Panasonic System Controller Wv Cu360c Operating Instructions

							31
Digital Disk Recorder Control
A Digital Disk Recorder is controlled from the System Controller using shortcuts assigned to numeric buttons. 
For more information, refer to the manual included with the Digital Disk Recorder. 
The operating procedures on the following pages assume that you have selected a system unit and a monitor.
WJ-HD100 Shortcuts
The shortcuts listed below are available for controlling a digital disk recorder. For more details, refer to the Operating
Instructions included with the digital disk recorder.
Item
SHIFT
SETUP
FUNCTION
Step Playback REW. Play/Stop Selected Alarm
Record Show/Hide SETUP MENU
The top of the oldest record will be
accessed. Jump to Oldest.
UP
LR
UP
DOWNR
WV-CU360C
Setup Item Selection
Parameter Selection
Move Cursor Back A Step
Show/Hide Alarm History
Search Alarm HistoryWJ-HD100 Note
Button lock is released automatical-
ly by opening the setup menu.
Operate LCD Button.
STOPSETUP/ESCHold down
2 seconds
STEP
/
PUSH–   PAUSESET//
PUSH–   PAUSESET//
STOPSETUP/ESC
STOPPLAYCAMMON
ESC SET
REW/FF
/
SETUP
FUNCTION
Hold down
2 seconds
DOWN LR
UP
LR
DOWN LR
UP
DOWN LR
MON
ESCALM RESET
ALM RECALLSHIFT
RecordingRECSETUP
FUNCTIONSHIFT
Stop
Stop Playback
Stop RecordingSTOPSETUP/ESC
STOP
STOP
SETUP
FUNCTIONSHIFT
PlaybackPLAYSETUP
FUNCTIONSHIFT
PausePUSH–   PAUSESET//SETUP
FUNCTIONSHIFT
Step Playback FWD.PUSH–   PAUSESET//STEP/
PUSH–   PAUSESET//STEP/
SETUP
FUNCTIONSHIFTSETUP
FUNCTIONSHIFT
Skip Playback FWD.PUSH–   PAUSESET//REW/FF/SHIFT
SETUP
FUNCTION
Skip Playback REW.PUSH–   PAUSESET//REW/FF/
Jump to Latest.
The top of the latest record will be
accessed.PUSH–   PAUSESET//REW/FF/Press 
JogDial
SETUP
FUNCTIONSHIFTPUSH–   PAUSESET//REW/FF/Press 
JogDial
SETUP
FUNCTIONSHIFT
SETUP
FUNCTIONSHIFT
SHIFT
SETUP
FUNCTION
Exclusive use to stop playback.
Exclusive use to stop recording.
Hold down
2 secondsHold down
2 seconds
Press
JogDial
Press
JogDial 
						

							32
SETUP
FUNCTIONSHIFT
WJ-HD500A Shortcuts
The shortcuts listed below are available for controlling a digital disk recorder. For more details, refer to the Operating
Instructions included with the digital disk recorder.
DAYLIGHT SAVINGS
OFF, INT or EXT selectable
Operate LCD Button. Item WV-CU360CWJ-HD100 NoteDAYLIGHT
SAVINGS
SHIFT
SETUP
FUNCTION3 1
Timer REC Mode
Selection
SHIFT
SETUP
FUNCTION
Button Lock OFFOperate LCD Button. Operate LCD Button.
Button Lock ON
SHIFT
SETUP
FUNCTION31
SHIFT
SETUP
FUNCTION30
Item Controller Operation Note
Step Playback FWD
Step Playback REW
Pause
Playback
Recording
Stop 
Stop Playback
Stop Recording
Alarm Search OFF
Alarm Search ON
Button Lock OFF
Button Lock ON
Daylight Savings ON/OFF
Timer Mode Selection
Record List Display ON/OFF
Record Search Window ONEqual to REC button
For both Manual Recording and Playback
Exclusive use to stop playback
Exclusive use to stop recording
Internal, External, Off
Index
Index/Shuttle
SETUP
FUNCTIONSHIFTSETUP
FUNCTIONSHIFT
SETUP
FUNCTIONSHIFT
SETUP
FUNCTIONSHIFT
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION33
SETUP
FUNCTIONSHIFTSETUP
FUNCTIONSHIFT
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION31
SHIFT
SETUP
FUNCTION30
SHIFT
SETUP
FUNCTION3 1
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION 
						

