Panasonic Projector PT-RX110 User Manual

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 101
3) Press the  button.
 fThe 

[MEASURED MODE] screen is displayed.
4)
 
Press 
 as to select [MEASURED DATA].
5)
 
Press the  button.
 fThe 

[MEASURED DATA] screen is displayed.
6)
 
Measure the current luminance (Y) and the chromaticity coordinates (x, y) using the colorimeter .
7)

 
Press 
 as to select a color, and press qw to adjust the setting.
 fSet [AUT

O TESTPATTERN] to [ON] to display a test pattern of selected colors.
8)
 
Once all the input is completed, press the  button.
 fThe 

[MEASURED MODE] screen is displayed.
9)
 
Press 
 as to select [TARGET DATA].
10)
 
Press the  button.
 fThe 

[TARGET DATA] screen is displayed.
11)
 
Press 
 as to select a color and press qw to input coordinates for desired colors.
 fBy setting [AUT

O TESTPATTERN] to [ON], the test pattern for the selected color is displayed.
12)
 
Once all the input is completed, press the  button.
Note
 f Colors are not displayed properly when target data is a color outside the region of this projector . fSet the [AUT
O TESTPATTERN] to [ON] to automatically display a test pattern for use in adjusting the selected adjustment colors.
 fThe [AUT

O TESTPATTERN] setting will change in conjunction with the setting in the [ADVANCED MENU] menu → [EDGE BLENDING]  → 
[ON]/[USER]  → [AUTO TESTPATTERN].
 fWhen using a colorimeter or similar instrument to take measurement, measure the colors displayed in [AUT O 

TESTPATTERN].
 fA

 difference in the color coordinates of target data and measurement value obtained from an instrument may occur for certain instrument 
and measurement environment used.
[COLOR CORRECTION]
Colors can be adjusted and registered for each input signal format.
1)
 
Press 
 as to select [COLOR CORRECTION].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Standard setting.
[USER] For each of the four signal formats of VIDEO, Y/C, RGB, and YC
BCR/YPBPR, six colors of red, green, 
blue, cyan, magenta, and yellow can be adjusted and registered. Press the  button and set 
the details. Adjustment is possible within the range of 
-31 to +31.
[SCREEN SETTING]
Set the screen size.
Correct to the optimum image position for the set screen when the aspect ratio of a projected image is changed. 
Set as necessary for the screen in use.
1)
 
Press 
 as to select [SCREEN SETTING].
2)
 
Press the  button.
 fThe 

[SCREEN SETTING] screen is displayed.
3)
 
Press 
 qw to switch the [SCREEN FORMAT] item.
 fThe items will switch each time you press the button.
Model No. [SCREEN FORMAT] Range when [SCREEN POSITION] is selected
PT
-
 RZ970 [16:10]
Cannot be adjusted.
[4:3] Adjusts the horizontal position between 
-160 and 160.
[16:9] Adjusts the vertical position between 
-60 and 60.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
102 - ENGLISH
Model No.[SCREEN FORMAT] Range when [SCREEN POSITION] is selected
PT
-
 RW930 [16:10]
Cannot be adjusted.
[16:9] Adjusts the vertical position between 
-40 and 40.
PT
-

RX110 [4:3]
Cannot be adjusted.
[16:9] Adjusts the vertical position between 
-96 and 96.
4) Press as to select [SCREEN POSITION].
 f[SCREEN POSITION] cannot be selected or adjusted when [SCREEN FORMA T] is set to the following 
item.
 g PT-

RZ970, PT
-
 RW930: [16:10]
 gPT-

RX110: [4:3]
5)
 
Press 
 qw to adjust [SCREEN POSITION].
[AUTO SIGNAL]
Set whether to execute automatic setup of signals automatically.
The screen display position or signal level can be adjusted automatically without pressing the  
button on the remote control on each occasion if you input unregistered signals frequently at meetings, etc.
1)
 
Press 
 as to select [AUTO SIGNAL].
2)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Sets the auto signal function to off.
[ON] Executes automatic setup automatically when images are changed to unregistered signals during 
projection.
[AUTO SETUP]
Set this when adjusting a special signal or horizontally long (such as 16:9) signal.
Setting with [MODE]
1) Press 
as to select [AUTO SETUP].
2)  
Press the  button.
 fThe 

