Panasonic High Speed Scanner Kvs2065l Operating Instructions

							41
Replacing Consumables
If “Warning Replace Roller” message is displayed on the LCD, replace the paper feed roller module and retard roller
module at the same time.
1Turn the power off and unplug the
power cord.
2Use your hand to pull towards you the
front door release.
Then open the front door completely.
3Place your finger on the paper feed
roller block shaft and pull it towards
you to remove the paper feed roller
block from the magnet. (1)
Push down the green levers and
remove the paper feed roller module
from the scanner by holding the green
levers. (2)
•
The paper feed roller block is attached by
a magnet.
•When moving the green levers, do not
apply pressure in any other direction
than the arrows.
They may break.
Front door
Front door release 
(I id h f d )
Paper feed roller block
1
Green levers
2
2
: off position
Power switch 
						

							42
Replacing Consumables
4Open the optional “Roller Exchange
Kit (KV-SS009)”, and take out the
paper feed roller module.
For supplies and accessories: 
Call 1-800-346-4768 (U. S. A. only) or
your dealer.
5Install the new paper feed roller
module with the gear on the left side
and the bearings into the guide
grooves of the side chassis in the
scanner. (1)
Then push up the green levers on both
ends until they click into place. (2)
•
Match the paper feed roller module with
the bearings and guide grooves, and then
attach it.
Bearing
Side chassis
Green levers
22
Guide groove
Guide groove
1
1
Gear
Bearing 
						

							43
Replacing Consumables
6Push up on the paper feed roller block
and it will magnetically attach to the
chassis.
•
When attaching the paper feed roller
block to the chassis, do not damage the
roller.
•You are now finished attaching the paper
feed roller module.
To continue, replace the retard roller
module according to the following
procedure. (The retard roller module is
located in the conveyor.)
7Pull open the conveyor towards you by
using the indent on the right side.
•
When the conveyor is pulled towards you,
the click-stop mechanism will be
released.
•When opening the conveyor, be careful
not get your finger stuck in the indent.
8Pull the right side of the shaft in the
direction of the arrow and hold it there.
(1) 
Pull the retard roller module in the
direction of the arrow (2) and then
remove it.
Shaft
Retard roller module
12
ConveyorIndent 
						

							44
Replacing Consumables
9Take out the retard roller module in the
optional “Roller Exchange Kit (KV-
SS009)”.
For supplies and accessories: 
Call 1-800-346-4768 (U. S. A. only) or
your dealer.
10Pull the right side of the shaft in the
direction of the arrow and hold it there.
(1)
Attach the new retard roller module as
shown in the diagram on the right (2)
and then return the right side of the
shaft in the direction of the arrow. (3)
•
Confirm if pin A and pin B are inserted in
their notches correctly.
•Attach the retard roller module so that the
notch A is on the left side.
2
3
Notch A
Pin APin B
Notch B
Shaft
Retard roller module
1
When the pin is not inserted in the notch
properly, it may cause double feeding or a paper
jam. 
						

							45
Replacing Consumables
11Hold the conveyor using both hands,
and close the conveyor by pushing it
into the unit.
•
When the conveyor is closed, the click-
stop mechanism will operate.
•If the conveyor is not closed correctly
and the operation in step 12 is done, the
conveyor may break.
12Close the front door.
•
Push both sides of the front door down
slowly until it clicks into place.
•After replacing rollers, clear the “Replace
Roll. Warning”  display.
(Refer to page 28.)
Conveyor
Before closing the front door, confirm that 
the conveyor is closed correctly. Or, the 
conveyor may break. 
						

