Panasonic System Controller Wv Cu360c Operating Instructions

							73
SETUP PROCEDURES (For System 850)
To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the
controller as described below.
Prior to Setup
Do the following before entering the setup mode.
1. Confirm that all necessary connections and switch set-
tings are complete.
2. With the power turned off, move bit #6 of the MODE
switch on the rear to ON (administrator) position.
3. Supply power to the controller.
4. Turn on the power of cameras and other system units.
5. The LCD displays [SEtUP]. The controller is ready to
enter the setup mode.
When setup is completed, restore the switch to its original
position.
1. With the power turned off, move bit #6 of the MODE
switch on the rear to OFF (operator) position.
2. Supply the power to the controller.
Buttons and Controls used for Setup
The following buttons and joystick operations are used for
setup.
DC 9V IN
MODE
1 234 5678
OFF
ON
MODE
12345678
OFF
ON
Operator mode
Administrator mode
0
9Numeric buttons: To select a parameter
CAM (ENTER) button: To execute modes
and parameters
To enter a submenu
CLEAR (ESC) button: To return to the previ-
ous menu
CAMERA
(ENTER)
AUTO
PA N
DOWN LRUP
LR
UP
DOWNR
UP
DOWN LR
Up: To select a setup menu
Down: To select a setup menu
Left: To decrease the parameter
Right: To increase the parameter 
CLEAR
(ESC)
EXIT 
						

							74
Setup Procedures
Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
Menu 
Selection
Move Joystick 
UP and down 
to selectSetup Menus
Parameter Selection (default*)
LED Display
blinking
Setup
Administrator
Password
Prompt
Speed
ParityInitial
Display
Authorization
Baud Rate
(bps)Press
twice
Parity Check
CAM
SET
CAM
SET
MON
ESC
LED prompts you to enter pass-
word
Enter a 5-digit password, 
press                 (12345*)
(1) 2 400  (2) 4 800  (3) 9 600*
(4) 19 200
(1) None*   (2) Even Reading Function
OK No
DOWN LRUP
LR
CAM
SET
Administrator Authorization
1. Press the CAMERA (ENTER)button while [SEtUP] is
displayed.  The [- - - - -] prompt appears.
2. Enter a password using the numeric buttons, then press
the CAMERA (ENTER)button.
The default setting is [12345].
3. If the password entered is valid, [SPEED] appears.  If
password entry failed, the menu returns to [SEtUP].
Baud Rate
In this menu, the communication speed (bps: bits per sec-
ond) is selected.  The communication speed should match
that of the WJ-SX850.
1. Display [SPEED], and press the CAMERA (ENTER)
button twice.
2. Select a parameter entering a bracket-enclosed num-
ber, e.g., (3), moving the joystick.
The default setting is 9 600 bps.
(1) 2 400:2 400 bps
(2) 4 800:4 800 bps
(3) 9 600:9 600 bps
(4) 19 200:19 200 bpsNote:Selecting a slower rate (e.g., 2 400 bps) will
delay the response time (e.g., the time until an acti-
vated alarm is reset).
3. Press the CAMERA (ENTER)button to validate the
selection.
4. Press the CLEAR(ESC)button to return to the [SPEED]
menu.
Parity
In this menu, the parity check mode is selected.
1. Display [PrtY] and press the CAMERA (ENTER)button
twice.
2. Select a parameter with the joystick.
The default setting is None.
n:None
E:Even parity
3. Press the CAMERA (ENTER)button to validate the
selection.
4. Press the CLEAR(ESC)button to return to the [SPEED]
menu.
Note:The baud rate and parity check mode of the WJ-
SX850 and the controller must be the same, otherwise
data communications will not function. 
						

