Panasonic Projector PT-RX110 User Manual

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 81
[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an item from the sub‑menu.
Refer to “Navigating through the menu” ( x
  page   76) for the operation of the menu screen.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source and the environment in which the 
projector is used.
1)
 
Press 
 as to select [PICTURE MODE].
2)
 
Press 
 qw.
 fThe 

[PICTURE MODE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[STANDARD] The image becomes suitable for moving images in general.
[CINEMA] The image becomes suitable for movie contents.
[NATURAL] The image becomes sRGB compliant.
[REC709] The image becomes Rec.709 compliant when the setting other than [PICTURE MODE] is set to the 
factory default.
[DICOM SIM.] The image becomes similar to that of DICOM Part 14 Grayscale Standard.
[DYNAMIC] The light output is maximized for use in bright areas.
[GRAPHIC] The image becomes suitable for input from the personal computer.
Note
 fThe factory default picture mode is [GRAPHIC] for still image input signals and [ST ANDARD] for movie-based input signals. fRec.709 is an abbreviation of “ITU-R Recommendation BT
.709” and is a color standard of high-vision broadcasting.
 fDICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices.  Although the 
DICOM name is used, the projector is not a medical device, and display images should not be used for medical purposes such as diagnosis.
 f While the item in [PICTURE MODE] is selected, press the  button to save as the default value for when a new signal is input.  The 
data of all items except [SYSTEM SELECT

OR] in the [PICTURE] menu is saved.
[CONTRAST]
You can adjust the contrast of the colors.
1) 
Press 
 as to select [CONTRAST].
2)
 
Press 
 qw or the  button.
 fThe 

[CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. The screen becomes brighter.
-31 - +31
Press q. The screen becomes darker.
Attention
 f
Adjust the [PICTURE] menu  → [BRIGHTNESS] first when you need to adjust the black level.
[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1)
 
Press 
 as to select [BRIGHTNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[BRIGHTNESS] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.  
						

							Chapter 4 Settings — [PICTURE] menu
82 - ENGLISH
OperationAdjustmentRange of adjustment
Press w. Increases the brightness of the dark (black) parts of the screen.
-31 - +31
Press q. Reduces the brightness of the dark (black) parts of the screen.
[COLOR]
You can adjust the color saturation of the projected image.
1)
 
Press 
 as to select [COLOR].
2)
 
Press 
 qw or the  button.
 fThe 

[COLOR] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Deepens colors.
-31 - +31
Press q. Weakens colors.
[TINT]
You can adjust the skin tone in the projected image.
1)
 
Press 
 as to select [TINT].
2)
 
Press 
 qw or the  button.
 fThe 

[TINT] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Adjusts skin tone toward greenish color.
-31 - +31
Press q. Adjusts skin tone toward reddish purple.
[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
Adjusting with color temperature
1) Press 
as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[USER1] Adjusts white balance as desired. Refer to “Adjusting desired white balance” ( x
  page   82) for 
details.
[USER2]
[3200K] - [9300K] Sets the value in increments of 100
  K.
Select an item so that images become natural.
Note
 f [DEFAULT] cannot be selected when the [PICTURE] menu → [PICTURE MODE] is set to [DICOM SIM.]. fThis item is fixed to [USER1] when the [DISPLA
Y OPTION] menu → [COLOR MATCHING] is set to anything other than [OFF].
 fThe color temperature numerical values are guidelines.
Adjusting desired white balance
1) Press  as to select [COLOR TEMPERATURE].  
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 83
2) Press qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER1] or [USER2].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.
5)
 
Press 
 as to select [WHITE BALANCE].
6)
 
Press the  button.
 fThe 

[WHITE BALANCE] screen is displayed.
7)
 
Press 
 as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].
8)
 
Press the  button.
 fThe 

[WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.
9)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
10)
 
Press 
 qw to adjust the level.
Item Operation Adjustment Range of adjustment
[RED] Press w.
Deepens red.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is +255)
[WHITE BALANCE LOW]: 
-127 - +127 (factory default is 
0)
Press q.
Weakens red.
[GREEN] Press w.
Deepens green.
Press q. Weakens green.
[BLUE] Press w.
Deepens blue.
Press q. Weakens blue.
Note
 f
Adjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
Adjusting to desired white balance based on existing color temperature s\
ettings
1) Press  as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select anything other than [DEFAULT], [USER1], or [USER2].
4)
 
