Panasonic Pt D9610U Projector User Manual
Have a look at the manual Panasonic Pt D9610U Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
51 Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select SHIFT. Press the ENTER button. ... The SHIFT screen will be displayed. Press the UP, DOWN, LEFT and RIGHT ( , , and ) arrow buttons to adjust the picture position. Press the MENU button three times. • The on-screen display will disappear and the screen will return to the normal state..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 104*5*0/ 4)*5 4*;& #-, $-0$,1)4& */1653&40-65*0/ $-.1104*5*0/ ,&:450/& &%(&#-&/%*/( .&/6 46#.&/6 &/5&3 &9*5 .&/6 4)*5 7 ) %+645 &9*5 .&/6 Adjusting the picture position If the button is pressed, the picture moves to the right.If the button is pressed, the picture moves to the left. If the button is pressed, the picture moves to the up.If the button is pressed, the picture moves to the down. »When adjusting the vertical position¼ »When adjusting the horizontal position¼
52 Adjusting the blanking Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select BLK. Press the ENTER button. ... The BLK screen will be displayed. Press the control level buttons ( +and −) to select the desired BLK mode from those indicated below. UPPER, LOWER, LEFT, RIGHT Press the UP ( ) and DOWN ( ) arrow buttons to adjust UPPER and LOWER, or Press the LEFT ( ) and RIGHT( ) arrow buttons to adjust LEFT and RIGHT. • The adjustment values will change from 0 (min.) to 511 (max.)..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 104*5*0/ 4)*5 4*;& #-, $-0$,1)4& */1653&40-65*0/ $-.1104*5*0/ ,&:450/& &%(&#-&/%*/( .&/6 46#.&/6 &/5&3 &9*5 .&/6 #-,611&3 611&3 OOOO -08&3 OOOO -&5 OOOO 3*()5 OOOO 4&-&$5
53 • If the black portions of the picture are fractured or tinged with green, adjust the clamp position its optimum state. Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select CLAMP POSITION. • The clamp position can be adjusted when an RGB signal has been input with the analog RGB module (ET-MD95RGB) Press the ENTER button. ... The CLAMP POSITION screen will be displayed. Press the LEFT ( )and RIGHT ( ) arrow buttons to adjust. • The adjustment values will change from 0 (min.) to 254 (max.) Optimum value for clamp position adjustment • If the black sections are fractured → The optimum value is when the fracturing of the black sections is at a minimum. • If the black sections are tinged with green→ Optimum value is when the green portion turns black but is not smudged. The projector has a picture mute capability that allows you to put the image off instantaneously. To mute the image, press the PIC-MUTE button on the projector or remote control. To reset picture mute, press the PIC-MUTE button a second time..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 104*5*0/ 4)*5 4*;& #-, $-0$,1)4& */1653&40-65*0/ $-.1104*5*0/ ,&:450/& &%(&#-&/%*/( .&/6 46#.&/6 &/5&3 &9*5 .&/6 $-.1 104*5*0/ 104*5*0/.*/ %+645 &9*5 .&/6 Adjusting the clamp position Picture mute function NOTE
54 • The KEYSTONE adjustment allows you to compensate for pictures’ horizontal trapezoidal distortion. (Keystone adjustment can not carried out in built-in test pattern.) Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select KEYSTONE. Press the ENTER button. ... KEYSTONE screen will be displayed. Press the LEFT ( )and RIGHT ( ) arrow buttons to correct horizontal keystone (trapezoidal distortion). • The adjustment values will change from 0 (min.) to 200 (max.) Press the UP ( ) and DOWN ( ) arrow buttons to adjust vertical linearity. • The adjustment values will change from 0 (min.) to 255 (max.) • Adjust vertical linearity after adjusting horizontal keystone. The variable range of V LINEARITY changes with the H KEYSTONE adjustment setting. • To reset H KEYSTONE and V LINEARITY to their respective factory default settings (H KEYSTONE:100 and V LINEARITY: 25), press the Standard (STD) button on the remote control. • H KEYSTONE and V LINEARITY settings are reflected to other input signals as well. • The keystone adjustment can compensate for trapezoidal distortion that corresponds to the projector’s elevation angle (to the screen) to within ± 10 °. • As indicated below, two types of modes can be selected for keystone correction of luminance- bandwidth-chrominance (YUV) signals (For the RGB system, there is only keystone correction using digital processing). YUV KEYSTONE:REAL: The original images are preserved as they are after keystone compensation thanks to digital processing. YUV KEYSTONE:BLANKING: Keystone correction is done with blanking, so part of the image information is lost, but there is no image degradation. (In BLANKING mode, the adjustment range in blanking adjustment (page 52) is 0 to 255)..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 104*5*0/ 4)*5 4*;& #-, $-0$,1)4& */1653&40-65*0/ $-.1104*5*0/ ,&:450/& &%(&#-&/%*/( .&/6 46#.&/6 &/5&3 &9*5 .&/6 ,&:450/& ),&:450/& 7-*/&3*5: :67,&:450/&#-/,*/( 4&-&$5 – %+645 &9*5 .&/6 Adjusting the keystone(Trapezoidal distortion) Press and hold the right arrow button until both sides of the frame become completely vertical. In case of over- adjustment, use the left arrow button to step back. YUV signals:Includes the Video Signal module, Digital Serial Signal module, analog YPBPR(YCbCr) input, and analog RGB input all placed in RGB REALITY mode. NOTE
