Panasonic Projector PT-RW430UK User Manual
Have a look at the manual Panasonic Projector PT-RW430UK User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

Chapter 4 Settings — [PROJECTOR SETUP] menu ENGLISH - 91 2) Press the button. fThe [SECURITY PASSWORD] screen is displayed. 3) Enter a security password and press the button. 4) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. f [PROGRESS] is displayed while saving data. Note fThe image setting registered in [USER LOGO] is not saved. [LOAD ALL USER DATA] Load the various setting values saved as a backup in the built-in memory of the projector . 1) Press as to select [LOAD ALL USER DATA]. 2) Press the button. f The [SECURITY PASSWORD] screen is displayed. 3) Enter a security password and press the button. 4) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. Note f The projector will go into the standby status to reflect the setting values when [LOAD ALL USER DATA] is executed. [INITIALIZE] Return various setting values to their factory default settings. 1) Press as to select [INITIALIZE]. 2) Press the button. f The [SECURITY PASSWORD] screen is displayed. 3) Enter a security password and press the button. fThe [INITIALIZE] screen is displayed. 4) Press as to select an item to initialize. [ALL USER DATA] Returns all setting items including [ENTRY SIGNAL], [NETWORK SETUP], [E-mail set up], and [USER LOGO] to factory default settings. The projector will go into the standby status to reflect the setting values. [ENTRY SIGNAL] Deletes all the setting values saved for each input signal. To delete only a part of a registered signal, perform the procedure described in “Deleting the registered signal” ( x page 94). [NETWORK/E - MAIL]Returns [NETWORK SETUP] and [E-mail set up] to factory default settings. [LOGO IMAGE] Deletes the image registered in [USER LOGO]. 5) Press the button. 6) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. [SERVICE PASSWORD] This function is used by a service person.

Chapter 4 Settings — [TEST PATTERN] menu 92 - ENGLISH [TEST PATTERN] menu On the menu screen, select [TEST PATTERN] from the main menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fPress qw to switch. [TEST PATTERN] Display the test pattern built-in to the projector. Settings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing various adjustments. 1) Press qw to switch [TEST PATTERN]. fThe items will switch each time you press the button. Menu screen + All white Displays test patterns with the menu screen. Select a test pattern so that it is easy to make various adjustments. Menu screen + All black Menu screen + Window Menu screen + Window (inversion) Menu screen + Color bar (vertical) Menu screen + Color bar (horizontal) Menu screen + 16:9/4:3 aspect frame Menu screen + Focus Menu screen + Entry screen Displays the menu screen and input signal. Built-in test patterns are not displayed. Note f Press the button while the test pattern is displayed to hide the on-screen menu. fIf the on-screen display is hidden while displaying the test pattern, the test pattern is not switched even if qw are pressed. To switch the test pattern, operate with the on-screen displayed.

Chapter 4 Settings — [SIGNAL LIST] menu ENGLISH - 93 [SIGNAL LIST] menu On the menu screen, select [SIGNAL LIST] from the main menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. rRegistered signal details f A name can be set for each sub memory (x page 74). fMemory number: A1 (1-2) When the signal of the address number (A1, A2, ...L7, L8) is registered. Sub memory number Registering new signals After a new signal is input and the button on the remote control or the control panel is pressed, the registration is completed and the [MAIN MENU] screen is displayed. Note f Up to 96 signals, including sub memories, can be registered to the projector . fThere are 12 pages (eight memories of A through L, with eight memories possible on each page) for memory numbers, and the signal is registered to the lowest number that is available. If there is no available memory number it will be overwritten from the oldest signal. f The names to be registered are automatically determined by the input signals and memory numbers. fIf a menu is being displayed, the new signals will be registered at the instant they are input. Renaming the registered signal Registered signals can be renamed. 1) Press asqw to select the signal for which details are to be displayed. 2) Press the button. f The [REGISTERED SIGNAL STATUS] screen is displayed. fThe input signal name, memory number , input terminal, frequency, synchronization signal, etc., are displayed. fPress the button or the button to return to the [REGISTERED SIGNAL LIST] screen. 3) Press the button. fThe [RENAME] screen is displayed. 4) Press asqw to select the text, and press the button to enter the text. 5) After the name is changed, press asqw to select [OK], and press the button. fThe registration is completed and the [REGISTERED SIGNAL STATUS] screen returns. fWhen pressing asqw to select [CANCEL] and pressing the button, the changed signal name will not be registered and an automatically registered signal name will be used.

