Panasonic Projector PT-RX110 User Manual

							Chapter 4 Settings — [POSITION] menu
ENGLISH - 91
When [ASPECT] is set to [DEFAULT]
1) Press as to select [ZOOM].
2)  
Press the  button.
 fThe 

[ZOOM] screen is displayed.
3)
 
Press 
 as to select [MODE].
4)
 
Press 
 qw to switch the item.
[INTERNAL] Enlarges the size within the aspect range set with [SCREEN FORMA T].
[FULL] Enlarges or reduces the size using the entire display area set with [SCREEN FORMA T].
5) Press as to select [INTERLOCKED].
6)  
Press 
 qw to switch the item.
[OFF] Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.
[ON] Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the 
same magnification.
7) Press 
as to select [VERTICAL] or [HORIZONTAL].
 fIf [ON] is selected, select [BOTH].
8)

 
Press 
 qw to adjust.
Note
 f When the [POSITION] menu  →  [ASPECT] is set to anything other than [DEFAULT], [MODE] is not displayed.
[CLOCK PHASE]
You can adjust the image to achieve an optimal image when there is a flickering image or smeared outlines.
1)
 
Press 
 as to select [CLOCK PHASE].
2)
 
Press 
 qw or the  button.
 fThe 

[CLOCK PHASE] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust.
 fAdjustment value will change between [0] and [+31]. 

Adjust the image so that the amount of interference is 
at a minimum.
Note
 f Adjustment may not be possible depending on the signal. fThere may be no optimal value if the output from the input computer is unstable. fThere may be no optimal value when the total dot number is shifted. f[CLOCK PHASE] can be adjusted only when 

YC
BCR/YPBPR signal or RGB signal is input to the  terminal or the  
terminal.
 f [CLOCK PHASE] cannot be adjusted when a digital signal is input. fThe adjustment value will change to [0] when  w

 is pressed while it was at [+31]. Also, the adjustment value will change to [+31] when  q is 
pressed while it was at [0].
[GEOMETRY]
You can correct various types of distortion in a projected image.
Unique image processing technology enables projection of a square image on a special screen shape.
1)
 
Press 
 as to select [GEOMETRY].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not perform geometric adjustment.
[KEYSTONE] Adjusts any trapezoidal distortion in the projected image.
[CORNER CORRECTION] Adjusts any distortion in the four corners of the projected image.  
						

							Chapter 4 Settings — [POSITION] menu
92 - ENGLISH
[CURVED CORRECTION]Adjusts any curved distortion in the projected image.
[PC-1]
*1
Performs geometric adjustment using a computer.
[PC-2]*1
[PC-3]*1
*1 Only for PT- RZ970.
Advanced skills are necessary to use a computer to control geometric adjustment. Consult your dealer . Up to three geometric adjustments 
performed using the computer can be saved.
Setting [KEYSTONE] or [CURVED CORRECTION]
1) Press  as to select [GEOMETRY].
2)  
Press 
 qw to select [KEYSTONE] or [CURVED CORRECTION].
3)
 
Press the  button.
 fThe 

[GEOMETRY:KEYSTONE] or [GEOMETRY:CURVED CORRECTION] screen is displayed.
4)
 
Press 
 as to select the item to adjust.
5)
 
Press 
 qw to adjust.
[KEYSTONE]
[LENS THROW RATIO]
Set the throw ratio.
Select the value close to the actual projection distance divided by projected image width here.
[VERTICAL KEYSTONE]
[HORIZONTAL KEYSTONE]
[VERTICAL BALANCE][HORIZONTAL BALANCE]
Adjust the setting according to the lens shift range in the vertical 
direction. Adjust the setting according to the lens shift range in the horizontal 
direction.
[CURVED CORRECTION]
[LENS THROW RATIO]
Set the throw ratio.
Select the value close to the actual projection distance divided by projected image width here.
[VERTICAL KEYSTONE]
[HORIZONTAL KEYSTONE]
[VERTICAL ARC][HORIZONTAL ARC]  
						

							Chapter 4 Settings — [POSITION] menu
ENGLISH - 93
[CURVED CORRECTION]
[VERTICAL BALANCE]
[HORIZONTAL BALANCE]
[MAINTAIN ASPECT RATIO]
Select [ON] to correct while keeping the aspect ratio.
Setting [CORNER CORRECTION]
1) Press  as to select [GEOMETRY].
2)  
Press 
 qw to select [CORNER CORRECTION].
3)
 
