Panasonic Projector PT-RW430UK User Manual

							Chapter 6 Appendix — Technical information
ENGLISH - 131
ModeResolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) Format Plug and play
*1
Horizontal
(kHz)Vertical(Hz)1 2
3EDID1 EDID2 EDID3
SXGA 1   280   x   1   024 64.0 60.0 108.0
R/D/H
l―
l l l
1   280   x   1   024 80.0 75.0 135.0 R/D/H
l―
l l l
1
  280   x   1   024 91.1 85.0 157.5 R/D/H ― ― ― ― ―
SXGA+ 1
  400   x   1   050 65.2 60.0 122.6 R/D/H
l―
l l l
1
  400   x   1   050 65.3 60.0 121.8 R/D/H ― ― ― ― ―
1
  400   x   1   050 82.2 75.0 155.9 R/D/H ― ― ― ― ―
UXGA 1
  600   x   1   200 75.0 60.0 162.0 R/D/H
l―
l l l
1280
  x   720 1
  280   x   720 37.1 49.8 60.5 R/D/H ― ― ― ― ―
1
  280   x   720 44.8 59.9 74.5 R/D/H ― ― ― ― ―
1
  280   x   720 92.6 120.0 161.0 R/D/H ― ― ― ― ―
1280
  x   768 1
  280   x   768 39.6 49.9 65.3 R/D/H ― ― ― ― ―
1
  280   x   768 47.8 59.9 79.5 R/D/H ― ― ― ― ―
1280
  x   800 1
  280   x   800 41.3 50.0 68.0 R/D/H ― ― ― ― ―
1
  280   x   800 49.7 59.8 83.5 R/D/H ― ― ― ― ―
WXGA+ 1
  440   x   900 55.9 59.9 106.5 R/D/H ― ― ― ― ―
WSXGA+ 1
  680   x   1   050 65.3 60.0 146.3 R/D/H ― ― ― ― ―
1920
  x   1080 1   920   x   1   080
*366.6 59.9 138.5 R/D/H ― ― ― ― ―
WUXGA 1
 
920
 
x
 
1
 
200
*374.0 60.0 154.0 R/D/H
l―
l l l
*1 Signals with  l  in the Plug and play columns are signals described in EDID (extended display identification data) of the projector . A signal, which 
has no l in the Plug and play columns but has an entry in the Format column, can be input. For signals without  l in the Plug and play columns, 
resolution may not be selected in the computer even though the projector supports them.
*2
 
When a 1
 125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*3
 
VESA
  CVT-RB (Reduced Blanking)-compliant
Note
 fThe number of display dots is 1   920   x   1   080 for the PT- RZ470U series, and 1   280   x   800 for the PT- RW430U series. A signal with a different 
resolution is converted to the number of display dots.
 f The “i” at the end of the resolution indicates an interlaced signal. fWhen interlaced signals are connected, flickering may occur on the projected image. fDIGIT

AL LINK input compatible signal is the same as HDMI input compatible signal.  
						

							Chapter 6 Appendix — Technical information
132 - ENGLISH
List of 3D compatible signals
The following table specifies the types of 3D video signals compatible with the projector.
Items that are applicable to  1 to 4 in the table are as follows.
1
 
Frame packing system
2

 
Side by side system
3

 
T
 op and bottom system
4
 
Frame sequential system
3D compatible signal Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) HDMI
DVI - I
COMPUTER
Horizontal
(kHz)Vertical(Hz)1 2 3 2*13*14*24
750 (720)/60p 1
 