[AUTO SETUP] screen is displayed.
3)
 
Press 
 as to select [MODE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[WIDE] Select this item when an image aspect ratio is a wide-screen signal, which does not meet the 
[DEFAULT] setting.
[USER] Select this when receiving a signal with a special horizontal resolution (number of display dots).
 fProceed to Step  7) when [DEFAULT] or [WIDE] is selected.
 fProceed to Step 

5) when [USER] is selected.
5)
 
Press 
 as to select [DISPLAY DOTS], and press qw to match [DISPLAY DOTS] to the horizontal 
resolution of the signal source.
6)
 
Press 
 as to select [MODE].
7)
 
Press the  button.
 f Automatic adjustment is executed. [PROGRESS] is displayed while in automatic adjustment. When 
completed, the screen returns to the  [AUT

O SETUP] screen.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 103
Note
 fAutomatic setup of signal can be executed when analog RGB signal consisting of dots such as computer signal, or DVI - D/HDMI signal is 
being input.
Adjusting position automatically
1) Press  as to select [AUTO SETUP].
2)  
Press the  button.
 fThe 

[AUTO SETUP] screen is displayed.
3)
 
Press 
 as to select [POSITION ADJUST].
4)
 
Press 
 qw to switch the item.
[ON] Adjust the screen position and size when automatic setup is executed.
[OFF] Does not perform automatic adjustment.
Adjusting signal level automatically
1) Press as to select [AUTO SETUP].
2)  
Press the  button.
 fThe 

[AUTO SETUP] screen is displayed.
3)
 
Press 
 as to select [SIGNAL LEVEL ADJUST].
4)
 
Press 
 qw to switch the item.
[OFF] Does not perform automatic adjustment.
[ON] Adjusts black level (the [PICTURE] menu 
→ [BRIGHTNESS]) and white level (the [PICTURE] menu 
→ [CONTRAST]) when automatic setup is executed.
Note
 f [SIGNAL LEVEL ADJUST] may not function properly unless a still image containing clear blacks and whites is input.
[BACKUP INPUT SETTING]
Set the backup function that switches the signal to the backup input signal as seamless as possible when input 
signal is disrupted.
1)
 
Press 
 as to select [BACKUP INPUT SETTING].
2)
 
Press the  button.
 fThe 

[BACKUP INPUT SETTING]  screen is displayed.
3)
 
Press 
 as to select [BACKUP INPUT MODE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the backup function.
[ON] Enables the backup function between the DVI
- D input and the HDMI input. The input is switched as 
seamless as possible when the same signal is input to the primary and secondary inputs.
Primary input is fixed to the  terminal, and the secondary input is fixed to the  
terminal.
5) Press  as to select [AUTOMATIC SWITCHING].
 f[AUT

OMATIC SWITCHING] cannot be selected when [BACKUP INPUT MODE] is set to [OFF].
6)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[ENABLE] Switches to the secondary input automatically when the input signal for primary input is disrupted.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
104 - ENGLISH
[DISABLE]Disables the automatic input switching function.
Note
 fBackup function is enabled only when the [BACKUP  INPUT MODE] is set to [ON], and the same signal is input to the  and 
 terminals.
 f T

o switch to the backup input signal using the backup function, make sure that the following three conditions are satisfied to be ready to use 
the function.
 g Set [BACKUP

 INPUT MODE] to [ON].
 gInput the same signal to the primary and secondary inputs. gDisplay the image of the primary input. fIf the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to use 
the backup function is canceled. 

To switch to the backup input signal using the backup function again, switch to the primary input.
 f[BACKUP

 INPUT STATUS] is displayed in the input guide ( x
  page   110) and [STATUS] screen (x pages 74, 138) when [BACKUP 
INPUT MODE] is set to [ON].
When switching to the backup input signal is possible using the backup function, [ACTIVE] is displayed in [BACKUP  INPUT STATUS]. When 
it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the primary 
input is displayed.
The primary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the secondary 
input is displayed.
 f The input is switched seamlessly when the DVI

- D and HDMI inputs are switched while [BACKUP INPUT MODE] is set to [ON] and switching 
to the backup input signal is possible.
 f When [AUT

OMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] is [ACTIVE], the signal is switched to the backup 
input if a disruption occurs in the input signal.
 f When [AUT

