Panasonic Multi Hybrid Control Panel Aw Rp505 Operating Instructions

							Multi Hybrid Control Panel
AW-RP505
Before attempting to connect or operate this product,
please read these instructions completely.
â 
						

							Warning:
Do not install this product near any object that burns easily.
In case of using a halogen lamp, installation of it near such
an object could cause a fire due to the heat generated by the
lamp.
This digital apparatus does not exceed the Class A limits for
radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department
of Communications.
WARNING:
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS
TURE.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated dangerous voltage
within the products enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appli-
ance.The serial number of this product may be found on the bot-
tom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
For U.S.AFor CANADA 
						

							-1-
CONTENTS
FEATURES .......................................................................................................................................................................................... 2
PRECAUTIONS ................................................................................................................................................................................... 3
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS  ............................................................................................................ 4
INSTALLATION OF PAN/TILT HEAD  ................................................................................................................................................. 19
CONNECTIONS .................................................................................................................................................................................. 22
OPERATING PROCEDURES  .............................................................................................................................................................. 26
RACK MOUNTING  ............................................................................................................................................................................. 34
SPECIFICATIONS ............................................................................................................................................................................... 36
ACCESSORIES ................................................................................................................................................................................... 37 
						

							-2-
FEATURES• The Multi Hybrid Control Panel AW-RP505 is combined
with the Multiport Hub (AW-HB505) to control up to five
Pan/tilt Heads (AW-PH300) and Color Video Cameras
(AW-E560).  With the Control Panel AW-RP505 con-
nected to the multiport hub with three coaxial cables
(5C-2V) and a single 10BASE-T straight cable (UTP
category 5), and with the Multiport Hub connected to
each camera and pan/tilt head with three coaxial
cables (5C-2V) and a single 10BASE-T straight cable
(UTP category 5), the Control Panel performs various
kinds of control on the cameras and pan/tilt heads,
and sends and receives camera video signals and
genlock signals.• The maximum cable length from this control panel to
the Multiport Hub is 10 meters.  The maximum cable
length between the multiport hub and the cameras and
pan/tilt heads is 500 meters.
• Head pan/tilt and lenz zoom/focus can be controlled at
varying speeds with the servo control, and can be pre-
set at up to 10 points per pan/tilt head.
• With the auxiliary control input connector (AUX CON-
TROL IN), pan/tilt, zoom, focus, and iris operations can
be externally controlled. 
						

							-3-
PRECAUTIONS• Use only with AC Adaptor AW-PS301.
• Handle the control panel with care.
Dropping the control panel or subjecting it to a strong
shock can cause a failure or an accident.
• Operating temperature range –10°C to +45°C
Avoid using it in a cold place below –10°C or a hot
place above +45°C because low or high temperature
will adversely affect the parts inside.
• Switch power off before power cable connection or
disconnection.
Be sure to switch power off before connecting or dis-
connecting the power cable.
• Avoid outdoor use.
• Install the control panel more than 1 meter away
from the monitors.• Do not use benzine, paint thinner, or other volatile
liquids.
• When using a chemical duster, carefully read the
caution notes on its use.
Note
Set the power control switch to the OFF position after
setting the lamp switch to the OFF position.  Halogen
lamp power will not be switched off if the AC adapter for
the AW-RP505 is disconnected or if the main circuit
breaker is opened while the halogen lamp is in use.Precautions in Using Halogen Lamp • Care
Pull out the power cable plug, and wipe the control
panel clean with a dry cloth. If it is extremely dirty, dip
a cloth into a diluted solution of kitchen detergent,
squeeze it hard, and wipe the product surfaces care-
fully. 
						

							-4-
SPEED FOCUS PA N  /  T I LT
ZOOM
TELE
WIDEFA R
LEFT RIGHTUP
DOWN
NEAR
DEFON
OFF ON
OFF
POWEROPERATE
IRISCAM
CONT
BAR
CAMMODEGAIN AWC
SCENE
FILEABC
AT W
A
B
AUTO/ATW
ELC LOW MID
MANUON SC H
OFF HIGH AGC
OFF 1 / 100SHUTTER
ON
OFF
LAMP
MEMORY
ON
OFF AUTO
MANUON
OFFON
OFFON
OFF ON
OFFON
OFF
WIP
EXT ND OPH / F
1 .
2 .
3 .
4 .
G/L PHASE
PRESET
T.PEDMulti Hybrid Control Panel AW-RP505
154 3 2 154 3 2
2 1345
67891090¡  180¡ 
0¡      270¡
LEVEL
TALLYCONTROL
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Note:To control the cameras and
pan/tilt head, the power switch
on the Multiport Hub must be in
the ON position.
Only the camera and pan/tilt
head selected with CONTROL
Switch 
@2can be set and con-
trolled.  First, select a camera
with CONTROL Switch @2 set
CAM CONT Switch rto the ON
position, and make the neces-
sary settings.  After setting the
camera, set CAM CONT Switch
rback to the OFF position.
nControl Panel 
						