Chapter 4 Settings — [SIGNAL LIST] menu 94 - ENGLISH Deleting the registered signal Registered signals can be deleted. 1) Press asqw to select the signal to delete. 2) Press the button. fThe [ENTRY SIGNAL DELETE] screen is displayed. fT o cancel deletion, press the button or the button to return to the [REGISTERED SIGNAL LIST] screen. 3) Press the button. fThe selected signal will be deleted.

Chapter 4 Settings — [SECURITY] menu ENGLISH - 95 [SECURITY] menu On the menu screen, select [SECURITY] from the main menu, and select the\ item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fWhen the projector is used for the first time Initial password: Press awsqawsq in order , and press the button. fAfter selecting the item, press asqw to set. Attention fWhen you select the [SECURITY] menu and press the button, entering a password is required. Enter the preset password and then continue operations of the [SECURITY] menu. fWhen the password has been changed previously , enter the changed password, and press the button. Note fThe entered password is displayed with * mark on the screen. fAn error message is displayed on the screen when the entered password is incorrect. Re-enter the correct password. [SECURITY PASSWORD] The [SECURITY PASSWORD] screen is displayed when the power is turned on. If an incorrect password has been entered, operations other than the power button and the button are not available. 1) Press as to select [SECURITY PASSWORD]. 2) Press qw to switch [SECURITY PASSWORD]. fThe items will switch each time you press the button. [OFF] Disables the security password entry. [ON] Enables the security password entry. Note f[SECURITY PASSWORD] is set to [OFF] at the time of purchase or when [ALL USER DATA] has been initialized. fChange the password periodically that is hard to guess. fThe security password is enabled after setting [SECURITY PASSWORD] to [ON] and turning the switch to . [SECURITY PASSWORD CHANGE] Change the security password. 1) Press as to select [SECURITY PASSWORD CHANGE]. 2) Press the button. f The [SECURITY PASSWORD CHANGE] screen is displayed. 3) Press asqw and the number ( - ) buttons to set the password. fUp to eight button operations can be set. 4) Press the button. 5) Re-enter the password for the confirmation. 6) Press the button. Note f The entered password is displayed with * mark on the screen. fIf numbers have been used for the security password, the security password will need to be initialized again if the remote control is lost. Consult your dealer for the initialization method.

Chapter 4 Settings — [SECURITY] menu 96 - ENGLISH [TEXT DISPLAY] Overlap the security message (text) over the projected image. 1) Press as to select [TEXT DISPLAY]. 2) Press qw to switch [TEXT DISPLAY]. fThe items will switch each time you press the button. [OFF] Hides the security message. [ON] Displays the security message. Note fIf a closed caption signal of the selected mode is input, the security message is not displayed. [TEXT CHANGE] Change the text displayed when [TEXT DISPLAY] is set to [ON]. 1) Press as to select [TEXT CHANGE]. 2) Press the button. f The [TEXT CHANGE] screen is displayed. 3) Press asqw to select the text, and press the button to enter the text. fUp to 22 characters can be input. 4) Press asqw to select [OK], and press the button. fThe text is changed. [MENU LOCK] Display the menu with the button, and set whether to enable menu operations. 1) Press as to select [MENU LOCK]. 2) Press qw to switch [MENU LOCK]. fThe items will switch each time you press the button. [OFF] Cancels the lock on menu operations. [ON] Locks menu operations. Note fAfter setting [MENU LOCK] to [ON], the button cannot be operated if the incorrect password is input. f[MENU LOCK] is set to [OFF] at the time of purchase or when [ALL USER DA TA] has been initialized. fThe lock release is maintained until the projector enters standby . [MENU LOCK PASSWORD] Change the menu lock password. 1) Press as to select [MENU LOCK PASSWORD]. 2) Press the button. f The [MENU LOCK PASSWORD] screen is displayed. 3) Press asqw to select the text, and press the button to enter the text. fUp to 16 characters can be input. 4) Press asqw to select [OK], and press the button. fTo cancel, select [CANCEL]. Attention fThe initial password is “AAAA” at the time of purchase or when [ALL USER DA TA] has been initialized. fChange the password periodically that is hard to guess.