Press the  button.
 fThe 

[GEOMETRY:CORNER CORRECTION] screen is displayed.
4)
 
Press 
 as to select the item to adjust, and press the  button.
5)
 
Press 
 asqw to adjust.
[CORNER CORRECTION]
[UPPER LEFT]
[UPPER RIGHT][LOWER LEFT][LOWER RIGHT]
[LINEARITY]
Horizontal direction
Vertical direction
Note
 f The menu or logo may run of f the screen when [GEOMETRY] is set. fThe edge blending adjustment may not be performed correctly depending on the environment when using the [ADV ANCED MENU] menu →
 
[EDGE BLENDING] and [GEOMETRY] simultaneously.
 f The optional Upgrade Kit (Model No.: ET-

UK20) can be used to expand the correctable range. To purchase the product, consult your dealer. 
(Only for PT
-

RZ970)
 fThe 

[GEOMETRY] setting becomes disabled when the [DISPLAY OPTION] menu  → [IMAGE ROTATION] is set to anything other than [OFF] 
while using PT
-

RW930 or PT
-
 RX110, disallowing the usage of the geometric adjustment function.
 fThe settings for [DEF

AULT] and [USER] in the [PICTURE] menu → [GAMMA] become disabled when [GEOMETRY] is set to anything other 
than [OFF] while using PT
-

RW930 or PT
-
 RX110. The gamma mode will be the same as when set to [2.2].
 fThe image may disappear momentarily during adjustment, but this is not a malfunction.  
						

							Chapter 4 Settings — [ADVANCED MENU] menu
94 - ENGLISH
[ADVANCED MENU] menu
On the menu screen, select [ADVANCED MENU] from the main menu, and select an item from the sub‑
menu.
Refer to “Navigating through the menu” (x

  page   76) for the operation of the menu screen.
[DIGITAL CINEMA REALITY]
The picture quality is enhanced by raising the vertical resolution higher performing the cinema processing when 
576/50i signal for PAL (or SECAM), or 480/60i, 1080/50i, or 1080/60i signal for NTSC is input.
1)
 
Press 
 as to select [DIGITAL CINEMA REALITY].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically detects the signal and performs the cinema processing. (Factory default setting)
[OFF] Does not perform cinema processing.
[30p FIXED] When 480/60i or 1080/60i 
signal is input
Performs forced cinema processing (2:2 pulldown).
[25p FIXED] When 576/50i or 1080/50i 
signal is input
Note
 f
In [DIGITAL CINEMA REALITY], the picture quality will degrade when a signal other than the 2:2 pulldown is set as [25p FIXED] or [30p 
FIXED]. (Vertical resolution will degrade.)
 f When the [ADV

ANCED MENU] menu → [FRAME RESPONSE] is set to [FAST], [DIGITAL CINEMA REALITY] cannot be set.
[BLANKING]
You can adjust the blanking width if there are noises at the edge of the screen or the image is slightly running out 
from the screen while an image from the VCR or other devices are projected.
1)
 
Press 
 as to select [BLANKING].
2)
 
Press the  button.
 fThe 

[BLANKING] adjustment screen is displayed.
3)
 
Press 
 as to select [UPPER], [LOWER], [LEFT], or [RIGHT].
 fThe blanking width can be adjusted to arbitrary shape using a computer when [CUST OM MASKING] is set 
to anything other than [OFF] ([PC-1], [PC-2], or [PC-3]). Up to three blanking settings adjusted using the 
computer can be saved. (Only for PT
-

RZ970)
To use the [CUSTOM MASKING] function, the optional Upgrade Kit (Model No.: ET
-

UK20) is required. To 
purchase the product, consult your dealer.
4)
 
Press 
 qw to adjust the blanking width.
Blanking correction Item Operation AdjustmentRange of adjustment
Top of the screen [UPPER] Press q.
The blanking zone 
moves upward.
PT-
RZ970: Top and bottom 
0 - 599
PT
-

RW930: Top and bottom  0 - 399
PT
-

RX110: Top and bottom  0 - 383
Press w.
The blanking zone 
moves downward.
Bottom of the  screen [LOWER]Press w.
The blanking zone 
moves upward.
Press q.The blanking zone 
moves downward.  
						

							Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 95
Blanking correction Item OperationAdjustmentRange of adjustment
Left side of the  screen [LEFT]Press w.
The blanking zone 
moves to the right.
PT-
RZ970: Left and right 
0 - 959
PT
-

RW930: Left and right  0 - 639
PT
-

RX110: Left and right  0 - 511
Press q.
The blanking zone 
moves to the left.
Right side of the  screen [RIGHT]Press q.
The blanking zone 
moves to the right.
Press w.The blanking zone 
moves to the left.
[INPUT RESOLUTION]
You can adjust the image to achieve an optimal image when there is a flickering image or smeared outlines.
1)
 
Press 
 as to select [INPUT RESOLUTION].
2)
 
Press the  button.
 fThe 

[INPUT RESOLUTION]  screen is displayed.
3)
 
Press 
 as to select [TOTAL DOTS], [DISPLAY DOTS], [TOTAL LINES], or [DISPLAY LINES], and press 
qw to adjust each item.
 f V

alues corresponding to the signal being input are displayed automatically for each item. Increase or 
decrease the displayed values and adjust to the optimal point while viewing the screen if there are vertical 
stripes or sections are missing from the screen.
Note
 f Previously mentioned vertical banding will not occur with all white signal input. fImage may be disrupted during automatic adjustment, but this is not a malfunction. f[INPUT

 RESOLUTION] can be adjusted only when an RGB signal is input to the  terminal or the  terminal.
 fAdjustment may not be possible depending on the signal.
[CLAMP POSITION]
You can adjust the optimal point when the black part of the image is blunt or it has turned green.
1)
 
Press 
 as to select [CLAMP POSITION].
2)
 
Press 
 qw to adjust.
Status Rough guide for optimal value Range of adjustment
The black part is blunt. The point where bluntness of the black part improves the most is 
the optimal value.
1 - 255
The black part is green. The point where the green part becomes black, and the bluntness 
has improved is the optimal value.
Note
 f
[CLAMP POSITION] can be adjusted only when a signal is input to the  terminal or the  terminal. fAdjustment may not be possible depending on the signal.
[EDGE BLENDING]
The edge blending function allows multiple images to be seamlessly overlapped by using the inclination of the 
brightness at the overlapped area.
1)
 
Press 
 as to select [EDGE BLENDING].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Sets the edge blending function to off.
[ON] Use the setting value preset in the projector for the inclination of the edge blending area.  
						

							Chapter 4 Settings — [ADVANCED MENU] menu
96 - ENGLISH
[USER]Use the user-setting value for the inclination of the edge blending area. (Configuration/registration 
requires separate software. Consult your dealer.)
 f
Proceed to Step  3) when anything other than [OFF] is selected.
3)
 
Press the  button.
 f The 

[EDGE BLENDING] screen is displayed.
4)
 
Press 
 as to specify the location to be corrected.
 fWhen joining at top: Set [UPPER] to [ON]
 fWhen joining at bottom: Set [LOWER] to [ON]
 fWhen joining at left: Set [LEFT] to [ON]
 fWhen joining at right: Set [RIGHT] to [ON]
5)

 
Press 
 qw to switch to [ON].
6)
 
Press 
 as to select [START] or [WIDTH].
7)
 
Press 
 qw to adjust the starting position or correction width.
8)
 
Press 
 as to select [MARKER].
9)
 
Press 
 qw to switch to [ON].
 fA

 marker for image position adjustment is displayed. The position where the red and green lines overlap for 
the projectors to be joined will be the optimal point. Make sure to set the correction width for the projectors 
to be joined with the same value. Optimal joining is not possible with projectors that have dif ferent 
correction widths.
The optimal point is the point at which these lines overlap.
Green lineRed line
10) Press  as to select [BRIGHTNESS ADJUST].
11)  
Press the  button.
 fThe 

[BRIGHTNESS ADJUST] screen is displayed.
 fBy setting [AUT

O TESTPATTERN] to [ON] on the  [EDGE BLENDING] screen, the black test pattern is 
displayed when you enter the  [BRIGHTNESS ADJUST] screen.
12)
 
Press 
 as to select [NON-OVERLAPPED BLACK LEVEL].
13)
 
Press the  button.
 fThe 

[NON-OVERLAPPED BLACK LEVEL] screen is displayed.
 f[RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].
14)

 
Press 
 as to select an item, and press qw to adjust the setting.
 fOnce the adjustment is completed, press the  button to return to the  [BRIGHTNESS ADJUST]

 
screen.
15)
 
Press 
 as to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH].
16)
 
Press 
 qw to set the region (width) of the [BLACK BORDER WIDTH] adjustment.
17)
 
Press 
 as to select [UPPER KEYSTONE AREA], [LOWER KEYSTONE AREA], [LEFT KEYSTONE 
AREA], or [RIGHT KEYSTONE AREA].  
						