OMATIC SWITCHING] is set to [ENABLE] and the signal is automatically switched to the backup input due to disruption of the 
input signal, [BACKUP INPUT STATUS] changes to [INACTIVE]. In this case, switching to the backup input signal is not possible until the 
original input signal is restored. If the signal is automatically switched to the backup input, switching to the backup input signal becomes 
possible when the original input signal is restored. In this case, the current input is retained.
 f [BACKUP

 INPUT SETTING] cannot be set during P IN P. The backup operation is not performed either.
[RGB IN]
Set the  terminal and the  terminal.
Setting [RGB1 INPUT SETTING]
1) Press  as to select [RGB IN].
2)  
Press the  button.
 fThe 

[RGB IN] screen is displayed.
3)
 
Press 
 as to select [RGB1 INPUT SETTING].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[RGB/YPBPR] Select this item when an RGB signal or YCBCR/YPBPR signal is input to the  terminal.
[VIDEO] Select this item when a video signal is input to the  terminal ().
[Y/C] Select this item when a luminance signal and color signal are input to the  terminal (, ).
Switching the slice level of an input synchronization signal
1) Press 
as to select [RGB IN].
2)  
Press the  button.
 fThe 

[RGB IN] screen is displayed.
3)
 
Press 
 as to select [RGB1 SYNC SLICE LEVEL] or [RGB2 SYNC SLICE LEVEL].
4)
 
Press 
 qw to switch the item.
[LOW] Set the slice level to [LOW].
[HIGH] Set the slice level to [HIGH].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 105
Setting [RGB2 EDID MODE]
1) Press as to select [RGB IN].
2)  
Press the  button.
 fThe 

[RGB IN] screen is displayed.
3)
 
Press 
 as to select [RGB2 EDID MODE].
4)
 
Press the  button.
 fThe 

[RGB2 EDID MODE] screen is displayed.
5)
 
Press 
 qw to switch [EDID MODE].
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[SCREEN FIT] Changes the EDID data according to the [SCREEN FORMAT] setting.
[USER] Sets the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fProceed to Step  10) when [DEFAULT] or [SCREEN FIT] is selected.
6)
 
Press the  button.
 f The 

[RESOLUTION] screen is displayed.
7)
 
Press 
 asqw  to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], or [1920x1200p].
8)

 
Press the  button.
 f The 

[VERTICAL SCAN FREQUENCY] screen is displayed.
9)
 
Press 
 qw to select [VERTICAL SCAN FREQUENCY].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for [RESOLUTION].
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[1920x1080p], [1920x1080i]
10)

 
Press the  button.
 f The confirmation screen is displayed.
1

1)
 
Press 
 qw to select [OK], and press the  button.
Note
 f Settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in the  [RGB IN] screen. fSetting of the resolution and the vertical scanning frequency may be necessary on the computer or video device in use. fThe computer

, video device, or projector in use may require the power to be turned of f and on again after setting.
 fThe output with the set resolution or vertical scanning frequency may not be possible depending on the computer or video device in use.
[DVI-D IN]
Set this item in accordance with the video signal input to the  terminal.
Setting [SIGNAL LEVEL] in [DVI-D IN]
1) Press  as to select [DVI-D IN].
2)  
Press the  button.
 fThe 

[DVI-D IN] screen is displayed.
3)
 
Press 
 as to select [SIGNAL LEVEL].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
106 - ENGLISH
[0-255:PC]Select this item when the signal output from the DVI - D terminal of the external device (such as a 
computer) is input to the  terminal.
[16-235] Select this item when the signal output from the HDMI terminal of the external device (such as a Blu-
ray disc player) is input to the  terminal using a conversion cable, etc.
Note
 f
The optimal setting varies depending on the output setting of the connected external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
Setting [EDID SELECT] in [DVI-D IN]
1) Press  as to select [DVI-D IN].
2)  
Press the  button.
 fThe 

[DVI-D IN] screen is displayed.
3)
 
Press 
 as to select [EDID SELECT].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[EDID3] Determines the moving image or still image signal automatically.
[EDID1] Select this item mainly when an external device that will output the moving image signal (such as a 
Blu-ray disc player) is connected to the  terminal.
[EDID2:PC] Select this item mainly when an external device that will output the still image signal (such as a 
computer) is connected to the  terminal.
Note
 f
The data for plug and play will change when the setting is changed. Refer to “List of compatible signals” ( x   page   200) for details on a 
resolution that supports plug and play.
Setting [EDID MODE] in [DVI-D IN]
1) Press  as to select [DVI-D IN].
2)  
Press the  button.
 fThe 