Chapter 4 Settings — [SECURITY] menu ENGLISH - 97 [CONTROL DEVICE SETUP] Enable/disable the button operations on the control panel and the remote control. 1) Press as to select [CONTROL DEVICE SETUP]. 2) Press the button. f The [CONTROL DEVICE SETUP] screen is displayed. 3) Press as to select [CONTROL PANEL] or [REMOTE CONTROL]. 4) Press the button. f The [CONTROL PANEL] screen or the [REMOTE CONTROL] screen is displayed. 5) Press as to select [ENABLE] or [DISABLE]. fYou can set the operation restriction from the control panel or the remote control. [ENABLE] Enables all button operations on the projector body or the remote control. [DISABLE] Disables all button operations on the projector body or the remote control. 6) Press the button. 7) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. Note f When a button operation is performed on the device set to [DISABLE], the [SECURITY PASSWORD] screen is displayed. To continue operations, enter the security password. f The [SECURITY PASSWORD] screen will disappear when the button is pressed, or when there is no operation for approximately ten seconds. f If the operations of both [CONTROL PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot enter standby). f When the setting has completed, the menu screen will disappear . To operate continuously, press the button to display the main menu.

Chapter 4 Settings — [NETWORK] menu 98 - ENGLISH [NETWORK] menu On the menu screen, select [NETWORK] from the main menu, and select the \ item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press asqw to set. [DIGITAL LINK MODE] Switch the communication method of the terminal of the projector. 1) Press as to select [DIGITAL LINK MODE]. 2) Press qw to switch [DIGITAL LINK MODE]. fThe items will switch each time you press the button. [AUTO] Switches the communication method automatically to DIGITAL LINK or Ethernet. [DIGITAL LINK] Fixes the communication method to DIGITAL LINK. [ETHERNET] Fixes the communication method to Ethernet. Possible communication modes Setting Communication possible HDMI Ethernet RS - 232C [AUTO] For DIGITAL LINK lll For Ethernet ― l― [DIGITAL LINK] lll [ETHERNET] ― l― l: Communication possible ―: Communication not possible [DIGITAL LINK SETUP] Set the communication method of DIGITAL LINK. When the projector is connected directly via Ethernet 1) Press as to select [DIGITAL LINK SETUP]. 2) Press the button. f The [DIGITAL LINK SETUP] screen is displayed. 3) Press as to select [DUPLEX(ETHERNET)]. 4) Press qw to switch the communication method. fThe items will switch each time you press the button. [AUTONEGOTIATION] The communication method is set automatically. [100BaseTX - Full]Full-duplex communication method is set. [100BaseTX - Half]Half-duplex communication method is set. 5) Press as to select [STORE]. 6) Press the button. 7) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button.