							46
Repacking Instructions
It is highly recommended that you keep the original carton and ALL packing materials. lf you need to transport or
ship your scanner, please follow these instructions.
Please Note :
•
Please use the original carton and all of the original packing materials. If you do not have the original packing
materials, these are available from your Panasonic dealer. Please refer to your service dealer, or call 1-800-833-
9626 (U. S. A. only) or your dealer.
•Improper repacking of the scanner may result in a service charge to repair the unit.
•The scanner should be handled in the correct (horizontal) position.
Materials Required :
•
Original Scanner Carton & Packing Materials
•Shipping Tape and Scissors
1Disconnect your scanner from the electrical outlet and the interface cable.
2Fold the plastic part of the exit stopper and put the exit stopper into the exit extension
tray. Slide the exit extension tray into the pre-imprinter door if it is pulled out.
3Attach the screw, fixture and sheet for
transportation.
4Pack the scanner.
Screw
Fixture
Blower
Power cord
Driver software (CD-ROM 1 piece)
Operating Instructions
³Installation manual
³Maintenance manual
³Roller cleaning paper 
  (3 pieces)
Joint
Screw
Pre-imprinter 
doorSheet
Fixture 
						

							 
47 
Specifications 
“Weight in pounds” of paper represents the weight of 500 [17  
a  
22 inches (432  
a  
559mm)] sheets. 
Model No.
Item 
KV-S2065L
KV-S2065W
 
Scanner  
Scanning face Duplex scanning
Scanning methodFront side : CIS (Contact Type Image Sensor)
Back side : CIS (Contact Type Image Sensor)
Readout speedSimplex scanning 
Approx. 62 sheets/min. (Letter, fed lengthwise, 200dpi)
Approx. 60 sheets/min. (A4, fed lengthwise, 200 dpi)
Duplex scanning  
Approx. 58 sheets/min. (Letter, fed lengthwise, 200 dpi)
Approx. 56 sheets/min. (A4, fed lengthwise, 200 dpi)
ResolutionMain scanning direction  : 100   
T  
 600dpi (1 dpi step)
Sub-scanning direction   : 100   
T  
 600dpi (1 dpi step)
(Same as main scanning direction)
The optical resolution is 400 dpi.
Tonal gradationBinary mode, Grayscale mode (4/8 bit), 64-step gradation 
(dither) mode, 64-step gradation (error diffusion) mode
Image controlImage emphasis, Dynamic threshold (DIMM module required), 
Automatic threshold, Automatic separation, Monochrome 
reversing, Automatic back control
Compression MH, MR, MMR
PaperSizeScanning size :
48  
a  
70mm (1.9  
a  
2.75 in.) to 
216  
a  
431mm (8.5  
a  
17 in.)
Feeding size  :
48  
a  
70mm (1.9  
a  
2.75 in.) to 
305  
a  
838mm (12  
a  
33 in.)Scanning size :
48  
a  
70mm (1.9  
a  
2.75 in.) to 
298  
a  
431mm (11.7  
a  
17 in.)
Feeding size  :
48  
a  
70mm (1.9  
a  
2.75 in.) to 
305  
a  
838mm (12  
a  
33 in.)
ThicknessSingle paper feeding         : 0.025 to 0.2mm (1.0 to 7.9 mils)
Continuous paper feeding : 0.06 to 0.2mm (2.4 to 7.9 mils)
Note : 1 mil=1/1000 in.
WeightSingle paper feeding         : 20 to 157   
g  
/m 
2 
 (5.3 to 42 lbs.)
Continuous paper feeding : 50 to 157   
g  
/m 
2 
 (13 to 42 lbs.)
Interface SCSI  
III  
 (20 MB/sec.), 50 pin  
Unit 
External dimensions
(Width 
a 
Depth  
a  
Height)495   
aa a a  
575   
aa a a  
246mm (19.5   
aa a a  
22.6   
aa a a  
9.7 in.)
Mass (Weight) 19k 
g  
  (41.8 lbs.)
Power requirement AC100 - 120V,  50/60Hz  AC220 - 240V, 50/60Hz 
Power 
consumption
 
Maximum
(Scanning)1.3A (AC100 - 120V) 0.8A (AC220 - 240V)
Minimum
(Standby)0.5A (AC100 - 120V) 0.3A (AC220 - 240V)
Sleep mode 0.13A (AC100 - 120V) 0.07A (AC220 - 240V) 
						

