Panasonic High Speed Scanner Kvs6050w Operating Instructions

							11
Precautions
Operating Environment
³³ ³ ³
Power Source
•
Use a voltage level that does not vary more than ±10 % from the voltage level marked on the nameplate
(located on the back side of the scanner ).
•Do not use an extension cord.
•This scanner should be connected to a grounded outlet.
•Do not use a line conditioner, transient suppressor or surge protector. Do not place the unit in direct sunlight or in a cold draft. Do not operate or place the unit in a vertical position.
Do not place the unit near a heating appliance or an air
conditioning vent. Do not place the unit in a room with
extremely high or low humidity.Do not place the unit near other appliances which
generate large electrical noise.
Do not place the unit on a carpet. (Static electricity can
cause the unit to malfunction.)Do not drink or inhale the included roller cleaning paper
fluid.
The roller cleaning paper may be harmful to sensitive
skin, so please use protective gloves.
Do not use the roller cleaning paper near a heater or
open flame. This may cause a fire. 
						

							12
Precautions
ºº º ºCD-ROM
To prevent the CD-ROMs from accidental damages:
Do not touch or write on the surface
of the disc.Do not leave the disc out of the
protective case.Do not leave the disc in direct
sunlight or near heat sources.
Do not place heavy objects on the
disc case or drop the case.To clean the disc, hold the disc by
its edges and wipe it from the
center to the edges with a dry, soft
cloth. 
						

							13
Component Identification
 
Hopper
ADF door release
Inside the ADF door.
ADF door
Manual feed selector 
Front door
Exit substopperDocument guide
Display panel
When performing 
each setting, used to 
display the scanning 
conditions, etc.
Power indicator
When the power is turned on, 
the green indicator lights.
When an error occurs, the 
indicator will change to red, 
and light steadily or flash.
Front door release
Inside the front door.
Exit document stopperDocument cover
AC inlet
Fan exhaust ventImprinter door 
(Top door)
Used for attaching the 
imprinter unit and ink 
Power switch
 [: on position
²: off position
Hopper extension tray
Connectors
Used to connect the  
scanner unit to a 
host computer.
Power cord 
						

							Component Identification
14
Component Identification
Standard mark
Document glass
Cover sheet
(black sheet)
CIS glass
(For KV-S6055W series only)
Scanning section glass 
						

							15
Display Panel Instructions
The required settings must be selected prior to scanning.
Information and conditions are shown on the LCD (Liquid Crystal Display).
ºº º ºDisplay panel and keys
Ready
: Press to enter the scanning setting menu.
Up to 32 characters can be displayed
during scanning or setting.
: Press to enter the counter setting menu.
: Press to enter the imprinter setting menu.3: Press to advance to the next mode in the
selected menu.
: Press to enter “others” setting menu.4: Press to return to the previous mode in
the selected menu.
: Press to exit from the setting section and
return to the ready status. 
Also, this function can change the display
language.1: Press to advance to the next value in the
selected mode.
: Press to start or stop scanning a document
or batch of documents.2: Press to return to the previous value in
the selected mode.
SCAN COUNTER
IMPRINT
OTHERSREADY/
ERROR
STOP/START MODE
SELECT HOME
SCAN
LCD:
COUNTER
IMPRINT
OTHERS
HOME
STOP / START 
						

							16
Display Panel Instructions
ºº º ºSetting the language
•Select English, German or Japanese as the language which is to appear on the LCD display.
•The language setting mode is appeared automatically when the unit’s power is turned on for the first time after
the unit was purchased. English is the default language.
1Turn the power on while pressing 
the HOME key.
•
When “High Speed Scanner” or other
words appear on the LCD, release the
HOME key.
2Use the 2 key or the 1 key to select
“English Letter”, “English A4”,
“Deutsch A4” or  “  A4”.
3Press the HOME key.
•
The display will change to the selected
language, then the scanner will be ready.
•This setting will remain until it is changed
to another setting.
Se t L a ng ua ge
En g l i s hLe t t e r
D e u t s   c  h A 4 Se t L a ng ua ge
Bere i t 
						

