Panasonic Multi Hybrid Control Panel Aw Rp505 Operating Instructions

							-19-
INSTALLATION OF PAN/TILT HEAD
Have a strong enough wire rod head and fasten it
securely to a firm board, such as of the ceiling.
Hole for wire rod to
prevent the head
from falling
• Install the pan/tilt head after carefully reading the
Operating Instructions for Pan/tilt Head.
• Have four hex bolts (M6 x 4) ready for mounting the
pan/title head.  Select bolts of a length appropriate to
the material and structure of the mounting base and
the overall weight applied to it.  Fasten the bolts
securely with plain washers, spring washers, and hex
nuts.  If the bolts are not securely tightened, the pan/tilt
head might fall to cause injuries or accidents.  In case
of suspending the pan/tilt head, locally purchase a
wire rod strong enough to hold the pan/tilt head, cam-
era, and lenses, pass it through the wire hole opened
in a firm board, such as of the ceiling, for example,
and fasten it securely.
• The switches on the pan/tilt head have been preset
before shipment from the factory on the assumption
that the pan/tilt head would be suspended from the
ceiling.  If the pan/tilt head is mounted on a board, for
example, be sure to shift the mounting direction
switches on the pan/tilt head.  Unless this is done,
pan/tilt directions will be reversed and pan/head oper-
ation limiter data cannot be properly stored in the
memory.  For details on shifting these switches, refer to
the Operating Instructions for Pan/tilt Head. 
						

							-20-
SW 2 SW 1 SW 3
SW 2 SW 1 DESKTOP
HANGING
• Changing Switch Settings on Pan/tilt Head 
qRemove the cover from the pan/tilt head.
* Be careful of the Tally Indicator wire.
wShift the mounting direction switches (SW1, SW2) on
the pan/tilt head depending on whether the head is
suspended from the ceiling or mounted on the floor.
They are originally set for suspended installation.
* Do not change the original set position of SW3.  If it is
changed, no operation can be controlled from the con-
trol panel.
Tally Indicator
ePlace the cover back on the pan/tilt head.
* Be sure not to trap the wires.
• If the pan/tilt head is connected to the multiport hub
with a cable longer than 300 meters, set the cable
compensation switch on the pan/tilt head to the ON
position in advance.  If the distance between the
pan/tilt head and the control panel is shorter than 300
meters, keep the switch in the original position (OFF).
For details on shifting the switch, refer to the figure
below or the Operating Instructions for Pan/tilt Head. 
						

							-21-
ON
OFF
• Shifting Cable Compensation Switch on Pan/tilt
Head
If the distance from the control panel to the pan/tilt
head is longer than 300 meters, set the cable compen-
sation switch to the ON position by observing the fol-
lowing procedure.
qRemove the controller connection panel from the
pan/tilt head.
* Be careful of the wires.
wShift the cable compensation switch on the inner side
of the controller connection panel of the pan/tilt head to
the ON position.
ePlace the controller connection panel back on the
pan/tilt head.• How to Mount the Lens
• Turn the lens lock ring knob fully counterclockwise.
• If the lens mount has a cap, remove the cap.
• With the lens positioning pin up, mount the lens.
• Turn the lens lock ring knob clockwise till the lens is
securely fastened. 
						