Press the  button.
 fThe 

[CHANGE TO *****] screen is displayed.
5)
 
Press 
 as to select [USER1] or [USER2].
 fThe status of the color temperature changed is saved to the selected item.
6)

 
Press the  button.
 fThe confirmation screen is displayed.
7)

 
Press 
 qw to select [OK], and press the  button.
 fThe [USER1] or [USER2] data is overwritten.
 fThe data is not overwritten when [CANCEL] is selected with  qw

 and the  button is pressed.
 fThe 

[WHITE BALANCE HIGH] screen is displayed.
8)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
9)
 
Press 
 qw to adjust the level.  
						

							Chapter 4 Settings — [PICTURE] menu
84 - ENGLISH
Note
 fAdjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
 f When color temperature has been changed, the colors before and after the change will dif fer slightly

.
Changing the name of [USER1] or [USER2]
1) Press as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER1] or [USER2].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.
5)
 
Press 
 as to select [COLOR TEMPERATURE NAME CHANGE].
6)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE NAME CHANGE] screen is displayed.
7)
 
Press 
 asqw to select the text, and press the  button to enter the text.
8)
 
Press 
 asqw to select [OK], and press the  button.
 fThe name set to color temperature is changed.
Note
 f The display of [USER1] or [USER2] is also changed when the name is changed.
[WHITE GAIN]
Adjust the brightness of the white part of the image.
1)
 
Press 
 as to select [WHITE GAIN].
2)
 
Press 
 qw or the  button.
 fThe 

[WHITE GAIN]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Brightness of the white part gets stronger.
0 - +10
Press q. The image becomes more natural.
[GAMMA]
You can switch gamma mode.
1)
 
Press 
 as to select [GAMMA].
2)
 
Press 
 qw or the  button.
 fThe 

[GAMMA] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[USER] Uses the gamma data registered by the user.
(Registration requires separate software. Consult your dealer.)
[1.8] Set so that images become as you like.
[2.0]
[2.2]  
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 85
Note
 fWhen the edge blending adjustment is performed while [DEF AULT] is selected, it will be the same gamma mode as when [2.2] is selected.
(Only for PT- RW930, PT- RX110)
Changing the [USER] name
1) Press as to select [GAMMA].
2)  
Press 
 qw or the  button.
 fThe 

[GAMMA] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER].
4)
 
Press the  button.
 fThe 

[GAMMA] screen is displayed.
5)
 
Press the  button.
 fThe 

[GAMMA NAME CHANGE]  screen is displayed.
6)
 
Press 
 asqw to select the text, and press the  button to enter the text.
7)
 
Press 
 asqw to select [OK], and press the  button.
 fThe gamma selection name is changed.
Note
 f Display of [USER] is also changed when the name is changed.
[SYSTEM DAYLIGHT VIEW]
You can correct the image to the optimal vividness even if it is projected under a bright light.
1)
 
Press 
 as to select [SYSTEM DAYLIGHT VIEW].
2)
 
Press 
 qw or the  button.
 fThe 

[SYSTEM DAYLIGHT VIEW]  individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] - [6] Corrects the vividness of the image. The larger the value, the stronger the correction.
[SHARPNESS]
You can adjust the sharpness of the projected image.
1)
 
Press 
 as to select [SHARPNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[SHARPNESS]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Contours become sharper.
0 - +15
Press q. Contours become softer.
Note
 f
If you press  w while the adjustment value is [+15], the value will become [0]. If you press  q while the adjustment value is [0], the value will 
become [+15].  
						

							Chapter 4 Settings — [PICTURE] menu
86 - ENGLISH
[NOISE REDUCTION]
You can reduce noises when the input image is degraded and noise is occurring in the image signal.
1) 
Press 
 as to select [NOISE REDUCTION].
2)
 
Press 
 qw or the  button.
 fThe 

[NOISE REDUCTION] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Slightly corrects the noise.
[2] Moderately corrects the noise.
[3] Strongly corrects the noise.
Attention
 fWhen this is set for an input signal with less noise, the image may look dif ferent from the original image. In such a case, set it to [OFF].
[DYNAMIC CONTRAST]
Light adjustment of the light source and signal compensation are performed automatically according to the image 
to make the contrast optimum for the image.
1)
 
Press 
 as to select [DYNAMIC CONTRAST].
2)
 