							 
48 
Specifications 
Model No.
Item 
KV-S2065L
KV-S2065W
 
Operating 
Environment  
Operating temperature 
and humidity15°C to 30°C (59°F to 86°F), 30% to 80%RH  
Storage 
Environment  
Storage temperature and 
humidity0°C to 35°C (32°F to 95°F), 10% to 80%RH  
Option  
Roller exchange kit (KV-SS009), lmprinter option (KV-SS010), 
Roller cleaning paper (KV-SS03), Ink cartridge (KV-SS06), 
White roller kit for KV-S2065W (KV-SS048), White roller kit for KV-S2065L (KV-SS071) 
						

							 
49 
Troubleshooting 
If a problem occurs while the unit is being used, first check the following items. If the unit still malfunctions, turn it
OFF, unplug the power cord and call for service. 
Symptom
Possible CauseRemedy
 
The LCD does not display 
when the power switch is 
turned ON.The power cord is not plugged in. Insert the power plug firmly.
A fuse has blown.
Pull out the power plug, then call for 
service. Foreign matter is lodged in the fan, 
preventing it from rotating.
A double feeding problem 
occurs.The rollers are dirty.Clean all of the rollers. (See page 36 
through 38.)
The ADF / manual feed selector is not 
set properly.Adjust the ADF / manual feed selector. 
(See page 33.)
Retard Roller is not installed correctly.
The document stops during 
scanning.The document is creased or torn, or 
longer than A3 size or smaller than 
48  
a  
70mm (1.9  
a  
2.75 in).Make a copy of the document on paper 
of the specified size [between 
48  
a  
70mm (1.9  
a  
2.75 in.) and A3 size] 
and scan the copy.
The document is jammed.Refer to the next page when an error is 
displayed. 
(See pages 50 and 51.)
The document is not fed 
smoothly during scanning.The rollers are dirty.Clean all of the rollers. 
(See page 36 through 39.)
The scanned document is 
blank.The document to be scanned was 
loaded face down (upside down).Load the document correctly.
The scanned document is 
skewed.The document guides were not touching 
the edges of the document, or the 
document was skewed when loaded.Set the document guides or the 
document correctly.
Vertical lines appear on the 
scanned document.The sensor rollers, scanning section glass 
or the rubber rollers are dirty.Wipe the dirty parts with a clean cloth.
(See page 36 through 39.)
The computer does not 
recognize the scanner. The 
scanner does not operate 
correctly.The computer cannot recognize the 
scanner.Turn the computer OFF. Turn the scanner 
ON, and then turn the computer ON again.
Confirm the SCSI ID, product ID and 
terminator, and then set them correctly.
Use a shielded cable which is as short 
as possible.
Reduce the SCSI transfer rate, and 
then proceed. (See page 27.)
The scanned document is 
faint.The sensor rollers are dirty.Clean the sensor rollers. 
(See pages 38 through 39.)
The double feed detection 
sensor is not operating.There is dust from the paper on the 
double feed detection sensor.Please clean the double feed detection 
sensor with the included blower. (Refer 
to page 39.) 
						

							 
50 
Troubleshooting 
LCD 
Possible CauseRemedy
 
The rollers are dirty.Clean the rollers. 
(See page 36 through 38.)
The rollers need to be 
replaced.Replace the paper feed roller 
module and retard roller module. 
(See pages 41 through 45.)
Multiple sheets were fed into 
the unit.Open the front door and remove 
the jammed paper.
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
The document is jammed.Open the front door and remove 
the jammed paper. 
(See page 35.)
A document remains in the 
scanner.Open the front door and remove 
all of the remaining documents.
Dust adheres to the document 
sensors.Clean a dust using the included 
blower. 
(See page 39.)
Multiple sheets were fed into 
the unit.Open the front door and remove 
the jammed paper. 
(See page 35.)
The front door is open. Close the front door.
]]]Warn
C l ean Ro l l e	r ing]]]
]]]Warn
Re p l a c e Ro l l e	r ing]]]
]]]Warn
Db l . F e e d Oc c u r e ding]]]
U1 1 J AM
55555555
U1 2 J AM
55555555
U1 3 J AM
55555555
U1 4 J AM
55555555
U1 5 J AM
55555555
U1 6 J AM
55555555
U1 7 J AM
55555555
U 1 8 R ema
55555555ind Doc.
U23 Doub
55555555l e Feed
U3 0 F r o n
55555555tDoor