280
 
x
 
720 45.0 60.0 74.3 l
*3l l*3l*4l*5― ―
750 (720)/50p 1
 
280
 
x
 
720 37.5 50.0 74.3 l
*3l*4l*3l*4l*5― ―
1125 (1080)/60i 1
 
920
 
x
 
1
 
080i 33.8 60.0 74.3 ― l
*3―l*4― ― ―
1125 (1080)/50i 1
 
920
 
x
 
1
 
080i 28.1 50.0 74.3 ― l
*3―l*4― ― ―
1125 (1080)/24p 1
 
920
 
x
 
1
 
080 27.0 24.0 74.3 l
*3l l*3l*4l*5― ―
1125 (1080)/60p 1
 
920
 
x
 
1
 
080 67.5 60.0 148.5 ― l―
l
*4― ― ―
1125 (1080)/50p 1
 
920
 
x
 
1
 
080 56.3 50.0 148.5 ― l
*4―l*4― ― ―
XGA 1
 
024
 
x
 
768 80.0 100.0 105.0 ― ― ― ― ― l
*6l*6
1 024 x 768 99.0 119.8 137.8 ― ― ― ― ―
l*6l*6
1280 x 7201   280   x   720 92.6 120.0 161.6 ― ― ― ― ―
l*6l*6
*1 Supports only DVI digital signals.
*2  Supports DVI digital signals/DVI analog signals.
*3
 
HDMI-standard 3D Mandatory format signals
*4

 
3D images can be displayed by setting [3D INPUT
  FORMAT] to [SIDE BY SIDE].
*5
 
3D images can be displayed by setting [3D INPUT
  FORMAT] to [TOP AND BOTTOM].
*6
 
3D images can be displayed by setting [3D INPUT
  FORMAT] to [FRAME SEQUENTIAL].
Note
 f3D compatible signals for DIGIT AL LINK input are the same as compatible signals for HDMI input.  
						

							Chapter 6 Appendix — Specifications
ENGLISH - 133
Specifications
The following table describes the specifications of the projector.
Model No.PT- RZ470UK/PT- RZ470UWPT- RW430UK/PT- RW430UW
Power supply AC
  100   V - 240   V 50   Hz/60   Hz
Power consumption 460
  W (5.2  
A
  - 2.0  
A)
0.5

  W when [STANDBY MODE] is set to [ECO]
8
  W when [STANDBY MODE] is set to [NORMAL] (when fan is stopped)
DLP chip Panel size
16.5
  mm (0.65") (aspect ratio 16:9) 16.5
  mm (0.65") (aspect ratio 16:10)
Display system 1-unit DLP chip, DLP type
Number of pixels 2
  073   600 pixels
(1
  920   x   1   080 dots)1
  024   000 pixels
(1
  280   x   800 dots)
Lens Zoom
1.5 to 2.9:1 1.5 to 3.1:1
Focus F = 2.0 to 3.4
f = 21.5
  mm to 43.0   mm
Light source Hybrid light source (LED/laser diode)
Light output
*13 500 lm (ANSI)
Contrast ratio
*120 000:1
Applicable 
scanning 
frequency
*2
For video signal Horizontal: 15.75   kHz/15.63   kHz, Vertical: 50   Hz/60   Hz
For RGB signal Horizontal: 15
  kHz to 100   kHz, Vertical: 24   Hz to 120   Hz
PIAS (Panasonic Intelligent Auto Scanning) system
Dot clock frequency162
  MHz or lower
For YC
BCR/YPBPR 
signal
 f 525i (480i)
Horizontal: 15.75
   kHz, Vertical: 60   Hz
 f
525p (480p)
Horizontal: 31.5
   kHz, Vertical: 60   Hz
 f
750 (720)/60p
Horizontal: 45
   kHz, Vertical: 60   Hz
 f
1
 125 (1035)/60i
Horizontal: 33.75   kHz, Vertical: 60   Hz
 f
1

125 (1080)/50i
Horizontal: 28.13
  kHz, Vertical: 50   Hz
 f1

125 (1080)/24sF
Horizontal: 27
  kHz, Vertical: 48   Hz
 f1

125 (1080)/30p
Horizontal: 33.75
  kHz, Vertical: 30   Hz
 f1

125 (1080)/50p
Horizontal: 56.25
  kHz, Vertical: 50   Hz
 f625i (576i)
Horizontal: 15.63
   kHz, Vertical: 50   Hz
 f
625p (576p)
Horizontal: 31.25
   kHz, Vertical: 50   Hz
 f
750 (720)/50p
Horizontal: 37.5
   kHz, Vertical: 50   Hz
 f
1
 125 (1080)/60i
Horizontal: 33.75   kHz, Vertical: 60   Hz
 f
1

125 (1080)/24p
Horizontal: 27
  kHz, Vertical: 24   Hz
 f1

125 (1080)/25p
Horizontal: 28.13
  kHz, Vertical: 25   Hz
 f1

125 (1080)/60p
Horizontal: 67.5
  kHz, Vertical: 60   Hz
For DVI
-
D signal 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 
 