Press 
 qw or the  button.
 fThe 

[DYNAMIC CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the dynamic contrast function.
[1] Adjusts the light source and compensates signals to a small extent.
[2] Adjusts the light source and compensates signals to a moderate extent.
[3] Adjusts the light source and compensates signals to a large extent.
[USER] Set any desired correction.
Refer to “Performing desired correction” (
x
  page   86) for details.
Performing desired correction
1) Press as to select [DYNAMIC CONTRAST].
2)  
Press 
 qw or the  button.
 fThe 

[DYNAMIC CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER].
4)
 
Press the  button.
 fThe 

[DYNAMIC CONTRAST] screen is displayed.
5)
 
Press 
 as to select the item to set.
 fThe items in the detailed setting will switch each time you press  qw

.
 fPress the  button when [MUL

TI PROJECTOR SYNC] is selected.
Setting item Details
[AUTO CONTRAST]
(Automatic light source  adjustment) [OFF]
Does not adjust the light source.
[1] - [255] The higher the value, the stronger the light adjustment of the light 
source.
Can be set in increments of 1.  
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 87
Setting itemDetails
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness 
level of the signal to start the  light adjustment) [6%] - [50%]Adjusts the light source when the brightness level of the video 
signal being input gets lower than the set value. The higher the 
value, the larger the range to perform the light adjustment of the 
light source.
Can be set in increments of 1
  %. (Factory setting: 30   %)
[LIGHTS OUT TIMER]
(Time setting until the light  turns off) [DISABLE]
Does not turn off the light source.
[0.0s] - [10.0s] Turns off the light source when the brightness level of the video 
signal being input goes under the value set in [LIGHTS OUT 
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s].
[0.0s] - [4.0s] can be selected in increments of 0.5.
[LIGHTS OUT SIGNAL  LEVEL]
(Setting of the brightness 
level of the signal to turn off  the light) [0%] - [5%]
Sets the level of the brightness of the video signal to turn off the 
light source with [LIGHTS OUT TIMER].
Can be set in increments of 1
  %. (Factory setting: 0   %)
[MANUAL INTENSITY] (Manual light source  adjustment) [0] - [255]
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
[DYNAMIC GAMMA]
(Adjustment of signal  compensation) [OFF]
Does not compensate the signal.
[1] Slightly compensates the signal.
[2] Moderately compensates the signal.
[3] Strongly compensates the signal.
[MULTI PROJECTOR SYNC] Sets the contrast synchronization function.
This setting item is common with the following menu item.
 f
The [PROJECT

OR SETUP] menu → [MULTI PROJECTOR 
SYNC]
Refer to the [PROJECTOR SETUP] menu → [MULTI PROJECTOR 
SYNC] (x
  page   134) for details.
Note
 f[LIGHTS OUT  SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE]. fWhen [LIGHTS OUT
 TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again 
from the state that the light source has turned off by this function.
 g When the brightness level of the video signal being input has exceeded the value set in [LIGHTS OUT  SIGNAL

 LEVEL]
 gWhen the input signal is gone gWhen on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed gWhen the operating environment temperature is around 0

  °C (32   °F) and the light source is forced to turn on due to warm-up
 fWhen the image of analog signal is projected, the image may be af fected by the signal noise while the brightness level of the video signal 
is detected. In such case, it is determined that the signal has not fallen below even when the brightness level of the image falls below the 
value set in [LIGHTS OUT

 SIGNAL LEVEL].
 fThe contrast will be maximized when [DYNAMIC GAMMA] is set to [3]. fThe brightness control function and the dynamic contrast function will operate simultaneously , but the dynamic contrast function will not 
operate while measuring the brightness and the color

.
 fThe contrast synchronization function is a function to display a combined screen with a balanced contrast by sharing the brightness level of 
the video signal input to each projector when a multi-display is constructed by combining the projected image of multiple projectors.
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, but you can set the system method manually when an 
unstable signal is input. Set the system method matching the input signal.
1)
 
Press 
 as to select [SYSTEM SELECTOR].
2)
 
Press the  button.
3)

 
Press 
 as to select a system format.
 fSelect the system format with 

asqw when a signal is input connected to the  terminal. (Only for 
PT
-

RZ970)
 fA

vailable system formats vary depending on the input signal.
Terminal System format
 terminal, / terminal Select [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL - M], [PAL - N], [SECAM], or [PAL60].
Select [AUTO] normally. ([AUTO] will automatically determine from [NTSC], [NTSC4.43], [PAL], 
[PAL - M], [PAL - N], [SECAM], or [PAL60].)
Switch the setting to the appropriate TV signal format.  
						