							Chapter 4 Settings — [ADVANCED MENU] menu
ENGLISH - 97
18) Press qw to adjust the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] a\
nd [BLACK 
BORDER LEVEL].
19)
 
Press 
 as to select [BLACK BORDER LEVEL].
20)
 
Press the  button.
 fThe 

[BLACK BORDER LEVEL] screen is displayed.
 f[RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].
21)

 
Press 
 as to select an item, and press qw to adjust the setting.
 fOnce the adjustment is completed, press the  button to return to the  [BRIGHTNESS ADJUST]

 
screen.
22)
 
Press 
 as to select [UPPER], [LOWER], [LEFT], or [RIGHT] for [OVERLAPPED BLACK LEVEL].
23)
 
Press the  button.
 fThe 

[OVERLAPPED BLACK LEVEL] screen is displayed.
 f[RED], [GREEN], and [BLUE] can be adjusted individually if [INTERLOCKED] is set to [OFF].
24)

 
Press 
 as to select an item, and press qw to adjust the setting.
[BLACK BORDER WIDTH] (Right)
Projection range Edge blending [WIDTH] (Right)
[MARKER] (Red)Edge blending [START] (Right)
([MARKER] (Green))
[BLACK BORDER LEVEL] [OVERLAPPED BLACK LEVEL] (Right)
[NON-OVERLAPPED BLACK LEVEL]
Note
 f [BRIGHTNESS  ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to 
notice when [EDGE BLENDING] is used to structure a multi-display screen.  The optimal point of correction is set by adjusting [NON-
OVERLAPPED BLACK LEVEL] so the black level of the overlapping image area will be the same level as the non-overlapping area. If the 
border area of the part where the image is overlapping and the non-overlapping part gets brighter after adjusting [NON-OVERLAPPED 
BLACK LEVEL], adjust the width of the top, bottom, left, or right.  Adjust [BLACK BORDER LEVEL] when the width adjustment makes only 
the border area darker.
 f The 

joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.
 fWhen structuring a multi-display screen using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] first before 
making adjustments in Step  12)

. Adjustment method is same as the procedure of [NON-OVERLAPPED BLACK LEVEL].
 fIf only horizontal or vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0. fThe [AUT

O TESTPATTERN] setting will change in conjunction with the setting in the [DISPLAY OPTION] menu  → [COLOR MATCHING] → 
[AUTO TESTPATTERN].
 f Adjustment of the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to perform 
edge blending together with the adjustment of [GEOMETR

Y] (x   page   91). Perform the edge blending adjustment matching the shape in 
[NON-OVERLAPPED BLACK LEVEL] following Steps  17) and 18) when [NON-OVERLAPPED BLACK LEVEL] is tilted due to correcting the 
keystone with the [POSITION] menu → [GEOMETRY] → [KEYSTONE].
 f The settings for [DEF

AULT] and [USER] in the [PICTURE] menu → [GAMMA] become disabled when [EDGE BLENDING] is set to anything 
other than [OFF] while using PT
-

RW930 or PT
-
 RX110. The gamma mode will be the same as when set to [2.2].
[FRAME RESPONSE]
Set image frame delay.
1) 
Press 
 as to select [FRAME RESPONSE].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[NORMAL] Standard setting.
[FAST]
*1Simplifies the image processing to reduce image frame delay.
[FIXED]
*2Sets image frame delay to be constant regardless of the image position or magnification.
*1 [FAST] cannot be set when input signal is not interlaced signal.
*2  
Only when moving image signal or still image signal with the vertical scanning frequency of 50
   Hz or 60   Hz is input  
						

							Chapter 4 Settings — [ADVANCED MENU] menu
98 - ENGLISH
Note
 fWhen [FAST] is set, the picture quality deteriorates. The [ADVANCED MENU] menu → [DIGITAL CINEMA REALITY] cannot be set. f[FRAME RESPONSE] cannot be set while in the P
 IN P mode.
[RASTER POSITION]
This will allow the position of the image to move within the display area arbitrarily when the input image is not 
using the whole display area.
1)
 
Press 
 as to select [RASTER POSITION].
2)
 
Press the  button.
 fThe 

[RASTER POSITION]  screen is displayed.
3)
 
Press 
 asqw to adjust the position.  
						