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 f Displayable resolution: VGA

 to WUXGA (non-interlaced)
WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.
 f Dot clock frequency: 25

  MHz to 162   MHz
For HDMI signal 525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p, 
 
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p
 f Displayable resolution: VGA

 to WUXGA (non-interlaced)
WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.
 f Dot clock frequency: 25

  MHz to 162   MHz
*1 Measurement, measuring conditions and method of notation all comply with ISO21 1 18 international standards.
*2  Refer to “List of compatible signals” ( x
  page   130) for the types of video signals that can be used with the projector .  
						

							Chapter 6 Appendix — Specifications
134 - ENGLISH
Model No.PT- RZ470UK/PT- RZ470UWPT- RW430UK/PT- RW430UW
Color system 7 standards (NTSC/NTSC4.43/PAL/PAL
- N/PAL - M/SECAM/PAL60)
Projection screen size 1.02 m (40") to 7.62 m (300")
Screen aspect ratio 16:916:10
Projection method [FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Terminal  
terminal
1 set, high-density D
- Sub 15   p (female)
RGB signal 0.7
  V [p-p] 75   Ω (SYNC ON GREEN: 1.0   V [p-p] 75   Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
(SYNC/HD and VD do not support 3 value SYNC.)
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 
terminal 1 set, DVI
-
I 29
 
p
Digital signal Single link, DVI 1.0 compliant, HDCP compatible
RGB signal 0.7
 
V [p-p] 75
 
Ω (SYNC ON GREEN: 1.0
 
V [p-p] 75
 
Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 
terminal 1 set, HDMI 19 pin, HDCP
 compatible, Deep Color compatible
Audio signal Linear PCM (Sampling frequency: 48
 
kHz/44.1
 
kHz/32   kHz)
 
terminal 1 set, Pin jack 1.0
 
V [p-p] 75
 
Ω
 
terminal D
-
Sub 9
 
p, 1 set, RS
-
232C compliant, for computer control
 
terminal 1 set, M3 stereo mini jack (monitor output, with stereo support) 0
 
V [rms] to 1.8
  V [rms] (variable), output 
impedance 2.2
 
kΩ or lower
 
terminal 1 set, M3 stereo mini jack 0.5
 
V [rms], input impedance 22
 
kΩ or higher
 terminal 1 set, for RJ
-
45 network, DIGITAL LINK connection, PJLink compatible, 100Base - TX
 
terminal 1 set, Mini DIN 3
 
p, for 3D IR transmitter connection
Power cable length 3.0
 
m (118-1/8")
Outer case Molded plastic
Dimensions Width: 455
 
mm (17-29/32")
Height: 137
 
mm (5-13/32") (with minimum feet length)
Depth: 415
 
mm (16-11/32") (including lens)
Weight Approx. 11
 
k] (24.3
 
lbs.)
*1
Noise level*2When [LIGHT POWER] is set to [NORMAL]: 35 dB
When [LIGHT  POWER] is set to [LOW]: 29   dB
Operating environment Operating environment temperature
*3: 0 °C (32 °F) to 45 °C (113 °F)
Operating environment humidity: 20
  % to 80   % (no condensation)
Remote 
control Power supply
DC 3
 
V (AA/R6/LR6 battery x 2)
Operating range Within 15
 
m (49'2") (when operated directly in front of signal receiver)
Weight 117
 
] (4.1
 
ozs.) (including batteries)
Dimensions Width: 48
 
mm (1-7/8"), Height: 163
 
mm (6-13/32"), Depth: 24.5   mm (31/32")
*1 Average value. Weight varies for each product.
*2 Measurement, measuring conditions and method of notation all comply with ISO21 1
18 international standards.
*3
 
When using the projector at high altitudes (1
   400   m (4   593') – 2   700   m (8   858') above sea level), the operating environment temperature will be 0   °C 
(32
  °F) – 40   °C (104   °F). When the ambient temperature becomes 35   °C (95   °F) or higher, the output light may be reduced to protect the projector.
Note
 fThe model numbers of accessories and optional components are subject to change without notice.  
						

