Panasonic High Speed Scanner Kvs2065l Operating Instructions

							21
Display Panel Instructions
06    Back side dropout colorColor selection
07    Back side brightness
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒNormÓ.
¥ÒDÓ means dark. ÒLÓ means light.
08    Back side image emphasis
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒMediumÓ.
09    Back side contrast
¥When ÒHostÓ is displayed, pressing the 1 key or the 2 key
will change the display to ÒNormÓ.
¥ÒHÓ means high. ÒLÓ means low.
10    Back side halftone
¤
1The dynamic threshold is not displayed if the DIMM
expansion memory module has not been installed. If the
dynamic threshold is to be used, install a DIMM memory
module which is available on the market.  For details on
how to install it refer to the installation manual.
11    Noise reduction
B1 
a 1TB6 a 6   : Scanner reduces a black dot.
W1 
a 1TW6 a 6 : Scanner reduces a white dot.
06 .B.Co l
	Ho s t or dropGreen Red Host
07 .B.Br ightness
D
L	Ho s tD4 D2D3 D1 Norm
HostL4 L3 L2 L1
08 .B.Emp
	Ho s t hasis
None Smooth Low Medium
HostHigh
09 .B.Contrast
LH	Ho s tL4 L2L3 L1 Norm
HostH4 H3 H2 H1 
10 .B.Ha l
	Ho s t f t one
Binary Host Bayer dither 64 Bayer dither 16
(Dynamic Threshold)
Halftone dot 32 Error diffusionHalftone dot 64

¤1   
11 . No i seReduc t .
	Ho s tNone Host B151B252
B353
B454B555
B656W151W252
W353W454W555W656
 
 
  
  
						

							22
Display Panel Instructions
•When scanning a document which is shorter than 210 mm / 8.3 (A5 size) in length, double feed detection will
not work well.
•Thick, creased, or edited documents with correction fluid as well as documents with holes near the center may
give you false double feed warning. 12    Black line removal
•This setting is valid only when the white roller kit is installed.
13    Scanning mode
Fit to Page : Scanner shrinks image to fit scanned page.
Actual 
:Scanner scans at 100% actual page size. 
Some of the data on the edges of the page may be
lost.
14    Double feed detection
If set to “Detect”, the scanner will sound a buzzer and the power
indicator will flash red when double feeding is detected. Even if
this buzzer is set to “OFF” in “Setting the buzzer” (see page 27),
it will still ring.
•When scanning very important documents, confirm if the
number of scanned pages displayed on the LCD matches the
number of actual pages.
15    Setting the “Double Feed” detector 
action
Host 
:The scanner will act in response to commands from the 
host computer.
Stop 
:The scanner will display double feeding error and stop 
when it detects double feeding.
Buzzer 
:When the scanner detects double feeding, it will sound
a buzzer, the power indicator will light red and it will
continue scanning. 
After completing scanning, the scanner will display
double feeding warning.
16    Setting the double feed detector 
sensitivity
Low sensitivity: The double feed detector’s sensitivity will be low.
Set this when there is an error for no double
feeding.
High sensitivity: The double feed detector’s sensitivity will be
high. Set this when there is no error for double
feeding.
1 2 . BLK L
Remove	Ho s t ine
Disable Host Enable
13 . Scann
	Ho s t i ng Mode
Fit to Page Host Actual
14 . Doub l
	Ho s t e Feed
Not detect Host Detect
15 . Doub l
Ac t i on	Ho s t e Feed
Stop Host Buzzer
16 . Doub l
	Ho s t e Feed
 Sen s ·
Low sensitivity Sens. Host
Normal Sens. High sensitivity
    
  
						