55 Adjusting the picture to the desired setting The following procedures can be used to adjust the picture to the desire appearance. Adjustment procedure ... Adjusting the COLOR setting Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select COLOR. Press the ENTER button. ... The COLOR individual adjustment screen will be displayed. Use the control level buttons ( +and −) to adjust the COLOR setting level. *1.The functions of the LEFT ( ) and RIGHT ( ) arrow buttons change depending on the adjustment item selected. Refer to the table below for details. If you would like to adjust the BRIGHT, CONTRAST and TINT settings, repeat steps , and . *2.If adjusting the BRIGHT and CONTRAST settings, the individual adjustment screens can be displayed by pressing the respective buttons on the remote control unit. • If approximately five seconds pass without any buttons being pressed while an individual adjustment screen is being displyed, the display will return to the PICTURE screen..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 1*$563& $0-03 5&.1
56 Adjusting the white balance (High / Low) Adjustment procedure (Project a signal to be adjusted) Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select COLOR TEMP. Press the LEFT ( ) and RIGHT ( ) arrow buttons to select the desired setting from those indicated below. LOW, MID, HIGH, USER, DYNAMIC 〈 If you would like to further adjust the white balance〉 Select USER in step . Press the ENTER button. ... •The WHITE BALANCE HIGH (LOW) screen will be displayed. Press the ENTER key to switch between WHITE BALANCE HIGH and WHITE BALANCE LOW. Press the UP ( ) and DOWN ( ) arrow buttons to select either R, G or B. Use the control level buttons ( +and −) to adjust the setting level. • If these adjustments are not made correctly, none of the colors will be reproduced correctly. • If you make an error in adjustment so that the colors do not match correctly, press the STD button while one of the individual adjustment screens is being displayed. Only the item being displayed will be reset to the factory pre-settings. • The projection of a built-in test pattern (Refer to page 65.) does not allow the white balance adjustment. Be sure to project an external input signal for this adjustment. Adjusting the picture to the desired setting (continued) 1*$563& $0-03 5&.1
57 NOTE Adjusting the picture quality The following procedures can be used to adjust the picture quality to the desired setting. Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE. Press the ENTER button. ... The PICTURE screen will be displayed. • If a or indicator is shown at the bottom or top of the adjustment items list in the PICTURE window, it indicates that the remaining part of the list can be scrolled up or down in the window. Use the UP or DOWN arrow button ( ) to scroll the list. Press the UP ( ) and DOWN ( ) arrow buttons to step through the adjustment items list until you reach the target item. Press the LEFT ( ) and RIGHT ( ) arrow buttons to change the current setting. • For available adjustment items and settings, see the table on the next page..&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 1*$563& $0-03 5&.1
58
• NR (noise reduction) settings cannot be adjusted for analog RGB input and TMDS input.
• The FILTER adjustment is ineffective for XGA (1 024 x 768) mode on the PT-D9510U, or SXGA (1 280
x 1 024) mode on the PT-D9610U. It is also ineffective for any video input mode other than analog
RGB and TMDS modes, or if “THROUGH” is chosen for the SIZE mode (see pages 60 and 61).
• Even with the above signal, adjustment is possible during keystone correction. Even with YUV type
signals, adjustment is possible during REAL keystone correction.
• FRAME RATE is effective only for analog RGB,and 1080/30p, 1080/25p, 1080/24p, and 1080/24sF
video signal formats of HD serial.
• PAL CINEMA is effective only for the 576i, 1 080/50i PAL (or SECAM) standard.
• PAL CINEMA will cause degraded picture quality (lowered vertical resolution) if used for signals other
than those pulled down at a 2:2 ratio.
• For 480p, 480i or 576i scan format, SHARPNESS H defaults to 6.
