Panasonic High Speed Scanner Kvs2065l Operating Instructions

							11
Precautions
³³ ³ ³
Power Source
•
Use a voltage level that does not vary more than d10% from the voltage level marked on the nameplate
(located on the back side of the scanner).
•Do not use an extension cord.
•This scanner should be connected to a grounded outlet.
•Do not use a line conditioner, transient suppressor or surge protector.
ºº º ºCD-ROM
To prevent the CD-ROMs from accidental damages: Do not place the unit near a heating appliance or an air
conditioning vent. Do not place the unit in a room with
extremely high or low humidity.Do not place the unit near other appliances which
generate large electrical noise.
Do not place the unit on a carpet. (Static electricity can
cause the unit to malfunction.)Do not drink or inhale the included roller cleaning paper
fluid.
The roller cleaning paper may be harmful to sensitive
skin, so please use protective gloves. 
Do not use the roller cleaning paper near a heater or
open flame. This may cause a fire.
Do not touch or write on the surface
of the disc.Do not leave the disc out of the
protective case.Do not leave the disc in direct
sunlight or near heat sources.
Do not place heavy objects on the
disc case or drop the case.To clean the disc, hold the disc by
its edges and wipe it from the
center to the edges with a dry, soft
cloth. 
						

							12
Component Identification
  Exit substopper
Exit extension tray
Exit stopper
Document guide 
Hopper extension 
tray
Hopper
Front door release
Inside the front door.
Exit document 
guide
Power indicator
When the power is 
turned on, the green 
indicator lights. 
When an error occurs, 
the  indicator will 
change to red, and 
light steadily or flash.
Power switch
 [: on position
²: off position
Display panel
When performing 
each setting, used to 
display the scanning 
conditions, etc. 
Front door
ADF / manual feed 
selector
To prevent double feeding, 
adjust the selector to feed 
the scanning document 
properly. 
(Refer to page 33.)
Connectors
Used to connect the  
scanner unit to the 
host computer.
AC inlet
Power cord
Fan exhaust ventPaper path selector
Used to change the 
scanning document’s path 
direction (front side/back 
side). 
(Refer to page 33.)
Pre-imprinter door  
(Top door)
Used for attaching the 
imprinter unit and ink 
cartridge. 
An imprinter unit installed 
here is called a pre-
imprinter.
Post-imprinter door (Back door)
Used for attaching the imprinter unit and ink 
cartridge.
An imprinter unit installed here is called a post-
imprinter. 
						

							13
Display Panel Instructions
The required settings must be selected prior to scanning.
Information and conditions are shown on the LCD (Liquid Crystal Display).
ºº º ºDisplay panel and keys
Ready
: Press to enter the scanning setting menu.
: Press to enter the counter setting menu.
: Press to enter the imprinter setting menu.
: Press to enter another setting menu.
: Press to exit from the setting section and
return to the ready status. 
Also, this function can change the display
language.
: Used to start or stop scanning a document.
Up to 32 characters can be displayed during
scanning or setting.
3: Press to advance to the next mode in the
selected menu.
4: Press to return to the previous mode in the
selected menu.
1: Press to advance to the next value in the
selected mode.
2: Press to return to the previous value in the
selected mode.
STOP / STARTHOME OTHERS
IMPRINT COUNTER
SCANSELECTMODE
SCAN
COUNTER
IMPRINT
OTHERS
HOME
STOP / START
LCD: 
						

							 
14 
Display Panel Instructions 
´ 
Setting the language 
• 
Select English, German or Japanese as the language which is to appear on the LCD display. 
• 
The language setting mode is appeared automatically when the unit’s power is turned on for the first time after
the unit was purchased. English is the default language. 
1
 
Turn the power on while pressing the
HOME key.
• 
When “High Speed Scanner” or other
words appear on the LCD, release the
HOME key. 
2
 
Use the  
2
 
 key or the  
1
 
 key to select
“English L 
etter”, “English A4”,
“Deutsch A4” or   .
 