							23
Display Panel Instructions
•Scanning settings 01-17 must be saved using setting “18 Save scanning settings (Execution)”. 
Even if they are not saved, they will be applied. If the power is turned off, the next time the unit is used they will
not be applied. 17    Feed speed
 Fast : The scanner scans approximately 1.3 times faster than
when “Normal” is set, at a resolution ranging from
200dpi to 400dpi.  For example, when the resolution is
200dpi, the scanner scans at 200dpi a 150dpi, but
outputs the image at 200dpi a 200dpi.  However, the
image quality produced by “Fast” is inferior to the image
quality produced by “Normal”.
Slow : The scanner scans at half of the “Normal” speed.
18    Save scanning settings 
(Select memory)
18    Save scanning settings (Execution)When pressing the 
1 key and the 2 key simultaneously, the
scanning conditions set in 01 to 17 above will be saved in the
memory selected in the “Save scanning settings (Select
memory)”.
“Completed” will be displayed after saving.
19    Load scanning setting
•If you use the 1 key or the 2 key to select Memory 1 or
Memory 2, the saved scanning items will become valid by
the “Save scanning settings (Execution)”. If other scanning
items have been saved in another memory, during scanning
you can change the scanning items easily. This setting will
not be changed even if the power is turned off and on, and
will remain valid.
•If “Default” is selected, all of the saved scanning settings will
return to the default values. (See “01”  to “17” of the left side
display.)
17 . Feed
	Ho s t Speed
Slow Host Normal Fast
18 . SaveSe t t i n g
Memo r y 1
Memory 1 Memory 2
18 . Save
Exec Se t t i n g
19 . Load
Defaul t Se t t i n g
Memory 1 Memory 2 Default 
						

							24
Display Panel Instructions
Counter setting menu (by pressing the COUNTER key)
Number, mode and default display 
¥Pressing the 3 key will change to the
next mode. 
¥Pressing the 4 key will change to the
previous mode.Contents
¥Pressing the 1 key or the 2 key will change to another value.
01    
Select the counter displayed on the LCD
Scan : After scanning one time, the scanner counter will be
cleared.
User  : This counter is set to the default value. 
The user counter extender is also set by the user. 
They will be cleared when the power is turned OFF.
System: Displays the total amount of scanned documents up to 
now.
02    Setting the user counterPressing the 
1 key once will increase the user counter by one.
Pressing the 
2 key once will decrease the user counter by one.
Pressing the 
1 key or the 2 key continuously will change the
user counter value by increments of 10.
02    Setting the user counter extender
Pressing the
1 key once will increase the user counter extender
by one. Pressing the 
2 key once will decrease the user counter
extender by one.
02    Clear the user counterWhen pressing the 
1 key and the 2 key simultaneously, the
user counter will be cleared.
Then ÒCompletedÓ will be displayed.
03    Displaying the system counter
(ex.)Displays the total amount of scanned documents up to now.
01 . D i sp .
	Sc an Counter
User System Scan
02 . Use r
	0 Counter
02 . Use rCounterr2 r1r3......
r8 r7
r9
02 . Use r
Cl earCounter
03 . Sy s t e
1234567 m Coun t . 
						