							-22-
CONNECTIONS• Before making any connection, switch off all the com-
ponents of the system.
• Use the Control Panel AC Adaptor AW-PS301 (option-
al), Multiport Hub AC Adaptor AW-PS505 (optional) and
Pan/tilt Head AC Adaptor AW-PS300 (optional).• Use the Multiport Hub AW-HB505, the Pan/tilt Head
AW-PH300 and the Color Video Camera AW-E560.
(The Color Video Camera WV-E550 cannot be used.)
To connect the pan/tilt head to the camera, the Camera
Cable AW-CA20T15 (optional) is necessary.
• Locally purchase a DC cable with a nominal cross sec-
tion of 1.25 mm
2or larger that meets the UL specifica-
tions, and connect the Pan/tilt Head AW-PH300 to the
Pan/tilt Head AC Adaptor AW-PS300 with that cable.
The maximum distance between the pan/tilt head and
pan/tilt head AC adapter is 30 m.
• Connect the Multiport Hub AC Adapter AW-PS505 to
the Multiport Hub AW-HB505.
• Connect the AC Adaptor AW-PS301 to the control
panel and clamp the DC cable of the AC adapter to the
cord clamp on the control panel.
• Connect the Pan/tilt Head AW-PH300 to the Color
Video Camera WV-E560 with the Camera Cable AW-
CA20T15.
DC Cord Cord Clamper
Control Panel 
AC Adaptor
AW-PS301 
						

							-23-
ITEM(AWC) UP(ABC)PAGEDOWN
  (BAR)IRIS
G/L  INVIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75ON
OFF
CONTROL
EXT DC INSEE MANUALCAUTION
• Connect the iris control cable of the motor-driven zoom
lens to the camera and the remote (zoom/focus control)
cable to the pan/tilt head.  If the remote (zoom/focus
control) cable of the motor-driven zoom lens is con-
nected to the camera, the lens cannot be controlled.• Connect the control panel to the multiport hub with the
three coaxial cables (video signal, G/L signal, camera
control signal)  and one 10BASE-T straight cable
(pan/tilt head control signal).  The maximum distance
between the control panel and pan/tilt head is 10
meters for coaxial cables 5C-2V and 10BASE-T straight
cable (UTP category 5 or equivalent).
• Connect the pan/tilt head to the multiport hub with the
three coaxial cables (video signal, G/L signal, camera
control signal) per pan/tilt head and one 10BASE-T
straight  cable (pan/tilt head control signal).  The maxi-
mum distance between the control panel and pan/tilt
head is 500 meters per pan/tilt head for coaxial cables
5C-2V and 10BASE-T straight cable (UTP category 5 or
equivalent).
• For further details on connecting the individual devices,
To Lens Interface ConnectorTo Iris ConnectorIris Control
Cable Remote (Zoom/Focus
Control) Cable 
						

							-24-
CAMERA
CONTROL OUTCAMERA
CONTROL IN VIDEO OUTPAM/TILT
CONTROL OUTPAM/TILT
CONTROL IN
S-VIDEO OUT VIDEO
IN
G/L
OUTG/L
IN
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
CAMERA
CONTROL OUTVIDEO OUTPAM/TILT
CONTROL OUT
S-VIDEO OUT VIDEO
IN
G/L
OUT
4
3
2
1 5
DC12V  IN
TO CAMERA PAM/TILT HEAD
TO CONTROL PANELPREVIEW OUT
SEE MANUAL
PAGEITEM(AWC) UP(ABC)DOWN  (BAR)IRIS
G/L  INVIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75ON
OFF
CONTROL
EXT DC INSEE MANUALCAUTION
AC IN
LAMP AC OUT
MIN  250W
MAX 500W
OPTION   SW
CONTROL OUTOPTION   SW
CONTROL INLAMP
CONTROL
OP SC
DC 15V
OUT- +
TALLYDC12V IN
AUX  CONTROL  IN1 2 3 4
5 
PREVIEW IN OUT G/L  OUTPREVIEW MONITOR OUT
CONTROL CONTROL  OUTPAN/TILT CAMERA
TD  MULTI  PORT  HUBG / L  IN
Connecting the control panel to Color Video Camera
(AW-E560), Pan/tilt Head (AW-PH300), and Pan/tilt
Head AC Adapter (AW-PS300)
Pan/tilt Head
AW-PH300Color Video Camera
AW-E560To Servo Control Zoom Lens
IRIS CONTROL
Camera Cable 
AW-CA20T15
Multiport Hub  AW-HB505
Pan/tilt Head AC Adaptor AW-PS300PREVIEW OUT
G/L THROUGH OUT
G/L IN
PAN/TILT CONTROLZOOM/FOCUS
CONTROL
CAMERA CONTROL
GEN-LOCK
VIDEO
DC+15V 
						