3
 
Press the HOME key.
• 
The display will change to the selected
language, then the scanner will be ready. 
• 
This setting will remain until it is changed
to another setting.
Se t L a ng ua ge
En g l i s hLe t t e r
D e u t s   c  h Se t L a ng ua geA4
Bere i tBere i t 
						

							 
15 Display Panel Instructions      ºº º º  Setting the scanner  The following parameters can be customized using the scanner’s various setting modes. If the application
software provides these features, it will be supported by the scanner.  Scan menu  No.
ItemLCD displayContentsPage
  01
Front side dropout 
colorF. Color dropColor selection for dropout when scanning the front
side of a document.
20 02 Front side brightness F. BrightnessSelection for density when scanning the front side of a
document.
03
Front side image 
emphasisF. EmphasisSelection for emphasis when scanning the front side of
a document.
04 Front side contrast F. ContrastSelection for contrast when scanning the front side of a
document.
05 Front side halftone F. HalftoneSelection for gradation when scanning the front side of
a document.
06Back side dropout 
colorB. Color dropColor selection for dropout when scanning the back
side of a document.
21 07 Back side brightness B. BrightnessSelection for density when scanning the back side of a
document.
08Back side image 
emphasisB. EmphasisSelection for emphasis when scanning the back side of
a document.
09 Back side contrast B. ContrastSelection for contrast when scanning the back side of a
document.
10 Back side halftone B. HalftoneSelection for gradation when scanning the back side of
a document.
11 Noise reduction Noise Reduct.Selection for noise reduction when scanning a
document.
12 Black line removalBLK Line 
RemoveSelection to choose to remove the black lines
appearing at the top or bottom or at the left and right
edges of the image after scanning the document.
22 13 Scanning modeScanning 
ModeSelects whether documents are scanned at actual size
or reduced (Fit to Page) size.
14Double feed 
detectionDouble FeedSelection to choose to detect double feeding function.
When scanning very important documents, confirm if
the number of scanned pages displayed on the LCD
matches the number of actual pages.
15Setting the “Double 
Feed” detector actionDouble Feed 
ActionSelects the action of the Double Feed Detector when
double feed occurs.
16
Setting the double feed 
detector sensitivityDouble FeedSelects the sensitivity of the Double Feed Detector. 
						

							 
16  Display Panel Instructions  Counter menu  No.
ItemLCD displayContentsPage
  17 Feed speed Feed SpeedSelection for feed speed when a document is being
scanned.
23 18Save settings 
(Select memory)Save Setting Selects the memory where the conditions are saved
into.
Save scanning 
settings (Execution)Save Setting Saves the scanning conditions into the memory. 
(2 memory settings)
19Load scanning 
settingLoad SettingLoads the memory where the scanning conditions have
already been saved. If “Default” is selected, all of the
scanning conditions will return to the default values.
 
No.
ItemLCD displayContentsPage  
01Select the counter 
displayed on the LCDDisp. CounterSelection to choose to display the cleared counter
(scan counter) after scanning one time or to display the
user set counter (user counter) on the LCD.
24
02Setting the User 
CounterUser Counter Selection for default number before scanning.
Setting the user 
counter extenderUser Counter Selection for an increase in the default number.
Clear the user 
counterUser Counter Clears the counter which was set by the user.
03 System CountSystem 
Count.Displays the total amount of scanned documents up to
now. 
						

							 
17 Display Panel Instructions  Imprinter menu  Depending on the setting of the “Counter setting menu”, the page number of the scanned document will be
printed. The imprinter option (KV-SS010) is required. If a host computer is connected, there may be settings
required on the host computer as well.  No.
ItemLCD displayContentsPage
  01Setting the pre-
imprinter dataPre ImprintAllows for the selection of the printing content using an 
imprinter.
The imprinter will print on the printing (front) side of the 
document scanned.
25
02Setting the pre-
imprinter positionPre PositionAllows for the selection of the printing position using a 
pre-imprinter.
03Setting the pre-
imprinter font stylePre FontAllows for the selection of the printing font style using a 
pre-imprinter.
04Setting the pre-
imprinter orientationPre RotateAllows for the selection of the printing orientation using 
a pre-imprinter.
26 11Setting the post-
imprinter dataPost ImprintAllows for the selection of the printing content using an 
imprinter.
The imprinter will print on the reverse side of the 
document scanned.
12Setting the post-
imprinter positionPost PositionAllows for the selection of the printing position using a 
post-imprinter.
13Setting the post-
imprinter font stylePost FontAllows for the selection of the printing font style using a 
post-imprinter.
14Setting the post-
imprinter orientationPost RotateAllows for the selection of the printing orientation using 
a post-imprinter. 
						