							25
Display Panel Instructions
Imprinter setting menu (by pressing the IMPRINT key)
Both a pre-imprinter and post-imprinter can be installed at the same time. However, the operator may only use
one imprinter at a time. If both of the imprinters are installed, you can set the following conditions.
Number, item and default display
•Pressing the 3 key will change to the
next mode.
•Pressing the 4 key will change to the
previous mode.Contents
•Pressing the 1 key or the 2 key will change to another value.
01    Setting the pre-imprinter data
•This setting can be done only when a
pre-imprinter is installed.Host : 
Count : Printing will be done according to the host computer.
Printing will be done according to the counter in the
“Select counter displayed on the LCD”.
02    Setting the pre-imprinter position
•This setting can be done only when a
pre-imprinter is installed.By pressing the 
1 key or the 2 key, you can specify the line
where printing starts from the top of the document. If “0”
character is set, printing starts from 10.0 mm. 
The millimeter value displayed is an approximation.
The length per character varies, depending on the 04 orientation
setting.
90°or 270°: 2.40mm per character
0°or 180°: 3.46mm per character
Character: 0 - 72
•In this example, printing starts at 12.4 mm (approx. 1/2 in.)
from the top of the paper. The number 12.4 can be changed
from 10.0 to 182.8 by pressing the 
1 key or the 2 key.
03    Setting the pre-imprinter font style
•This setting can be done only when a
pre-imprinter is installed.
Bold     : 
Normal: 
2-dot font
1-dot font that can increase the ink lifetime longer than
Bold fonts.
01 . P r e I
	Ho s t mp r i n t
Count Host
02 . P r e P
Ho s t osition
02 . P r e Position
	1Ch a r
12.4mm
Top of the paper Top of the paper
Top of the
printout
ABCD ......
ABCD ......Top of the
printout
10mm (Default)
12.4mm
Approx.
1/2 in.Approx.
13/32 in.
03 . P r e
	Ho s t Fon t
Normal Bold Host 
						

							26
Display Panel Instructions
04    Setting the pre-imprinter orientation
•This setting can be done only when a pre-
imprinter is installed.
11    Setting the post-imprinter data
•This setting can be done only when a post-
imprinter is installed.This is the same as the pre-imprinter.
See “01 Setting the pre-imprinter data”.
•You cannot set the pre-imprinter and post-imprinter to
“Count” at the same time.
12    Setting the post-imprinter position
•This setting can be done only when a post-
imprinter is installed.This is the same as the pre-imprinter.
See “02 Setting the pre-imprinter position”.
13    Setting the post-imprinter font style
•This setting can be done only when a post-
imprinter is installed.This is the same as the pre-imprinter.
See “03 Setting the pre-imprinter font style”.
14    Setting the post-imprinter orientation
•This setting can be done only when a post-
imprinter is installed.This is the same as the pre-imprinter.
See “04 Setting the pre-imprinter orientation”.
04 . P r e R
	Ho s t otate
Host 0o90o180o270o
A
B
A
B
AB
AB
:Transfer direction
Prints portrait orientation.
Rotates character string 90 degrees and prints.
Prints portrait orientation from the end of 
the character string.
Rotates character string 270 degrees and prints.
0x
90x
180x
270x 
11 . Pos t
	Ho s t Imp r i n t
12 . Pos t
  Ho s t Position
13 . Pos t
	Ho s t Fon t
14 . Pos t
	Ho s t Rotate 
						

							27
Display Panel Instructions
Others setting menu (by pressing the OTHERS key)
Number, mode and default display
¥Pressing the 3 key will change to the
next mode. 
¥Pressing the 4 key will change to the
previous mode.Contents 
¥Pressing the 1 key or the 2 key will change to another value.
01    Checking the versionMX.XX : 
FX.XX  :
BX.XX  : 
XXXM:Displays the mechanical control Þrmware version.
Displays the pre-imprinter Þrmware version. If a
pre-imprinter unit is not installed, the entry will
remain blank. 
Displays the post-imprinter Þrmware version. 
If a post-imprinter unit is not installed, the entry will
remain blank.
Displays the size of an optional memory. If an
optional memory is not installed, this will not be
displayed.
02    Setting the buzzer 
03    Setting the SCSI ID 
¥Setting the SCSI ID will be activated after turning the power off
and turning it on again. 
04    Setting the terminator
When the scanner is located to terminal position on SCSI bus,
set to ÒEnableÓ. 
¥Setting the terminator will be activated after turning the power
off and turning it on again.
¥The internal terminator works only when the unitÕs power has
been turned on.  If the PC is to be used while the unitÕs power
is off, be absolutely sure to install an external terminator which
is available on the market.
05    Setting the transfer rate
¥Changes the maximum value of the synchronous transfer rate
of the SCSI interface.
¥Lower the synchronous transfer rate to 10 Mbytes/sec. if the
computer has failed to recognize the scanner or the scanner
fails to operate properly.
01 . Ve r s ion
02 . Buzze
	ON r
OFF ON
0 3 . SCS I
		No.6 ID
2 135 467
0
04.Termi
E	nable nator
Disable Enable
05.TransferR	ate
2	0MB y t e	/s	ec20MByte/sec10MByte/sec 
						