							-25-
S-VIDEO VIDEO
PREVIEW
VIDEO
VIDEO
CONTACT PAN/TILT
CONTROL
PAN/TILT
CONTROL CAMERA CONTROL
CAMERA CONTROL SYSTEM
TALLY
G/L
G/L  DC15V
OPTION
SWITCH 
CONTROL
PREVIEW
VIDEO
G/L
ONPOWER
OFFPOWER
O    I
FUSE(POWER)
3.15AFUSEFUSE
Option UnitSEG, Switcher etc.
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
ZOOM/FOCUS CONTROL
IRIS CONTROL
LAMPCONTROL
SPEED FOUCUS PA N  /  T I LT
ZOOMTELE
WIDEFA R
LEFT RIGHTUP
DOWN
NEAR
DEFON
OFF ON
OFF
POWEROPERATE
IRISCAM
CONT
BAR
CAMMODEGAIN AWC
SCENE
FILEABC
AT W
A
B
AUTO/AIWELC LOW MID
MANUON SC H
OFF HIGHT AGC
OFF 1 / 100SHUTTER
ON
OFF
LAMPMEMORY
ON
OFF AUTO
MANUON
OFFON
OFFON
OFF ON
OFFON
OFF
WIP
EXT ND OPH / F
1 .
2 .
3 .
4 .
G/L PHASE
PRESET
T.PEDMulti Hybrid Control Panel AW-RP505
154 3 2 154 3 2
2 1345
67891090¡  180¡
0¡     270¡
LEVELTALLYCONTROL
POWER
1
YC2
YC3
YC4
YC5
YC
OFF ON
CABLE  COMP
Multl  Port  Hub  AW-H8505
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
Signal Generator
Control Panel
AC Adaptor
AW-PS301 Pan/tilt Head AC
Adapter
AW-PS300 Halogen
LampColor Monitor
(75Wterminator)
Multi Hybrid Control Panel AW-RP505 Color Camera
WV-E550A
AW-E560
Camera Cable
AW-CA20T15
Multiport Hub
AW-HB505
Preview Color Monitor Servo Control
Zoom Lens
Unnecessary if no
halogen lamp is used. Unnecessary if
no optional unit is
connected.Multiport Hub
AC Adabtor
AW-PS505
• Example of System Configuration 
						

							-26-
OPERATING PROCEDURES1.Power
Press the power switch on each pan/tilt head AC
adapter and the power switch on the multiport hub AC
adapter to the ON position, then press the power
switch on the multiport hub to the ON position.  Finally,
press the power control switch on the multi hybrid con-
trol panel to the ON position.
2. Pan/tilt Limiter Setting for Each
Pan/tilt Heads
If there are obstacles around the pan/tilt head, set the
limiters to limit the operating range (pan left and right
ends, tilt up and down ends) of the pan/tilt head.
Note:The switches on the pan/tilt head have been pre-
set before shipment from the factory on the
assumption that the pan/tilt head would be sus-
pended from the ceiling.  If the pan/tilt head is
mounted on a board, for example, be sure to shift
the mounting direction switches on the pan/tilt
head.  Unless this is done, pan/tilt directions will be
reversed and pan/head operation limiter data can-
not be properly stored in the memory.  For details
on shifting these switches, refer to INSTALLATION
OF PAN/TILT HEAD at page 19 or the Operating
Instructions for Pan/tilt Head.qSelect a pan/tilt head with the CONTROL switch.
wLeft Panning Limiter
Turn the pan/tilt head to the desired left panning limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [1] and
[6] of PRESET Switch @8for 5 seconds or more.  When
the desired limit has been set, button [5] of PRESET
Switch @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [1] and
[6] of PRESET Switch @8again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch @8lights.
MEMORY
PRESET
2 1345
678910
Up tilting limiterPreset position selection switch
Left panning
limiterLights on
completion
of setting.
Preset
memory
switchLights on 
completion 
of resetting
Down tilting limiterRight panning 
limiter 
						