							33
Item Controller Operation Note
Screen Display ON/OFF
Group Selection
Show/Hide Alarm Log
Skip Playback FWD.
Skip Playback REW.
Record List 1 line Up
Record List 1 line Down
Record List Turn Next Page
Record List Turn Prev. Page
Playback of Selected Record
Backward Search in Window 
Forward Search in Window
Increment Parameter in Window
Decrement Parameter in Window
Search Window Display ON/OFF
Alarm Log 1 line Up
Alarm Log 1 line Down
Playback of Selected Alarm
Record
Backward Search in Window 
Forward Search in Window
Increment Parameter in Window
Decrement Parameter in Window
Search Window Display
SelectionSpeed change 1/2, 1, 2, 5
Speed change 1/2, 1, 2, 5
Record List
Record List
Record List
Record List
Record List
Record List
Alarm Log
Alarm Log
Alarm Log
Alarm Log
Alarm Log
Time & Date, Alarm CH, OFF
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
ALM RESET
ALM RECALL
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
CAM
SET
SHIFT
EL-ZOOM
+
SHIFT
STILL
–
SHIFT
MON
ESC
DOWN LRUP
LR
UP
DOWNR
UP
DOWN LR 
						

							34
Item
Alarm Operation
When the WV-CU360C receives an alarm signal from a sys-
tem unit, the alarm indicator on the controller blinks.
The alarm indicator changes from blinking to steady light
when the alarm is automatically reset.
The camera number [---] appears in the camera section of
the LED display.
Alarm Reset
1. Press the ALM RESET/ALM RECALLbutton.
The alarm indicator on the controller goes off.
Notes:
• Alarm reset operations including auto reset are
applied to all system units, not to a selected one.
• Alarm reset mode differs depending on the system
unit connected to the WV-CU360C.
• Confirm that the SHIFT button is released.
Alarm Suspension
The alarm suspension mode is activated or deactivated.
Use this function when you do not want to be disturbed by
alarm input as for example during setup operations.
1. Press the ALM SUSPENDbutton. The ALM SUSPEND
indicator lights up.
Alarm input is ignored while the indicator is lit.
ALM RESET
ALM RECALL
ALM SUSPEND
2. To cancel alarm suspension, press the ALM SUSPEND
button again.
Note:The alarm suspension is applied to all system
units, not to a selected one.
Alarm Recall
The alarm event log is recalled and displayed on the moni-
tor.
1. Select the desired system unit and monitor.
2. Press the ALM RESET/ALM RECALLbutton while the
SHIFTindicator is lit. The ALM RECALLindicator lights
up. The alarm log appears on the monitor.
3. To cancel the alarm recall function, press the ALM
RESET/ALM RECALLbutton while the SHIFTindicator
is lit.
ALM SUSPEND
ALM RESET
ALM RECALLSHIFT
Controller Operation Note
Copy to DVD
Copy Cancel
DVD Copy Record Display Equal to EL-ZOOM
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION
SHIFT
SETUP
FUNCTION 
						

							35
REMOTE SETUP of UNITS & CAMERAS
You can set up the system unit and the camera with the
setup menu by this controller.
You can use the controller to set up system units and cam-
eras.
This section describes the main remote setup procedures.
Some of the descriptions may not be applicable if they refer
to devices not equipped in your system.
For further information on the default settings and operating
procedures, refer to the Operating Instructions included
with the individual units.
System Unit Setup
1. Select the desired system unit compatible with PS•Data
mode.
2. Press the SETUP/FUNCTIONbutton for more than 2
seconds. The SETUPindicator lights up.
The Setup menu for the system unit appears on the
monitor.
3. To complete the setup, press the SETUP/FUNCTION
button for 2 seconds or more.
The SETUP indicator goes off.
Note:If you change the default baud rate or parity check,
the system unit setup function is disabled.
Keys used for system unit setup
Example of Setup Menu for WJ-MP204C
WJ-MP204C SETUP MENU x.xx
   COMMUNICATION
   SYSTEM
Camera Setup
1. Select the desired camera.
2. Press the CAM SETUP/CAM FUNCTIONbutton for 2
seconds or more to access the Camera Setup menu.
The CAM SETUPindicator lights up.
3. Move the cursor with the numeric buttons 2 (Up) or 8
(Down), then select a parameter with the buttons 6
(Right) or 4 (Left).
4. Press the CAM/SETbutton to execute the parameter or
enter a submenu.
5. To return to the previous menu, press the MON/ESC
button.
6. Press the CAM SETUP/CAM FUNCTIONbutton for 2
seconds or more to complete the camera setup.
   *** SET UP MENU ***
PRESET 1*
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 LOCAL/REMOTE
 SPECIAL1
CAMERA
RS485 SET UP15
10MIN
AUTO PAN
SEQ
OFF
LOCAL
(Example of Camera Setup menu)
MONCAM
LOGOUT
ESC SET
MONCAM
LOGOUT
ESC SETTo move the cursor.
To select a parameter.
To execute the parameter or
enter a submenu
To return to the previous menu
CAM
SET
MON
ESC
DOWN LR
UP
LR
EL-ZOOMSTILL
–
+
FUNCTION
SETUP
CAM FUNCTION
CAM SETUP 
						