[DVI-D IN] screen is displayed.
3)
 
Press 
 as to select [EDID MODE].
4)
 
Press the  button.
 fThe 

[DVI-D EDID MODE] screen is displayed.
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[SCREEN FIT] Changes the EDID data according to the [SCREEN FORMAT] setting.
[USER] Sets the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fProceed to Step  10) when [DEFAULT] or [SCREEN FIT] is selected.
6)
 
Press the  button.
 f The 

[RESOLUTION] screen is displayed.
7)
 
Press 
 asqw  to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], or [1920x1200p].
8)

 
Press the  button.
 f The 

[VERTICAL SCAN FREQUENCY] screen is displayed.
9)
 
Press 
 qw to select [VERTICAL SCAN FREQUENCY].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for [RESOLUTION].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 107
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[1920x1080p], [1920x1080i]
10)

 
Press the  button.
 f The confirmation screen is displayed.
1

1)
 
Press 
 qw to select [OK], and press the  button.
Note
 f Settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in the  [DVI-D IN] screen. fSetting of the resolution and the vertical scanning frequency may be necessary on the computer or video device in use. fThe computer

, video device, or projector in use may require the power to be turned of f and on again after setting.
 fThe output with the set resolution or vertical scanning frequency may not be possible depending on the computer or video device in use.
[HDMI IN]
Set this item in accordance with the video signal input to the  terminal.
Setting [SIGNAL LEVEL] in [HDMI IN]
1) Press  as to select [HDMI IN].
2)  
Press the  button.
 fThe 

[HDMI IN] screen is displayed.
3)
 
Press 
 as to select [SIGNAL LEVEL].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[64-940] Select this item when the signal output from the HDMI terminal of an external device (such as a Blu-
ray disc player) is input to the  terminal.
[0-1023] Select this item when the signal output from the DVI
- D terminal of an external device (such as a 
computer) is input to the  terminal via a conversion cable or similar cable.
Select this item also when the signal output from the HDMI terminal of a computer or other device is 
input to the  terminal.
Note
 f The optimal setting varies depending on the output setting of the connected external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
 fThe HDMI signal level is displayed for 30

  bits of input.
Setting [EDID MODE] in [HDMI IN]
1) Press as to select [HDMI IN].
2)  
Press the  button.
 fThe 

[HDMI IN] screen is displayed.
3)
 
Press 
 as to select [EDID MODE].
4)
 
Press the  button.
 fThe 

[HDMI EDID MODE] screen is displayed.
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[SCREEN FIT] Changes the EDID data according to the [SCREEN FORMAT] setting.
[USER] Set the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fProceed to Step  10) when [DEFAULT] or [SCREEN FIT] is selected.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
108 - ENGLISH
6) Press the  button.
 fThe 

[RESOLUTION] screen is displayed.
7)
 
Press 
 asqw to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], or [1920x1200p].
8)

 
Press the  button.
 fThe 

[VERTICAL SCAN FREQUENCY] screen is displayed.
9)
 
Press 
 qw to select [VERTICAL SCAN FREQUENCY].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for [RESOLUTION].
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[1920x1080p], [1920x1080i]
10)

 
Press the  button.
 fThe confirmation screen is displayed.
1

1)  
Press 
 qw to select [OK], and press the  button.
Note
 f Settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in the  [HDMI IN] screen. fSetting of the resolution and the vertical scanning frequency may be necessary on the computer or video device in use.
 fThe computer

, video device, or projector in use may require the power to be turned of f and on again after setting.
 fThe output with the set resolution or vertical scanning frequency may not be possible depending on the computer or video device in use.
[DIGITAL LINK IN]
Set this item in accordance with the video signal input to the  terminal.
Setting [SIGNAL LEVEL] in [DIGITAL LINK IN]
1) Press as to select [DIGITAL LINK IN].
2)  
Press the  button.
 fThe 

[DIGITAL LINK IN] screen is displayed.
3)
 