							-27-
eRight Panning Limiter
Turn the pan/tilt head to the desired right panning limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [4] and
[9] of PRESET Switch @8for 5 seconds or more.  When
the desired limit has been set, button [5] of PRESET
Switch @8lights.
To reset the limit, keep the MEMORY Switch @7
depressed, and simultaneously press buttons [4] and
[9] of PRESET Switch @8again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch @8lights.
rUp Tilting Limiter
Turn the pan/tilt head to the desired up tilting limit with
PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [2] and
[3] of PRESET Switch @8for 5 seconds or more.  When
the desired limit has been set, button [5] of PRESET
Switch @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [2] and
[3] of PRESET Switch @8again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch @8lights.
tDown Tilting Limiter
Turn the pan/tilt head to the desired down tilting limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [7] and[8] of PRESET Switch @8for 5 seconds or more.  When
the desired limit has been set, button [5] of PRESET
Switch @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [7] and
[8] of PRESET Switch @8again for 5 seconds or more.
When the set limit is reset, button [10] of PRESET
Switch @8lights.
ySelect the pan/tilt heads with the CONTROL switch,
one at a time, and set the operating range limiters of
each pan/tilt head.
3. Cable Compensation Settings,
Genlock, and Total Pedestal
Adjustments for Each Cameras and
Various Switch Settings1) After selecting a camera with the CONTROL Switch
@2, set the CAM CONT Switch rto the ON position.
Note:When the CAM CONT Switch ron the multi
hybrid control panel is set to the ON position, the
switch settings of the multi hybrid control panel are
sent to the camera to update its settings.  Do not
set the CAM CONT Switch rto the ON position
except when changing the camera settings.  If
another camera is selected with the CONTROL
Switch @2while the CAM CONT Switch ris in the 
						

							-28-
POWER
1
YC2
YC3
YC4
YC5
YC
OFF ON
CABLE  COMP
Multl  Port  Hub  AW-H8505
Waveform Monitor
Vector ScopeColor Monitor
(75Wtermination)CABLE COMP C Control  CABLE COMP Y Control 
Multiport Hub
AW-HB505
ON position, the settings of the selected camera
will be similarly changed.  Set the CAM CONT
Switch rback to the OFF position before chang-
ing one camera for another with the CONTROL
Switch @2.
2) Adjust the cable compensation, genlock, and total
pedestal of the selected camera.
• Cable Compensation
Signal degradation due to cable length between the multi-
port hub and the pan/tilt head can be compensated for.
qIf the cable length from the pan/tilt head to the multi-
port hub is longer than 300 meters, set the cable com-
pensation switch on the pan/tilt head to the ON posi-
tion.  For details, refer to INSTALLATION OF PAN/TILT
HEAD at page 19 or the Operating Instructions for
Pan/tilt Head.
wConnect a waveform monitor or a vectorscope to the
video output connector on the control panel for the
corresponding the camera pan/tilt head number ([1] to
[5]), set the video output connector on the multiport
hub, set the mode switch to the BAR position, then
observe the color bar signals.
eAdjust the Y (luminance) signal level with the CABLE
COMP Y control for the corresponding camera pan/tilt
head number ([1] to [5]), then adjust the CABLE
COMP Y control then adjust the C (chrominance) sig-
nal level with CABLE COMP C control. Repeat this untilthe video output of the multiport hub is adjusted as
shown in the figure below.
Note:Turning CABLE COMP Y control changes not
only the Y (luminance) signal level but also the
video signal levels as a whole.