							Chapter 6 Appendix — Dimensions
ENGLISH - 135
Dimensions
Unit: mm
409 (16-3/32)
415 (16-11/32)
455 (17-29/32)
63.5 (2-1/2)
72 (2-27/32)
72 (2-27/32)
63.5 (2-1/2)
137 (5-13/32)
128.5 (5-1/16)125 (4-29/32)
* Actual dimensions may dif fer depending on the product.  
						

							Chapter 6 Appendix — Ceiling mount bracket safeguards
136 - ENGLISH
Ceiling mount bracket safeguards
 fWhen installing the projector to a ceiling, be sure to use the specified ceiling mount bracket (Model No.: ET- PKR100H (for high ceilings), 
ET- PKR100S (for low ceilings), ET- PKR100P (for portrait)).
 fWhen installing the projector

, attach the drop-prevention kit included with the ceiling mount bracket.
 fAsk a qualified technician to do the installation work such as mounting the projector on the ceiling.
 fPanasonic takes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not manufactured by 
Panasonic or the inappropriate choice of location for installation, even if the warranty period of the projector has not expired.
 fUnused products must be removed promptly by a qualified technician.
 fUse a torque screwdriver or 

Allen torque wrench to tighten bolts to their specified tightening torques. Do not use electric screwdrivers or 
impact screwdrivers.
 f For details, read the installation manual that comes with the ceiling mount bracket.
 fThe model numbers of accessories and optional components are subject to change without notice.


M4
10 mm (13/32)
Bottom view
Model No. of ceiling mount bracket: ET-PKR100H (for high ceilings)
ET-PKR100S (for low ceilings)
ET-PKR100P (for portrait)
Torque: 1.25 ± 0.2 N·m  
						

							Index
ENGLISH - 137
0 – 9[3D INPUT FORMAT]     6 5
[3D MODE]
     6 4
[3D SAFETY
 PRECAUTIONS]
     6 6
[3D SETTINGS]
     47,   64
AAccessories    1 9
 terminal
     2 2
Adjusting adjustable feet
     2 8
Adjusting the volume
     4 2
[ADV
ANCED MENU]
     46,   58
[ASPECT]
     5 5
[AUDIO SETTING]
     8 8
[AUT
O SETUP]
     6 9
 button
Remote control
    
 21,   41
Auto setup function
     4 1
[AUT
O SIGNAL]
     6 9
[A
V MUTE]
     7 5
 button Remote control
    
 21,   40
AV mute function
     4 0
B[BACK COLOR]    7 4
[BLANKING]
     5 8
[BRIGHTNESS]
     5 0
[BRIGHTNESS CONTROL]
     7 9
CCautions on use      1 8
Cautions when installing
     1 5
Cautions when transporting
     1 5
Ceiling mount bracket
     136
Ceiling mount bracket safeguards
     136
[CLAMP
 POSITION]
     5 9
[CLOCK PHASE]
     5 6
[CLOSED CAPTION SETTING]
     7 3
[COLOR]
     5 0
[COLOR MA
TCHING]
     6 7
[COLOR 
TEMPERATURE]
     5 0
 button Remote control
    
 21,   41
[COMPUTER IN]
     6 9
Connecting the power cord
     3 4
Connecting to a twisted-pair-cable transmitter
     101
Connection
     2 9
[CONTRAST]
     4 9
[CONTROL
 DEVICE SETUP]
     9 7
[COOLING CONDITION]
     7 7
Crestron RoomV
iew
     100,   115
D[DATE AND TIME]    9 0
[DA
YLIGHT VIEW]
     5 2
 button
Remote control
    
 21,   45
Deleting the registered signal
     9 4
[DIGIT
AL CINEMA REALITY]
     5 8
DIGIT
AL LINK
     18,   117
 button Remote control
    
 21,   41
[DIGITAL LINK IN]
     7 1
[DIGIT
AL LINK INPUT]
     8 5
[DIGIT
AL LINK MODE]
     9 8
[DIGIT
AL LINK SETUP]
     9 8
[DIGIT
AL LINK STATUS]
     9 9
Dimensions
     135
Display language
     47,   63
[DISPLAY OPTION]
     47,   67
Disposal
     1 8
 button Remote control
    
 21,   41
[DVI-I IN]
     7 0
E button
Remote control     21,   42
[ECO MANAGEMENT]
     7 7
[EDGE BLENDING]
     5 9
 button Projector body
    