							28
Display Panel Instructions
06    Checking the roller cleaning warning  0%: This is displayed when “Clean Roller Warning ²²%” 
displayed is cleared. 
100%: This is displayed when the roller needs to be cleaned. 
06    Clearing the roller cleaning warningWhen pressing the 1 key and the 2 key simultaneously,
“Clean Roller Warning” will be cleared. Then “Completed” will be
displayed.
07    Checking the roller modules 
replacement warning  0% : This is displayed when “Replace Roll. Warning ²²%”
displayed is cleared. 
100% : This is displayed when the roller modules need to be
replaced.
07    Clearing the roller modules 
replacement warningWhen pressing the 
1 key and the 2 key simultaneously, 
“Replace Roll. Warning” will be cleared. Then “Completed” will 
be displayed.
08    Setting the product ID
The applications for the scanner which have been set can be
used.
•An error results if an attempt is made to use a function which
are not provided with the KV-S2065 series of scanners.
•No guarantees are given for complete compatibility.
09    Setting the sleep mode
To conserve energy and operating cost,
this scanner is provided with a
programmable power save feature. The
scanner is factory set with the power save
feature (sleep mode) turned on to comply
with E
NERGY STAR® requirement. If sleep
mode is enabled, the scanner enters the
sleep mode when the scanner is idle for 15
minutes.
•1min. T 60min.
•To return from the sleep mode, press any key on the scanner
or issue the scan instruction from the application.
06 . C l ean
Warning Ro l l e r
  0  %
06 . C l ean
Warning Ro l l e r
07 . Rep l a
Warning			0% ce Ro l l .
07 . Rep l a
Warning
ce Ro l l .
08 . P r odu
KV - S2065ct ID
KV-S2065KV-SS855
KV-S2055KV-S6045
KV-S6055
09 . S l eep
Af t er 15mi n .Mode
Disable After 1 min. T After 60 min. 
						

							29
Display Panel Instructions
´Other display explanations
DisplayContent
This will be displayed when scanning is started until it is
completed. 
After completion, “Ready” will be displayed.
If the STOP key is pressed, scanning will stop. This will be
displayed when the STOP key was pressed during scanning.
Even if the STOP key is pressed in a setting mode, this will be
displayed. Then the scanner will return to setting mode after
stopping scanner operation.
This will be displayed when the STOP key is pressed and the
scanner stops.
Even if the document remains in the scanner, “JAM” will not be
displayed. 
If the document remains in the scanner, open the front door
and remove it.
Then “Ready” will be displayed.
This will be displayed after setting scanning to start with a host
computer.
If the document is set and the START key is pressed, scanning
will start.
This is displayed in the sleep mode.
To return from the sleep mode, press any key on the scanner
or issue the scan instruction from the application.
Scanning...
	1
Stopping...Wait!
123	45678
Scanne rS t opped
123	45678
Pr essSTART Ke y
1
S l eep 
						

							 
30 
Loading Documents 
1
 
Documents that have been stapled
together or stacked together (as in a
file folder), will need to be separated.  
1  
Fan the stack of documents to
separate all the edges.  
2  
Hold both ends and bend the
documents as shown in the
illustration.  
3  
To straighten the documents, hold
firmly and pull them apart as shown
in the illustration.
Repeat these steps as necessary. 
2
 
Carefully align the documents. 
3
 
Adjust the document guides slightly
larger than the actual size of the
document.
Document guide
1
23
Prior to scanning, remove, all staples and paper clips 
from pages.