Chapter 4 Settings — [NETWORK] menu ENGLISH - 99 Note fThe projector does not support 10BaseT Full/Half. When the projector is connected to a twisted-pair-cable transmitter 1) Press as to select [DIGITAL LINK SETUP]. 2) Press the button. f The [DIGITAL LINK SETUP] screen is displayed. 3) Press as to select [DUPLEX(DIGITAL LINK)]. 4) Press qw to switch the communication method. fThe items will switch each time you press the button. [100BaseTX-Full] Full duplex communication method is set. [100BaseTX - Half]Half-duplex communication method is set. [AUTONEGOTIATION] The communication method is set automatically. 5) Press as to select [STORE]. 6) Press the button. 7) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. [DIGITAL LINK STATUS] Display DIGITAL LINK connection environment. 1) Press as to select [DIGITAL LINK STATUS]. 2) Press the button. f The [DIGITAL LINK STATUS] screen is displayed. [LINK STATUS] Either [NO LINK], [DIGITAL LINK], or [ETHERNET] is displayed. [HDMI STATUS] Either [NO HDMI], [HDMI ON], or [HDCP ON] is displayed. [SIGNAL QUALITY] [SIGNAL QUALITY] is a numerical value of the amount of error, and the display color changes to green, yellow, or red depending on that value. Check the signal quality level while receiving a signal from the twisted-pair-cable transmitter . fMAX/MIN: Maximum/minimum value of the amount of error . fGreen (-12 dB or lower) → Normal signal quality level. fY ellow ( -11 to -8 dB) → Warning level where there is the possibility of noise introduced on the screen. f Red (-7 dB or higher) → Abnormal level where synchronization may be interrupted, or a signal may not be received. [NETWORK SETUP] Perform the initial setting of the network before using the network function. 1) Press as to select [NETWORK SETUP]. 2) Press the button. f The [NETWORK SETUP] screen is displayed. 3) Press as to select an item, and change the settings according to the operation i\ nstructions of the menu. [PROJECTOR NAME] Change the setting when using a DHCP server. [DHCP] Set to [ON] when obtaining an IP address automatically using a DHCP server. Set to [OFF] when not using a DHCP server. [IP ADDRESS] Enter the IP address when not using a DHCP server. [SUBNET MASK] Enter the subnet mask when not using a DHCP server. [DEFAULT GATEWAY] Enter the default gateway address when not using a DHCP server. 4) Press as to select [STORE], and press the button.

Chapter 4 Settings — [NETWORK] menu 100 - ENGLISH 5) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. Note f When using a DHCP server, confirm that the DHCP server is running. fConsult your network administrator regarding the IP address, subnet mask, and default gateway. [NETWORK CONTROL] Set up the control method of the network. 1) Press as to select [NETWORK CONTROL]. 2) Press the button. f The [NETWORK CONTROL] screen is displayed. 3) Press as to select an item, and press qw to change the setting. [WEB CONTROL] Set to [ON] to control with the web browser. [PJLink CONTROL] Set to [ON] to control with the PJLink protocol. [COMMAND CONTROL] Set to [ON] when controlling the projector with the control command format ( x page 129) of the terminal. Refer to “Control commands via LAN” ( x page 125). [COMMAND PORT] Set the port number used for command control. [CRESTRON RoomView] Set to [ON] to control with RoomView of Crestron Electronics, Inc. [AMX D.D.] Set to [ON] to control with the controller of AMX Corporation. Setting this function to [ON] enables detection through “AMX Device Discovery”. For details, refer to the website of AMX Corporation. URL http://www.amx.com/ [EXTRON XTP] Set to [ON] when connecting the “XTP transmitter” of Extron Electronics to the terminal. [EXTRON XTP] must be set to [OFF] when connecting the optional digital interface box (Model No.: ET - YFB100G). For details of the “XTP transmitter”, refer to the website of Extron Electronics. URL http://www.extron.com/ [STORE] Save the current network control settings. 4) Press as to select [STORE], and press the button. 5) When the confirmation is displayed, select [OK] or [CANCEL], and press t\ he button. [NETWORK STATUS] Display the status of the projector network. 1) Press as to select [NETWORK STATUS]. 2) Press the button. f The [NETWORK STATUS] screen is displayed. Network connections The projector has a network function, and the following operations are available from the computer using the web control. fSetting and adjustment of the projector fDisplay of the projector status fSending of E-mail messages when there is a problem with the projector The projector supports “Crestron RoomV iew”, and the following application software of Crestron Electronics, Inc. can be used. fRoomV iew Express fFusion R V fRoomV iew Server Edition Attention fConnect the LAN to indoor devices.