							Chapter 4 Settings — [DISPLAY LANGUAGE] menu
ENGLISH - 99
[DISPLAY LANGUAGE] menu
On the menu screen, select [DISPLAY LANGUAGE] from the main menu, and display the sub‑menu.
Refer to “Navigating through the menu” ( x
  page   76) for the operation of the menu screen.
Changing the display language
You can select the language of the on-screen display.
1)
 
Press 
 as to select the display language and press the  button.
ENTER
DISPLAY LANGUAGE
SELECT
SET
 fVarious menus, settings, adjustment screens, control button names, etc., are displayed in the selected 
language.
 f The language can be changed to English, German, French, Spanish, Italian, Portuguese, Japanese, Chinese, 
Russian, or Korean.
Note
 f The on-screen display language is set to English in the factory default setting as well as when the [PROJECT OR SETUP] menu  → 
[INITIALIZE]  → [ALL USER DATA] is executed.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
100 - ENGLISH
[DISPLAY OPTION] menu
On the menu screen, select [DISPLAY OPTION] from the main menu, and select an item from the sub‑
menu.
Refer to “Navigating through the menu” (x

  page   76) for the operation of the menu screen.
[COLOR MATCHING]
Correct the color difference between projectors when using multiple projectors simultaneously.
Adjusting the color matching as desired
1) Press as to select [COLOR MATCHING].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Color matching adjustment is not carried out.
[3COLORS] Adjusts the three colors [RED], [GREEN], or [BLUE].
[7COLORS] Adjusts the seven colors [RED], [GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], or [WHITE].
[MEASURED] Refer to “Adjusting the color matching using a colorimeter” ( x
  page   100) for details about this mode.
3) Select [3COLORS] or [7COLORS], and press the  button.
 fThe 

[3COLORS] or [7COLORS] screen is displayed.
4)
 
Press 
 as to select [RED], [GREEN], [BLUE], or [WHITE] ([RED], [GREEN], [BLUE], [CY AN], 
[MAGENTA], [YELLOW], or [WHITE] when [7COLORS] is selected).
5)
 
Press the  button.
 fThe 

[3COLORS:RED], [3COLORS:GREEN], [3COLORS:BLUE], or [3COLORS:WHITE] screen is 
displayed.
When [7COLORS] is selected, the [7COLORS:RED], [7COLORS:GREEN], [7COLORS:BLUE], 
[7COLORS:CYAN], [7COLORS:MAGENTA], [7COLORS:YELLOW] , or [7COLORS:WHITE] screen is 
displayed.
 f By setting [AUT

O TESTPATTERN] to [ON], the test pattern for the selected color is displayed.
6)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
 fOnly [GAIN] can be adjusted when [WHITE] is selected for [3COLORS].
7)

 
Press 
 qw to adjust.
 fThe adjustment value will change between 0*1 and 2 048.
*1 The lower limit varies depending on the color to be adjusted.
Note
 f Operation when correcting the adjustment color
When the correction color same as the adjustment color is changed:  The luminance of the adjustment color changes.
When correction color red is changed: Red is added to or subtracted from the adjustment color .
When correction color green is changed: Green is added to or subtracted from the adjustment color .
When correction color blue is changed: Blue is added to or subtracted from the adjustment color .
 fSince advanced skills are necessary for the adjustment, this adjustment should be carried out by a person who is familiar with the projector 
or by a service person.
 fPressing the  button on the remote control will restore the factory default settings for all items.
 fWhen this item is set to anything other than [OFF], the [DISPLA

Y OPTION] menu → [COLOR CORRECTION] is fixed to [OFF], and the 
[PICTURE] menu → [COLOR TEMPERATURE] is fixed to [USER1].
Adjusting the color matching using a colorimeter
Use a colorimeter that can measure chromaticity coordinates and luminance to change the colors [RED], 
[GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW], or [WHITE] to desired colors.
1)
 
Press 
 as to select [COLOR MATCHING].
2)
 
Press 
 qw to select [MEASURED].