							17
Display Panel Instructions
ºº º ºSetting the scanner
The following parameters can be customized using the scanner’s various setting modes. If the application
software provides these features, it will be supported by the scanner.
Scan menu
No.ItemLCDContentPage
01 Front side brightness F. BrightnessSelection for density when scanning the front
side of a document.
22 02
Front side image emphasisF. EmphasisSelection for emphasis when scanning the
front side of a document.
03 Front side contrast F. ContrastSelection for contrast when scanning the front
side of a document.
04 Front side halftone F. HalftoneSelection for gradation when scanning the
front side of a document.
23 05Back side dropout color 
(For KV-S6055W series only)B. Color dropColor selection for dropout when scanning
the back side of a document.
06Back side brightness
(For KV-S6055W series only)B. BrightnessSelection for density when scanning the back
side of a document.
07Back side image emphasis
(For KV-S6055W series only)B. EmphasisSelection for emphasis when scanning the
back side of a document.
08Back side contrast
(For KV-S6055W series only)B. ContrastSelection for contrast when scanning the
back side of a document.
09Back side halftone
(For KV-S6055W series only)B. HalftoneSelection for gradation when scanning the
back side of a document.
24 10 Noise reduction Noise Reduct.Selection for noise reduction when scanning
a document.
11 Black line removalBLK Line 
RemoveSelection to choose the black lines which
appear at the top, bottom and left/right sides
of the image after scanning the document.
12 Scanning modeScanning 
ModeSelects whether documents are scanned at
actual size or reduced (Fit to page) size.
13 Double feed detection Double FeedSelection to choose to detect double feeding
function.
When scanning very important documents,
confirm if the number of scanned pages
displayed on the LCD matches the number of
actual pages.
14Setting the “Double Feed” 
detector actionDouble Feed 
ActionSelects the action of the Double Feed
Detector when double feed occurs.
25
15Setting the “Double Feed” 
detector sensitivityDouble FeedSelects the sensitivity of the Double Feed
Detector. 
						

							18
Display Panel Instructions
Scan menu
No.ItemLCDContentPage
16 Feed speed Feed SpeedSelection for feed speed when a document is
being scanned.
25
17 Setting the “Detect Skew” Detect Skew Selects whether skew is detected or not
detected.
18 Scanning method Scan MethodSelection of documents to be scanned.
This includes documents placed in the ADF
and documents placed on the flatbed glass
(document glass).
26 19Save scanning settings 
(Select memory)Save Setting Selects the memory where the conditions are
saved into.
Save scanning settings 
(Execution)Save Setting Saves the scanning conditions into the
memory. (2 memory settings)
20 Load scanning setting Load SettingLoads the memory where the scanning
conditions have already been saved. If
“Default” is selected, all of the scanning
conditions will return to the default values. 
						

							19
Display Panel Instructions
Counter menu
Imprinter menu
Depending on the setting on the “Counter setting menu”, the page number of the scanned document will be
printed. The imprint unit (KV-SS010) is required. If a host computer is connected, there may be settings required
on the host computer as well.
No.ItemLCDContentPage
01Select the counter 
displayed on the 
LCD.Disp. CounterSelection to choose to display the cleared counter
(scan counter) after scanning one time or to display the
user set counter (user counter) on the LCD.
27
02Setting the User 
CounterUser Counter Selection for default number before scanning
Setting the user 
counter extenderUser Counter Selection for an increase in the default number
Clear the user 
counter.User Counter Clears the counter which was set by the user.
03 System Count System Count.Displays the total amount of scanned documents up to
now.
No.ItemLCDContentPage
01Setting the 
imprinter dataPre ImprintAllows for the selection of the printing content using an 
imprinter.
The imprinter will print on the printing (front) side of the 
document scanned.
28
02Setting the 
imprinter positionPre PositionAllows for the selection of the printing position using an 
imprinter.
03Setting the 
imprinter font stylePre FontAlows for the selection of the printing font style using 
an imprinter.
04Setting the 
imprinter 
orientationPre RotateAllows for the selection of the printing orientation using 
an imprinter.29 
						

							20
Display Panel Instructions
Others menu
No.ItemLCD ContentPage
01 Checking the version VersionDisplays the firmware version of the mechanical
control, pre-imprinter or post-imprinter.
If an optional imprinter is not installed, the imprinter
version will not be displayed.
30 02 Setting the buzzer BuzzerSelects whether the buzzer is turned on or off. 
If selection is in the “ON” position:
When pressing a key, one short beep will be heard.
When there is an error, 5 short beep will be heard.
When scanning is completed correctly, one long beep
will be heard.
03 Setting the SCSI ID SCSI ID Sets the SCSI ID No.
04 Setting the terminator TerminatorSet “Enable” or “Disable”.
“Enable”: If last device on chain
“Disable”: If between devices
05Setting the transfer 
rateTransfer Rate
•Changes the maximum value of the synchronous
transfer rate of the SCSI interface.
•Lower the synchronous transfer rate to 10 Mbytes/
sec. if the computer has failed to recognize the
scanner or the scanner fails to operate properly.
06Checking the roller 
cleaning warningClean Roller The alarm tells you it is time to check roller. 
If it is near 100%, clean the roller. See “Cleaning the
Unit” on page 44.
31 Clearing the roller 
cleaning warningClean Roller  Clear the “Clean Roller Warning ²²%” display.
07Checking the roller 
modules replacement 
warningReplace Roll. The alarm tells you the roller needs to be changed. 
If it is near 100%, replace the paper feed roller module 
and retard roller module. See “Replacing Consumable” 
on page 52.
Clearing the roller 
modules replacement 
warningReplace Roll. Clear the “Replace Roll. Warning ²²%” display.
08 Setting the product ID Product IDSelects the product ID. The product ID setting depends
on the host computer scanner application you are
using.
Allows scanner to emulate other Panasonic scanner.32
09Setting the sleep 
modeSleep Mode Sets the time until sleep mode turns ON.