							36
Camera Patrol Learning
There are two ways of setting up camera patrol learning.
One is to use the camera setup menu and the other is to
operate the camera.
Follow the procedures below to set up while operating the
combination camera.
1. Select the desired system unit, monitor and combina-
tion camera.
2. Press the PATROL PLAY/PATROL LEARNbutton
while holding down the PROGRAM/CAM SETUP/CAM
FUNCTIONbutton.
[LEARNING] appears on the monitor.
3. Operate the camera using the following controls so that
it traces a routine course most frequently patrolled. The
learning is programmed for 30 seconds for later patrol
play.
• Pan/Tilt (Joystick)
• Iris (Open/Close)
• Focus (Far/Near)
• Zoom (Tele/Wide)
• Preset Position
Note:The memorized parameters may differ somewhat
depending on the camera type. Refer to the manual
included with the camera.
4. To stop the learning, press the SEQUENCE/PATROL
STOPbutton while holding down the PROGRAM/CAM
SETUP/CAM FUNCTION button.
[LEARNING] disappears from the monitor. 7. Move the cursor to [SPECIAL] on the Setup menu, and
press numeric buttons 4and 6simultaneously for 2
seconds or more to display the special menu. 
8. Move the cursor to [CAMERA RESET]* on the Setup
menu, and press buttons 4, 5and 6simultaneously to
reset all the functions to the defaults.
*The menu to reset the camera functions differs depend-
ing on the camera:
[SPECIAL] for the WV-CS650, [SPECIAL 2] for the WV-
CS854, and [END] for fixed cameras etc.
Notes:
• If camera setup is started using the buttons on the
camera, all future operations for setup must be per-
formed using the buttons on the camera.
If camera setup is started using the System
Controller, all future operations for setup must be
performed using the same controller.
• For further information, refer to the Operating
Instructions for the selected camera.
Keys used for camera setup 
LEARNING28
4
6To move the cursor
To select a parameter
To execute the mode or
enter a submenu
To return to the previous menu
CAM
SET
MON
ESC
CAM FUNCTION
CAM SETUP
PROGRAM
CAM FUNCTION
CAM SETUP
PROGRAMPATROL PLAY
PATROL
LEARN
SEQUENCE
PATROL
STOP 
						

							37
Camera Preset Position
There are two ways of presetting camera positions.
One is to use the camera setup menu of the combination
camera and the other is to operate the System Controller as
follows.
1. Select the desired system unit, monitor and camera.
2. Move the camera to a position you wish to preset, using
the joystick.
Adjust the picture using the following buttons.
• Iris (Open/Close)
• Focus (Far/Near)
• Zoom (Tele/Wide)
Note:The memorized parameters may differ somewhat
depending on the camera type. Refer to the manual
included with the camera.
3. Type a number with the numeric buttons for the pre-
set position. The typed number appears in the
CAMERA section of the LED display.4. Press the HOME/PRESET/PROGRAM PRESETbutton
while holding down the PROGRAM/CAM SETUP/CAM
FUNCTION button.
The position and its number are memorized for later
recall.
UP
LR
DOWN
MONCAM
LOGOUT
ESC SET
HOME/PRESET
PROGRAM
PRESET
CAM FUNCTION
CAM SETUP
PROGRAM 
						

							39
For WJ-FS616C
Multiplexer System 
						

							40
MAJOR OPERATING CONTROLS & THEIR FUNCTIONS 
Front View (Template for WJ-FS616C)
System ControllerOPERATE LOCK ALARM
SPOT
AUTO/+IRIS
CLOSE OPEN
NEAR FAR
TELE WIDE
FOCUS
ZOOM IRIS RESET
VTR
CAM MULTI
SCREENSEQUENCE
EL-ZOOMMULTI SELECT
STILLPRE-POSI
ALT
ALM RESET
ALM SUSPEND
FUNCTION
ALL RESET
CAMERA SET
ON OFF ON/OFF
SETUPAUTO
FOCUS HOME/-UNITCAM
ESC SET
UP
LR
DOWN
UNITCAMERA
For Multiplexer
WV-CU C360
T/L MODE
CAMERA SITE CONTROL
AUX 2
AUX 1
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
qwert
yuio!0!1!2!3!4
qOperate Indicator (OPERATE)
Is lit while power is supplied to the System Controller.
wLock Indicator (LOCK)
Is lit while operation of the System Controller and WJ-
FS616C is prohibited by the connected computer.  The
lock can be released by sending a command from the
computer.
eAlarm Indicator (ALARM)
Blinks when an alarm is activated. Blinking changes to
steady light when the alarm is automatically reset.
To turn the indicator off, press the ALM RESETbutton.
rLED Display (UNIT CAMERA)
LED display allowing you to confirm the number of the
system unit and camera in operation. The CAMERA
section will display “–” when operating in multiscreen or
sequence mode.
tIris buttons (IRIS, CLOSE/OPEN)
Close or open the lens iris of cameras equipped with
the specified lens.
When these buttons are pressed at the same time, the
lens iris is reset to the factory setting.yJoystick Controller (UP/DOWN/L/R)
Used to operate the pan/tilt head manually, or to move
the cursor to the desired position in the setup menu of
the Video Multiplexer.
UP: Upward
DOWN: Downward
L: Left
R: Right
uFocus buttons (FOCUS, NEAR/FAR)
Adjust the lens focus of cameras equipped with the
specified lens.
iZoom buttons (ZOOM, TELE/WIDE)
Zoom cameras equipped with the specified lens.
oAuto/Increment button (AUTO/+)
Activates the auto panning function.
During the setup, this button is used to select the
desired parameter in the setup menu. 
						