							Chapter 4 Settings — [PICTURE] menu
88 - ENGLISH
TerminalSystem format
 terminal,  terminal 480/60i, 576/50i, or 576/50p 
signal Select [RGB] or [YC
BCR].
640
 
x
 
480/60 or 480/60p  signal Select an item from [640x480/60], [480/60p YC
BCR], or [480/60p 
RGB].
Other moving image signals Select [RGB] or [YP
BPR].
 terminal 480/60i, 576/50i, 480/60p, or 
576/50p signal Select [RGB] or [YC
BCR].
Other moving image signals Select [RGB] or [YP
BPR].
 terminal,  terminal 480/60i, 576/50i, 480/60p, or 
576/50p signal Select [AUTO], [RGB], or [YC
BCR].
Other moving image signals Select [AUTO], [RGB], or [YP
BPR].
 terminal
(Only for PT
-

RZ970) Select an item from [AUTO], [480/60i YC
BCR], [576/50i YCBCR], [720/50p YPBPR], [720/60p YPBPR], 
[1080/24p
 YPBPR], [1080/24sF YPBPR], [1080/25p YPBPR], [1080/30p YPBPR], [1080/50i YPBPR], 
[1080/60i
 YPBPR], [1080/50p YPBPR], [1080/60p YPBPR], [1080/24p RGB], [1080/24sF RGB], 
[1080/25p
 
RGB], [1080/30p
 
RGB], [1080/50i
 
RGB], [1080/60i   RGB], [2K/24p   RGB], [2K/25p RGB], 
[2K/30p RGB], [2K/48p
 
YPBPR], [2K/50p YPBPR], or [2K/60p YPBPR].
4) Press the  button.
Note
 f For details of the types of video signals that can be used with the projector , refer to “List of compatible signals” (x   page   200). fThis may not function properly for some connected external devices.
sRGB-compliant video
sRGB is an international standard (IEC61966-2-1) for color reproduction defined by IEC (International 
Electrotechnical Commission).
Set according to the following steps to reproduce more faithful, sRGB compliant colors.
1)
 
Set [COLOR MA
 TCHING] to [OFF].
 fRefer to [COLOR MA

TCHING] (x   page   100).
2)
 
Display the [PICTURE] menu.
 fRefer to “[PICTURE] menu” (

x   page   81).
3)
 
Press 
 as to select [PICTURE MODE].
4)
 
Press 
 qw to set [NATURAL].
5)
 
Press 
 as to select [COLOR].
6)
 
Press the  button on the remote control to set the factory default setting.
7)
 
Follow Steps 5) 
 ‑  6) to set [TINT], [COLOR TEMPERATURE], [WHITE GAIN], [GAMMA], and [SYSTEM 
DAYLIGHT VIEW] to the factory default settings.
Note
 f sRGB is available for RGB signal input only .  
						

							Chapter 4 Settings — [POSITION] menu
ENGLISH - 89
[POSITION] menu
On the menu screen, select [POSITION] from the main menu, and select an item from the sub‑menu.
Refer to “Navigating through the menu” ( x
  page   76) for the operation of the menu screen.
Note
 f When the optional DIGIT AL LINK output supported device (Model No.: ET- YFB100G, ET- YFB200G) is connected to the  terminal, adjust the shift, aspect, and clock phase from the menu of DIGIT AL LINK output supported device at first.
[SHIFT]
Move the image position vertically or horizontally if the image projected on the screen is still out of position even 
when the positions of the projector and screen are correct.
1)
 
Press 
 as to select [SHIFT].
2)
 
Press the  button.
 fThe 

[SHIFT] screen is displayed.
3)
 
Press 
 asqw to adjust the position.
Orientation Operation Adjustment
Vertical (up and down)  adjustment Press a.
The image position moves up.
Press s. The image position moves down.
Horizontal (right and left) 
adjustment Press w.
The image position moves to the right.
Press q.The image position moves to the left.
Note
 f
For the portrait setting, image position is moved horizontally when “V ertical (up and down) adjustment” is made. Image position is moved 
vertically when “Horizontal (right and left) adjustment” is made.
[ASPECT]
You can switch the aspect ratio of the image.
The aspect ratio is switched within the screen range selected in the [DISPLA Y OPTION] menu → [SCREEN 
SETTING]  → [SCREEN FORMAT]. Set [SCREEN FORMAT] first. ( x
  page   101)
1)
 