 2 3
Remote control
     2 1
F[FRAME RESPONSE]    6 1
[FREEZE]
     7 5  button
Remote control  
  
 21,   40
Freeze function
     4 0
 -  buttons Remote control
    
 21,   42
Function button
     4 2
[FUNCTION BUTT
ON]
     8 7
H button
Remote control     21,   41
[HDMI IN]
     7 1
[HIGH 
ALTITUDE MODE]
     7 7
I button
Remote control     21,   24
 button Remote control
    
 21,   24
[INITIALIZE]
     9 1
Initial setting
     2 0
[INITIAL
 STARTUP]
     8 5
[INPUT
 RESOLUTION]
     5 9
 button
Projector body
    
 23,   41
K[KEYSTONE]    5 7
L[LEFT/RIGHT SWAP]     6 4
Light source indicator
     11 9
List of compatible signals
     130
[LOAD 
ALL USER DATA]
     9 1
MMain menu     4 5
Main power switch
     22,   35
Maintenance
     120
 button Projector body
    
 2 3
Remote control
     2 1
Menu item
     4 6
[MENU LOCK]
     9 6
[MENU LOCK P
ASSWORD]
     9 6
NNavigating through the menu     4 4
[NETWORK]
     48,   98
Network connections
     100
[NETWORK CONTROL]
     100
[NETWORK SETUP]
     9 9
[NETWORK ST
ATUS]
     100
[NOISE REDUCTION]
     5 2
O[ON-SCREEN DISPLAY]     7 1
On-screen menu
     4 4
Optional accessories
     1 9
P[PICTURE]    46,   49
[PICTURE MODE]
     4 9
[POSITION]
     46,   54
Power button Projector body
    
 2 3
Remote control
     2 1
Power cord
     3 4
Power indicator 
     3 4
Precautions for use
     1 5
Projecting
     3 7
[PROJECTION METHOD]
     26,   76
[PROJECTOR ID]
     7 6
[PROJECT
OR SETUP]
     47,   76
R[RASTER POSITION]    6 2
Read this first!
     2
Registering new signals
     9 3
Remote control
     2 1
Remote control operations
     4 0
Renaming the registered signal
     9 3
Resetting to the factory default
     4 5
 button Projector body
    
 2 3
Remote control
     2 1
RoomV
iew
     11 5
[RS-232C]
     86,   127
S[SAFETY PRECAUTIONS MESSAGE]    6 5
[SA
VE ALL USER DATA]
    9 0
[SCHEDULE]
    8 3
[SCREEN SETTING]
    6 8
Security
    1 7
[SECURITY]
    48,   95
[SECURITY PASSWORD]
    9 5
[SECURITY
 PASSWORD CHANGE]
     9 5
Selecting the input signal
    3 7
 terminal
    127
[SER
VICE PASSWORD]
    9 1
Setting remote control ID numbers
     2 4
Setting up
    2 6
[SHARPNESS]
    5 2
[SHIFT]
    5 4
[SIGNAL
 LIST]
    48,   93
Specifications
    133
sRGB-compliant video
    5 3
[ST
ARTUP INPUT SELECT]
     8 5
[ST
ARTUP LOGO]
    7 4
[ST
ATUS]
    8 9
[SUB MEMOR
Y LIST]
    7 4
Switching of
f the projector
    3 6
Switching on the projector
    3 5
Switching the input signal
    4 1
[SYSTEM SELECT
OR]
    5 3
TTemperature indicator     11 9
[TEST
 PATTERN]
    48,   92
[TEXT CHANGE]
    9 6
[TEXT
 DISPLAY]
    9 6
[TINT]
    5 0
T
roubleshooting
    121
V button Remote control     21,  41
/ button Remote control
 
   21,   42
Z[ZOOM]    5 5
Index   
						

							Panasonic System Communications Company of North America
5th Floor, Two Riverfront Plaza, Newark, NJ 07102-5490
TEL: (877) 803 - 8492
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
TEL: (905) 624 - 5010
Panasonic Corporation
Web Site : http://panasonic.net/avc/projector/
© Panasonic Corporation 2013
W0113NS2103 -YI
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the 
correct method of disposal.