							41
!0Home/Decrement button (HOME/–)
Moves the camera to the home position.
During the setup, this button is used to select the
desired parameter in the setup menu.
!1Auto Focus button (AUTO FOCUS)
Activates the auto focus function when the specified
camera with auto focus feature is selected.
!2Camera/Set button (CAM/SET)
CAM:Selects a camera. Enter a camera number with
the numeric buttons, then press the CAM/SET but-
ton.
SET:Executes the currently highlighted setting in the
setup menu.
!3Numeric Buttons (0 - 9)
These buttons are used for numeric input into the sys-
tem, such as the number of a camera you want to
select.
!4Unit/Escape button (UNIT/ESC)
UNIT:Selects a WJ-FS616C unit. Enter a unit number
with numeric buttons, then press the UNIT/ESC but-
ton.
ESC:Escapes from the currently highlighted selection
and return to the previous menu window in the
setup.
!5Alternate button (ALT)
In combination with certain other buttons, activates spe-
cial functions.
For example, in combination with the ALM SUSPEND,
EL-ZOOM or MULTI SELECT button, it is used to control
the VTR (VCR).
!6Multiscreen Monitor button (MULTI SCREEN)
Selects the multiscreen monitor connected to the MUL-
TISCREEN OUT connector of the Video Multiplexer.
The indicator lights up when the multiscreen monitor is
selected.
Note:When REC OUT of the Video Multiplexer is used
as connector for the Multiscreen 2 Monitor, this but-
ton alternately selects the Multiscreen or
Multiscreen 2 Monitor.
The indicator blinks when the Multiscreen 2 monitor
is selected.
!7Spot Monitor button (SPOT)
Selects the spot monitor connected to the SPOT OUT
connector of the Video Multiplexer.
The indicator lights up when the spot monitor is select-
ed.!8Alarm Reset button (ALM RESET)
Cancels an active alarm.
Pressing this button while the alarm function is activat-
ed will reset an alarm of the currently selected unit and
return the system to the condition before the alarm
function was activated.
Pressing it in combination with the ALT button will reset
all alarms.
!9Sequence button (SEQUENCE)
Activates the sequence mode. In this mode, a series of
camera pictures is displayed in succession on the mon-
itor screen for the specified duration.
The indicator lights up when this mode is selected.
@0VTR (VCR)/Camera selection button (VTR/CAM)
Selects the camera picture or VTR (VCR) playback pic-
ture for display on the multiscreen monitor.
The indicator lights up when the VTR (VCR) mode is
selected.
Note:The above operation is not valid unless multi-
screen monitor is selected using the MULTI-
SCREEN button.
@1Alarm Suspend button (ALM SUSPEND)
Pressing this button for more than two (2) seconds sus-
pends activation of the alarm without changing the cur-
rent alarm mode setup.
The indicator lights up when the alarm suspension
mode is selected.
@2Electronic Zoom button (EL - ZOOM)
Zooms the picture presently displayed on the multi-
screen monitor.
@3Multiscreen Selection button (MULTI SELECT)
Selects the multiscreen pattern to be displayed on the
multiscreen monitor while monitoring the camera pic-
ture or VTR (VCR) playback picture.
Pressing this button repeatedly will switch the screen as
follows:
Camera Picture:
4 →7 →9 →10 →13 →16→4 screen segments
VTR (VCR) Playback Picture:
4 →9 →16→4 screen segments
@4Function button (FUNCTION)
Displays the VTR (VCR) playback picture with the cam-
era pictures on the multiscreen monitor.
The indicator lights up when the combined mode is
selected, and turns off when the playback picture is
selected.
During the setup, this button is used to select the next
page.