clé de serrage à impact sans fil
Destornillador de impacto inalámbrico/Llave de impacto inalámbrica\
Model No: EYFLA4A / EYFLA4AR EYFLA5A / EYFLA5AREYFLA5Q / EYFLA5QREYFLA6J / EYFLA6JR
EYFLA6P / EYFLA6PR
EYFMA1P 
EYFMA1J 
IMPORTANTThis manual contains safety information. Read manual completely before f\
irst using this product and save this 
manual for future...

-  - 
Index
English: Page  4
Français:  Page
   0
Español:  Página  38
FUNCTIONAL DESCRIPTION
DESCRIPTION DES FONCTIONS
DESCRIPCIÓN FUNCIONAL
Remote control and battery are not included.
La télécommande et la batterie ne sont pas incluses.
El control remoto y la batería no están incluídos.
(G)(H)
(I)
(N)
(O)
(P)
(M)
(Q)
(V)
(U)
(R)(T)
(S)
(B)
(A)
(C)
(D) (E) (F)
(J)
(K)
EYFLA4A/EYFLA4AR
EYFLA5A/EYFLA5AR
EYFLA6P
EYFLA6PR
EYFMA1PEYFLA5QR
EYFLA5Q
EYFLA6J
EYFLA6JR
EYFMA1J
(L) 

- 3 -  
(A)
6.35 mm - (EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/square drive (EYFLA5Q\
, EYFLA5QR, EYFLA6J, 
EYFLA6JR, EYFMA1J/pin type EYFLA6P, EYFLA6PR, EYFMA1P/pin-detent type)
6,35 mm - 
(EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/entraînement carré (EYFLA\
5Q, EYFLA5QR, EYFLA6J, 
EYFLA6JR, EYFMA1J/type à goujon EYFLA6P, EYFLA6PR, EYFMA1P/type à goupille d'arrêt)
6,35 mm - (EYFLA4A, EYFLA4AR/EYFLA5A, EYFLA5AR)/excitador cuadrado (EYFLA5Q, EY\
FLA5QR, EYFLA6J, 
EYFLA6JR, EYFMA1J/tipo pasador EYFLA6P,...

- 4 - 
I. GENERAL SAFETY 
RULES
 WARNING! Read all instructions
Failure  to  follow  all  instructions  listed 
below  may  result  in  electric  shock,  fire 
and/or  serious  injury.  The  term  “power 
tool”  in  all  of  the  warnings  listed  below 
refers  to  your  mains  operated  (corded) 
p o w e r   t o o l   a n d   b a t t e r y   o p e r a t e d 
(cordless) power tool.
SAVE THESE INSTRUCTIONS
Work Area Safety
1)  Keep work area clean and well lit.Cluttered or dark areas invite accidents....

- 5 -  
the  power  tool  before  making  any 
adjustments,  changing  accessories, 
or storing power tools. 
S u c h   p r e v e n t i v e   s a f e t y   m e a s u r e s 
reduce the risk of starting the power tool 
accidentally.
4)

 
Store idle power tools out of the reach 
of  children  and  do  not  allow  persons 
unfamiliar with the power tool or these 
instructions to operate the power tool.
Power tools are dangerous in the hands 
of untrained users.
5)
  M a i n t a i n   p o w e r   t o o l s ....

- 6 - 
7) Do not strain the tool by holding the speed 
c o n t r o l   t r i g g e r   h a l f w a y   ( s p e e d   c o n t r o l 
mode) so that the motor stops.
Symbol  Meaning
VVolts
Direct current
n0No load speed
… min-1Revolutions or reciprocations 
per minutes
AhElectrical capacity of battery  pack
IV.	ASSEMBLY
Attaching or Removing Bit
NOTE:
• When  attaching  or  removing  a  bit,  discon-
nect  battery  pack  from  tool  or  place  the 
switch in the center position (switch lock).
1. Hold the...

- 7 -  
Attaching Socket (Pin­detent)
1  Depress the pin-detent on the square drive.
2  Attach the socket to square drive.
3  M
ake  sure  the  socket  is  securely  attached  to 
the square drive.
Removing Socket (Pin ­detent)
1  Insert a small rod into the hole on the socket.
2 
Depress the pin-detent, then detach the socket.
NOTE: Keep the temperature of the tool above the 
f reezing  point  (0°C/3 °F)  when  attaching 
sockets  to  or  removing  them  from  the 
square  drive.  Do  not  use...

- 8 - 
. To remove the battery pack:
Push up on the button from the front to re-
lease the battery pack.
Button
V.	OPERATION
Before  Using  the  Remote 
Control  (Available  as  an 
optional accessory)
Insert the battery
1.  Pull out the battery holder.
1  P
ush  in  on  the  fas-
tener  as  indicated  by 
the arrow.
2  Pull out the holder
 .
.  Insert the battery and 
push  the  holder 
back in.
NOTE:
•
  If  the  tool  does  not  respond  to  the  wire -
less remote control even when the...

- 9 -  
Forward  Rotation  Switch 
Operation
1. Push the lever for forward rotation.
.  Depress  the  trigger  switch  slightly  to  start 
the tool slowly.
3.

  The  speed  increases  with  the  amount  of 
depression  of  the  trigger  for  efficient  tight-
ening  of  screws.  The  brake  operates  and 
the  bit  stops  immediately  when  the  trigger 
is released.
4.

  After  use,  set  the  lever  to  its  center  posi -
tion (switch lock).
Reverse  Rotation  Switch 
Operation
1. Push the...

- 10 - 
(2) The battery indication lamp
• Use  the  battery  indication  lamp  to  check 
how much power is left in the battery.
•
  Battery  life  varies  slightly  with  ambient  tem-
perature  and  battery  characteristics.  The 
lamp  is  designed  to  provide  a  rough  indica-
tion of remaining battery life.
 
Battery indication lamp
Indicator Battery status
Fully charged
Approx. 40% or less 
remaining
Flashing
Flashing 
Approx. 0% or less 
remaining (indicates need 
to recharge battery)
The...