							-5-
qPower Indicator [POWER]
Lights red when POWER ON/OFF Switch wis in the
ON position, and goes out when the same switch is set
to the OFF position.
wPower CONTROL Switch [POWER, ON/OFF]
All the connected cameras and pan/tilt heads are
switched on when this switch is set to the ON position.
(The power indicator lights.)  The camera and pan/tilt
head are partially switched off when this switch is set to
the OFF position.
Note:When the switch is set to the OFF position, the
camera is totally switched off but the communica-
tion line between the pan/tilt head and this control
panel remains live.  To disconnect all power sup-
ply, pull out the power plug from the electrical out-
let.
eOperating Indicator [OPERATE]
Lights green when communication begins normally
between the camera and the control panel, and goes
out if a communication error occurs.
rCamera Control Switch [CAM CONT, ON/OFF]
Before making camera settings, select a camera with
CONTROL Switch @2then set CAM CONT Switch rto
the ON position.  After making the necessary settings,
set CAM CON Switch rback to the OFF position.
Note:At the same time as CAM CONT Switch ris set
to the ON position, all the switch settings of thiscontrol panel are sent to the selected camera to
update its settings.  Do not shift CAM CONT Switch
rto the ON position except when changing the
camera settings.  If a different camera is selected
with CONTROL Switch @2when CAM CONT Switch
ris in the ON position, the settings of the newly
selected camera will also be changed.  Before
selecting another camera with CONTROL Switch
@2, be sure to set CAM CONT Switch rback to
the OFF position.
tMode Selection Switch [MODE, BAR/CAM]
Used to select camera color bar signals or camera
video signals.  Select a camera with CONTROL Switch
@2, set CAM CONT Switch rto the ON position, then
select the desired type of signal with this switch.  With
the switch set to BAR, the control panel outputs color
bar signals from the video output terminal.  When the
switch is set to CAM, it outputs camera video signals.
After selecting it, set CAM CONT Switch rback to the
OFF position.
yAGC Selection Switch [GAIN, AGC/MANU]
Keep this switch in the AGC position if you want to
keep automatic gain control.  Select a camera with
CONTROL Switch @2, set CAM CONT Switch rto the
ON position, then select AGC or MANU as necessary.
When this switch is at AGC GAIN H/M/L switch uis
invalid.  After selecting it, set CAM CONT Switch r
back to the OFF position. 
						

							-6-
uGain Selection Switch [GAIN, HIGH/MID/LOW]
This switch is valid only when GAIN AGC/MANU
Switch yis in the MANU position. Select a camera
with CONTROL Switch @2, set CAM CONT Switch rto
the ON position, then select HIGH, MID, or LOW.
Normally, keep it in the LOW position.  When the cam-
era is used in a dark place or when video output level
is not high enough even if the iris is wide open, set the
switch to the MID or HIGH position.After selecting it,
set CAM CONT Switch rback to the OFF position.
iElectronic Shutter Speed Selection Switch
[SHUTTER, ELC/ 1/100 /OFF]
Used to select a mode of camera electronic shutter
control.  Select a camera with CONTROL Switch @2,
set CAM CONT Switch rto the ON position, then
select ELC, 1/100, or OFF.  With the switch in the ELC
position, the electronic shutter is controlled and the
camera sensitivity is automatically adjusted when
using the camera in a bright place.  The shutter speed
is 1/100 second when the switch is in the 1/100 posi-
tion.  The electronic shutter is off when the switch is in
the OFF position.  After selecting it, set CAM CONT
Switch rback to the OFF position.
oWhite Balance ATW Selection Switch 
[AUTO/ATW, ATW]
When this switch is depressed, the camera selected
with CONTROL Switch @2keeps automatically adjust-
ing white balance.  The switch lights when it is select-
ed.!0White Balance Ach Selection Switch 
[AUTO/ATW, A]
When this switch is pressed, white balance will be as
stored in Channel A of the camera selected with CON-
TROL Switch @2.  The switch lights when it is selected.
When AWC switch !2is pressed after selecting
AUTO/ATW, A, white balance is automatically adjusted
and stored in Channel A.
!1White Balance Bch Selection Switch 
[AUTO/ATW, B]
When this switch is depressed, white balance will be as
stored in Channel B of the camera selected with
CONTROL Switch @2.  The switch lights when it is
selected.  When AWC switch !2is pressed after
selecting AUTO/ATW, B, white balance is automatically
adjusted and stored in Channel B.
!2Auto White Start Switch [AWC]
If this switch is pressed when AUTO/ATW A Switch !0
or AUTO/ATW B Switch !1is selected, white balance is
automatically adjusted on the camera selected with
CONTROL Switch @2.  The adjustment results are
stored in Channel A or B.  This switch is invalid if the
MODE BAR/CAM switch t is in the BAR position.
Auto Set Indicator !4flashes while AWC is in operation,
and goes out when white balance has been properly
adjusted.  Auto Set Indicator !4 remains lit if white
balance adjustment fails. 
						