Press 
 as to select [SIGNAL LEVEL].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[64-940] Select this item when the signal output from the HDMI terminal of an external device (Blu-ray disc 
player, etc.) is input to the  terminal via a twisted-pair-cable transmitter.
[0-1023] Select this item when the signal output from the DVI
- D terminal or HDMI terminal of an external 
device (such as a computer) is input to the  terminal via a twisted-pair-cable 
transmitter.
Note
 f The optimal setting varies depending on the output setting of the connected external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
 fThe signal level is displayed for 30 bits of input.
Setting [EDID MODE] in [DIGITAL LINK IN]
1) Press  as to select [DIGITAL LINK IN].
2)  
Press the  button.
 fThe 

[DIGITAL LINK IN] screen is displayed.
3)
 
Press 
 as to select [EDID MODE].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 109
4) Press the  button.
 fThe 

[DIGITAL LINK EDID MODE] screen is displayed.
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[SCREEN FIT] Changes the EDID data according to the [SCREEN FORMAT] setting.
[USER] Sets the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fProceed to Step  10) when [DEFAULT] or [SCREEN FIT] is selected.
6)
 
Press the  button.
 f The 

[RESOLUTION] screen is displayed.
7)
 
Press 
 asqw  to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], or [1920x1200p].
8)

 
Press the  button.
 f The 

[VERTICAL SCAN FREQUENCY] screen is displayed.
9)
 
Press 
 qw to switch [VERTICAL SCAN FREQUENCY].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for [RESOLUTION].
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[1920x1080p], [1920x1080i]
10)

 
Press the  button.
 f The confirmation screen is displayed.
1

1)
 
Press 
 qw to select [OK], and press the  button.
Note
 f Settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in the  [DIGITAL LINK IN] screen. fSetting of the resolution and the vertical scanning frequency may be necessary on the computer or video device in use. fThe computer

, video device, or projector in use may require the power to be turned of f and on again after setting.
 fThe output with the set resolution or vertical scanning frequency may not be possible depending on the computer or video device in use.
[SDI IN]
(Only for PT- RZ970)
Set this item in accordance with the signal input to the  terminal.
Setting [SIGNAL LEVEL]
Select the amplitude of the signal to input.
1)
 
Press 
 as to select [SDI IN].
2)
 
Press the  button.
 fThe 

[SDI IN] screen is displayed.
3)
 
Press 
 as to select [SIGNAL LEVEL].
4)
 
Press 
 qw to switch the item.
[64-940] Normally use this setting.
[4-1019] Select this item when gray is displayed as black.
Setting [BIT DEPTH]
1) Press as to select [SDI IN].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
110 - ENGLISH
2) Press the  button.
 fThe 

[SDI IN] screen is displayed.
3)
 
Press 
 as to select [BIT DEPTH].
4)
 
Press 
 qw to switch the item.
[AUTO] Automatically selects [12-bit] or [10-bit].
[12-bit] Fixes to [12-bit].
[10-bit] Fixes to [10-bit].
Setting [3G-SDI MAPPING]
1) Press as to select [SDI IN].
2)  
Press the  button.
 fThe 

[SDI IN] screen is displayed.
3)
 
Press 
 as to select [3G-SDI MAPPING].
4)
 
Press 
 qw to switch the item.
[AUTO] Automatically selects [LEVEL A] or [LEVEL B].
[LEVEL A] Fixes to [LEVEL A].
[LEVEL B] Fixes to [LEVEL B].
Note
 fThis item does not operate during SD - SDI or HD - SDI signal input.
[ON-SCREEN DISPLAY]
Set the on-screen display.
Setting [OSD POSITION]
Set the position of the menu screen (OSD).
1)
 
Press 
 as to select [ON-SCREEN DISPLAY].
2)
 
Press the  button.
 fThe 

[ON-SCREEN DISPLAY] screen is displayed.
3)
 
Press 
 as to select [OSD POSITION].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[2] Sets to the center left of the screen.
[3] Sets to the bottom left of the screen.
[4] Sets to the top center of the screen.
[5] Sets to the center of the screen.
[6] Sets to the bottom center of the screen.
[7] Sets to the upper right of the screen.
[8] Sets to the center right of the screen.
[9] Sets to the bottom right of the screen.
[1] Sets to the upper left of the screen.
Setting [OSD ROTATION]
Set the orientation of the menu screen (OSD).
1)
 
Press 
 as to select [ON-SCREEN DISPLAY].