SHARPNESS H
SHARPNESS V
NR
(Noise Reduction)
GAMMA MODE
FILTER
FRAME RATE
PAL CINEMA
Adjustment ItemOperation
Adjustment Details
Nine steps from OFF to 8 (factory default : 2)
A larger value causes a greater effect
Four steps from OFF to 3 (factory default : 2)
A larger value causes a greater effect
OFF: No correction
1 : Weak
2 : Medium (factory default)
3 : Strong
A larger value causes a greater effect
Two steps of 2.2 and 2.5 (factory default : 2.2)
Five types from 0 to 4 (factory default : 2)
0 : Gives priority to contrast.
4 : Restricts the loss in picture information to a minimum.y
24p 60p / 24p 24p
(factory default: 24p 60p)
25p 50p / 25p 25p
(factory default: 25p 50p)
30p 60p / 30p 30p
(factory default: 30p 60p)
24sF 60p / 24sF 24p / 24sF 48i
(factory default: 24sF 60p)
OFF : No cinema processing
AUTO : Auto detection (factory default)
ON : Cinema processing (see the following notes)
Makes the horizontal contours sharper.
Makes the vertical contours sharper.
Selects the noise reduction effectiveness.
Selects the gamma mode.
For the PT-D9510U, use this adjustment to
select interpolation filter settings for signals
other than XGA. For the PT-D9610U, use this
adjustment to
select interpolation filter settings
for signals other than SXGA.
Use this adjustment to choose the best
frame rate conversion for minimum flicker
on individual HDTV signal input.
Use this adjustment to further enhance
vertical resolution when a 576i, 1 080/50i
PAL (or SECAM) signal
is applied.
NOTE
59 Adjusting the picture size Adjustment procedure Press the MENU button. ... The MENU screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION. Press the ENTER button. ... The POSITION screen will be displayed. Press the UP ( ) and DOWN ( ) arrow buttons to select SIZE. Press the ENTER button. ... The SIZE screen will be displayed. Press the control level buttons ( +and −) to select the desired size mode from those indicated below. DEFAULT, THROUGH, H-FIT, V-FIT, HV-FIT, ZOOM •“4:3”, “16:9” ----- Modes other than the analog RGB or TMDS input allow the selection. Size modes DEFAULT • • •The input signal is projected with the aspect ratio unchanged. THROUGH •The input signal is projected with the resolution unchanged. H-Fit • • • • • • • • • • •The input signal is projected with all horizontal panel picture elements used. For signals with a aspect ratio which is vertically longer than 4:3(for the PT-D9510U)/ 5:4(for the PT-D9610U), the top and bottom edges of the picture are cropped. V-Fit • • • • • • • • • •The input signal is projected with all vertical panel picture elements used. For signals with a aspect ratio which is horizontally longer than 4:3(for the PT-D9510U)/ 5:4(for the PT-D9610U), the left and right edges of the picture are cropped. HV-Fit • • • • • • • •The input signal is converted to an aspect ratio of 4:3(for the PT-D9510U) / 5:4(for the PT-D9610U). For signals with an aspect ratio other than 4:3(for the PT-D9510U) / 5:4(for the PT-D9610U), circles in the picture become distorted, etc. For signals with an aspect ratio other than 5:4 circles in the picture become distorted, etc. ZOOM • • • • • • • •The enlargement ratio of the picture is changed. The enlargement ratio in both the horizontal and vertical directions can be changed to between 50 % and 999 %(except analog RGB, TMDS input), between 75 % and 999 %( up to SXGA of analog RGB, TMDS input),between 100 % and 999 %(UXGA of analog RGB, TMDS input) with the top-left corner of the screen as the reference point. 4:3 • • • • • • • • • • • •The input signal is projected with the aspect ratio 4:3. 16:9 • • • • • • • • • • •The input signal is projected with the aspect ratio 16:9. • An overscan of 7 % is applied to all modes other than analog RGB input and TMDS input. • The 4:3 and 16:9 mode are only for YUV type signal input .&/6 650 4&561 -&/4 1*$563& 104*5*0/ 015*0/ 4*(/--*45 5&45 155&3/ .&/6 46#.&/6 &/5&3 &9*5 .&/6 104*5*0/ 4)*5 4*;& #-, $-0$,1)4& */1653&40-65*0/ $-.1104*5*0/ ,&:450/& &%(&#-&/%*/( .&/6 46#.&/6 &/5&3 &9*5 .&/6 4*;&ÎÎÎÎÎÎÎ ) OOO
60 Screen examples for different size settings (For PT-D9510U) INPUT PICTURE Default Through H-Fit V-Fit HV-Fit85 ¢640·400£43 ¢1152·864£54 ¢1280·1024£ SIZE SETTING The picture is displayed at maximum size while maintaining the original aspect. * If the picture extends outside the screen, the top-left corner is used as the reference point.