Press 
 as to select [ASPECT].
2)
 
Press 
 qw or the  button.
 fThe 

[ASPECT] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Displays images without changing the aspect ratio of the input signals.
[VID AUTO]
*1Identifies the video ID (VID) embedded in the video signal, and automatically switches the image size 
between 4:3 and 16:9. This is enabled when NTSC signal is input.  
						

							Chapter 4 Settings — [POSITION] menu
90 - ENGLISH
[AUTO]*2The projector identifies the video ID (VID) embedded in the video signals and displays the image by 
automatically switching the screen sizes between 4:3 and 16:9. This function is effective for 480/60i 
and 480/60p signals.
[THROUGH] Displays images without changing the resolution of the input signals.
[16:9] Displays images with the aspect ratio converted to 16:9 when standard signals are input
*3. When 
wide-screen signals are input*4, the images are displayed without changing the aspect ratio.
[4:3] Displays images without changing the aspect ratio when standard signals are input
*3. When wide-
screen signals are input*4, the images are reduced to be displayed without changing input aspect ratio 
so that the images will fit in the 4:3 screen.
[H FIT] Displays images using the entire width of the screen range selected in [SCREEN FORMA
T]. When 
signals have the aspect ratio vertically longer than the screen aspect ratio selected in [SCREEN 
FORMAT], the images are displayed with the top and bottom parts cut off.
[V FIT] Displays images using the entire height of the screen range selected in [SCREEN FORMA
T]. When 
signals have the aspect ratio horizontally longer than the aspect ratio of the screen selected in 
[SCREEN FORMAT], the images are displayed with the right and left parts cut off.
[HV FIT] Displays images in the entire screen range selected in [SCREEN FORMA
T]. When the aspect ratio of 
the input signals differs from that of the screen range, the images are displayed with the aspect ratio 
converted to that of the screen selected in [SCREEN FORMAT].
*1 During video signals and  Y/C signal (NTSC) input only
*2  
During RGB signal (480/60i, 480/60p) input only
*3

 
Standard signals are input signals with an aspect ratio of 4:3 or 5:4.
*4

 
Wide-screen signals are input signals with an aspect ratio of 16:10, 16:9, 15:9 or 15:10.
Note
 f Some size modes are not available for certain types of input signals. [DEF AUL T] cannot be selected for video signal, Y/C signal (NTSC), or 
analog RGB signal (480/60i, 480/60p).
 f If an aspect ratio which is dif

ferent from the aspect ratio for the input signals is selected, the images will appear dif ferently from the originals. 
Be careful of this when selecting the aspect ratio.
 f If using the projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that 
adjusting the aspect ratio or using the zoom function to change the screen images may be an infringement of the rights of the original 
copyright owner for that program under copyright protection laws.  T

ake care when using a function of the projector such as the aspect ratio 
adjustment and zoom function.
 f If conventional (normal) 4:3 images which are not wide-screen images are displayed on a wide screen, the edges of the images may not 
be visible or they may become distorted. Such images should be viewed as with an aspect ratio of 4:3 in the original format intended by the 
creator of the images.
[ZOOM]
You can adjust the image size.
The adjustments in [ZOOM] will differ depending on the setting of the [POSITION] menu → [ASPECT].
When [ASPECT] is set to other than [DEFAULT] and [THROUGH]
1) Press  as to select [ZOOM].
2)  
Press the  button.
 fThe 

[ZOOM] screen is displayed.
3)
 
Press 
 as to select [INTERLOCKED].
4)
 
Press 
 qw to switch the item.
[OFF] Sets the [VERTICAL] and [HORIZONTAL] zoom ratio.
[ON] Uses [BOTH] to set zoom ratio. Image can be enlarged or reduced vertically and horizontally at the 
same magnification.
5) Press 
as to select [VERTICAL] or [HORIZONTAL].
 fIf [ON] is selected, select [BOTH].
6)

 
Press 
 qw to adjust.
Note
 f When the [POSITION] menu  →  [ASPECT] is set to [THROUGH], [ZOOM] cannot be adjusted.