							-7-
Note:White balance may not be adjustable if there is
no white in the image being taken by the camera.
For details, refer to the Operating Instructions for
the Camera.
!3Auto Black Start Switch [ABC]
When this switch is depressed, the lens iris is
automatically closed to set black balance on the
camera selected with CONTROL Switch @2.   Be sure to
keep the IRIS AUTO/MANU switch @5in the AUTO
position in setting black balance.  Auto Set Indicator !4
flashes while ABC is in operation, and goes out when
black balance has been properly adjusted.  Auto Set
Indicator !4remains lit if black balance adjustment
fails.  Black balance adjustment may fail if the total
pedestal is too low.  In such a case, adjust the total
pedestal with T.PED Control @0(referring to the
Operating Procedures at page 26 and try to adjust
black balance again.
!4Auto Set Indicator
This LED flashes during white balance or black bal-
ance adjustment with AWC Switch !2or ABC Switch !3
depressed, and goes out when the adjustment has
ended normally.  The LED remains lit if balance adjust-
ment fails.
!5Scene File Selection Switch [SCENE FILE, 1/2/3/4]
Select a scene file preset on the camera side.
Remember, however, that [4] is camera scene file
USER A or USER B (provided that or AW-E560 is con-
nected).!6Genlock Phase Control Switch 
[G/L PHASE, ON/OFF]
Used to adjust the genlock phase in operating the
camera in external sync mode.  Select a camera with
CONTROL Switch @2, set CAM CONT Switch rto the
ON position, then set G/L PHASE Switch !6to the ON
position.  After G/L phase setting, set CAM CONT
Switch rand G/L PHASE Switch !6back to the OFF
position.
Note:If G/L PHASE Switch !6is set to the ON position
when CAM CONT Switch ris at ON, the genlock
phase setting data of this control panel is sent to
the camera to update its genlock phase settings.
Do not shift G/L PHASE Switch !6to the ON posi-
tion except when changing the camera genlock
phase settings.  If a different camera is selected
with CONTROL Switch @2when both CAM CONT
Switch rand G/L PHASE Switch !6are in the ON
position, the genlock phase settings of the newly
selected camera will be similarly changed.  Before
changing the camera for another, set G/L PHASE
Switch !6back to the OFF position.
!7Genlock Subcarrier Phase Coarse Switch
[G/L PHASE, 0°/90°/180°/270°]
Used for coarse adjustment of the color phases of gen-
lock input and video output signals in operating the
camera in external sync mode.  Used in combination
with G/L PHASE SC Control !8, the switch has an 
						

							-8-
adjustment range of over 360°.  Before making an
adjustment, set CAM CONT Switch rand G/L PHASE
Switch  !6to the ON position.  After the adjustment, set
both CAM CONT Switch rand G/L PHASE Switch !6
back to the OFF position.
!8Genlock Subcarrier Phase Fine Control 
[G/L PHASE, SC]
Used for fine adjustment of the color phases of gen-
lock input and video output signals in operating the
camera in external sync mode.  Use this switch in
combination with G/L PHASE Coarse Switch !7.
Before making an adjustment, set CAM CONT Switch
rand G/L PHASE Switch  !6to the ON position.  After
the adjustment, set both CAM CONT Switch rand
G/L PHASE Switch !6back to the OFF position.
!9G/L Horizontal Phase Adjustment Control 
[G/L PHASE, H]
Used to adjust the horizontal phases of genlock input
and video output signals in operating the camera in
external sync mode.  Before making a horizontal phase
adjustment, set CAM CONT Switch rand G/L PHASE
Switch !6to the ON position. 
@0Total Pedestal Level Control [T.PED]
The set pedestal level of the camera’s Y (luminance)
signal can be adjusted.  This control is used in a sys-
tem of two or more cameras to adjust the pedestal lev-
els of these cameras.  Select a camera with CONTROLSwitch @2, set CAM CONT Switch rto the ON posi-
tion, then adjust the total pedestal level with T.PED
Control @00.  The control may operate not continuous
sometimes due to digital signal processing.  After the
adjustment, set CAM CONT Switch rback to the OFF
position.
@1Tally Indicator [TALLY]
When a tally signal is input from a special effect gener-
ator (SEG) or video switcher, for example, to any of the
jacks [1] to [5] of TALLY Terminal #9, the correspond-
ing LED lights red.
@2Camera/Pan/tilt Head Selection Switch [CONTROL]
Select a desired camera with pan/tilt head from among
those connected to the control panel.  When a camera
with pan/tilt head is selected by pressing one of the
buttons [1] to [5], the pressed button lights.
Note:Even if an unconnected camera with pan/tilt
head is selected by pressing the corresponding
button, the button lights.
@3Lamp Indicator [LAMP]
Lights red when LAMP ON/OFF Switch @4is in the ON
position.  Flashes if the lamp connected to the AC
adapter (AW-PS300) for the pan/tilt head selected with
CONTROL Switch @2is broken.  Goes out when LAMP
ON/OFF Switch @4is set to the OFF position