							 
18  Display Panel Instructions  Others menu  No.
ItemLCD displayContentsPage
  01 Checking the version VersionDisplays the firmware version of the mechanical
control, pre-imprinter or post-imprinter. If an optional
imprinter is not installed, the imprinter version will not
be displayed.
27 02 Setting the buzzer BuzzerSelects whether the buzzer is turned on or off. If
selection is in the “ON” position:
When pressing a key, one short beep will be heard.
When there is an error, 5 short beeps will be heard.
When scanning is completed correctly, one long beep
will be heard.
03 Setting the SCSI ID SCSI ID Sets the SCSI ID number.
04 Setting the terminator TerminatorSets “Enable” or “Disable”.
“Enable” : If last device on chain.
“Disable” : If between devices.
05Setting the transfer 
rateTransfer Rate
 
• 
Changes the maximum value of the synchronous
transfer rate of the SCSI interface. 
• 
Lower the synchronous transfer rate to 10 Mbytes/
sec. if the computer has failed to recognize the
scanner or the scanner fails to operate properly.
06Checking the roller 
cleaning warningClean RollerThe alarm tells you it is time to check the roller. If it is
near 100%, clean the roller. See “Cleaning the Unit” on
page 36.
28 Clearing the roller 
cleaning warningClean Roller Clear the “Clean Roller Warning  
²²  
%” display.
07Checking the roller 
modules replacement 
warningReplace Roll.The alarm tells you the roller needs to be changed. If it 
is near 100%, replace the paper feed roller module and 
retard roller module. See  “Replacing Consumables” on  
page 41.
Clearing the roller 
modules replacement 
warningReplace Roll.Clear the “Replace Roll. Warning  
²²  
%” display.
08Setting the product 
IDProduct IDSelects the product ID. The product ID setting depends
on the host computer scanner application you are
using. Allows scanner to emulate other Panasonic
scanners.
09Setting the sleep 
modeSleep Mode Sets the time until sleep mode turns ON. 
						

							 
19 Display Panel Instructions  ´  Operation 1  Press one of the menu key until the
desired menu is displayed. 
• 
The SCAN, COUNTER, IMPRINT and
OTHERS keys are used as a menu key. 
• 
When pressing the SCAN key, the display
will appear as shown at the right. 
2
 
Use the  
3
 
 key or the  
4
 
 key to select
the desired item.
• 
The display at the right is an example of a
setting for the scanning setting mode. 
3
 
Use the  
1
 
 key or the  
2
 
 key to select
the desired content.
• 
The display on the right is an example of
a setting for the “B. Contrast”. 
4
 
Press the HOME key to return to the
“Ready” display or another menu key
to go to another menu. 
¤ 
In steps 2 or 3, you can change to the desired menu by pressing the desired menu key. 
¤ 
See pages 20 to 28 for details. 
¤ 
For changing the display language, see page 14.
HOME OTHERS
IMPRINT COUNTER
SCANSELECTMODE
Menu keys
2
3
4 1, 4
 
01.F.Co lor drop
Ho s t
09 .B.Contrast
L
HHost
09 .B.Contrast
L
Ready
01 . D i sp .Counter
				Sc an
When the HOME key is pressed :
When the COUNTER key is pressed for another menu key :
(ex. SCAN) 
						

							20
Display Panel Instructions
´Actual settings
Scan setting menu (by pressing the SCAN key)
¥
For changing the display language, see page 14. Number, mode and default display
¥Pressing the 3 key will change to the next
mode.
¥Pressing the 4 key will change to the
previous mode.Contents
¥Pressing the 1 key or the 2 key will change to another
value.
01    Front side dropout color
Color selection
02    Front side brightness
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒNormÓ.
¥ÒDÓ means dark. ÒLÓ means light.
03    Front side image emphasis
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒMediumÓ.
04    Front side contrast
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒNormÓ.
¥ÒHÓ means high. ÒLÓ means low.
05    Front side halftone
¤
1The dynamic threshold is not displayed if the DIMM
expansion memory module has not been installed. If the
dynamic threshold is to be used, install a DIMM memory
module which is available on the market.  For details on
how to install it refer to the installation manual.
01.F.Co l
	Ho s t or dropGreen Red Host
02.F.Br ightness
DD4 D2D3 D1 Norm
HostL4 L3 L2 L1
03.F.Emp
	Ho s t hasis
None Smooth Low Medium
HostHigh
04.F.Contrast
LH	Ho s tL4 L2L3 L1 Norm
HostH4 H3 H2 H1
05.F.Ha l
	Ho s t f t one
Binary Host Bayer dither 64 Bayer dither 16
(Dynamic Threshold)
Halftone dot 32 Error diffusionHalftone dot 64

¤1