							75
OPERATING PROCEDURES (For System 850)
Login & Logout
Login
1. Turn on the power switches of all system components.
2. Turn on the power of the WV-CU360C System Controller
by connecting the AC adapter to the AC outlet.
The OPERATE indicator lights up and “NO USER” will
appear on the LED display of the System Controller.
3. Enter your registered Operator ID number (up to 5 dig-
its) using the numeric buttons, then press the [CAM-
ERA (ENTER)]button.  The underline appears on the
LED display.
4. Enter your registered Password (up to 5 digits) using
the numeric buttons, then press the [CAMERA
(ENTER)]button.
If the operator ID and password entered are valid, the
LED will display “READY”.Note:If login has failed (operator or password error), the
PROHIBITED indicator on the controller will light up and
“NO ACCESS” will blink on the LED display for about 3
seconds. Then the login procedure returns to the start.
Logout
1. While holding down the LOG OUTbutton, press the
[CAMERA (ENTER)]button . 
“NO USER” is displayed on the LED display.
PROGRAM
PRESET
CALL
PRESET
AUX1 OFF
CAM ID
AUX1 ON
GEN
WIPER
AUX2 OFF
MON STATUS
AUX2 ON
ALL
SHIFTCLEAR
(
ESC)DEF OFFDEF ONCAMERA
(
ENTER)
AUTO
PA N
123
456
78
09
PROGRAM
PRESET
CALL
PRESET
AUX1 OFF
CAM ID
AUX1 ON
GEN
WIPER
AUX2 OFF
MON STATUS
AUX2 ON
ALL
SHIFTCLEAR
(
ESC)DEF OFFDEF ONCAMERA
(
ENTER)
AUTO
PA N
123
456
78
09
LOG OUTCAMERA
(ENTER)
AUTO
PA N
Note: This section describes only some important operations such as login, logout, and different operations from the front
panel of the System 850. Please refer to the manual included with the System 850 for further information on camera
selection, monitor selection and so forth. 
						

							77
Appendix 
						

							78

Power Source: 9 V DC, 400 mA (Use the supplied AC Adapter only)
Data Output/Input Port: 6-conductor modular jack (RS-485, Full Duplex) x2
Switching Functions : Camera selection, Monitor Selection/Sequence
Switching of Live and Playback/Changing the Multiscreen Picture Layout/
Still/Electronic Zoom/Sequence (available for WJ-FS309/316/409/416/616/
616C)
Controller Number 1-8 (Rotary Switch)
Unit Address Selection: 1-99 (for PS
•Data), 1-16 (WJ-FS616/616C)
Monitor Number Selection: 1-99 (for PS
•Data)
Camera Number Selection: 1-199 (for PS
•Data)
Lens Functions: Iris: Open/Close/Preset (only with DC control lens)
Focus: Near/Far/Auto Focus
Zoom: Wide/Tele
Housing: Defroster: On/Off 
Wiper: On/Off
Auxiliary 1: On/Off
Auxiliary 2: On/Off
Pan/Tilt: Manual Pan: Right/Left
Manual Tilt: Up/Down
Auto Pan, Auto Sort, Auto Sequence, Random Pan, Preset Position, Home
Position, Camera Patrol
Other Camera Controls: Camera Setup
Camera Function
System Operation: Alarm (Display/Suspend/Recall/Reset)
Setup
Ambient Operating Temperature: –10˚C - +50˚C (14˚F - 122˚F)
Ambient Operating Humidity:  Less than 90 %
Dimensions: 300 (W) mm x 74 (H) mm x 177 (D) mm
[11-13/16” (W) x 2-15/16” (H) x 6 15/16” (D)]
Weight: 1.3 kg(2.9 lbs.)

Input
Power Source: 120 V AC, 60 Hz
Power Consumption: 10 W
Output
Power Source: 9 V DC
Power Consumption: 400 mA
Dimensions and weight are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
STANDARD ACCESSORIES
AC Adapter ......................................................................1 pc
6-conductor Modular Cable Assembly ............................1 pcPanel Template for WJ-FS616/616C ................................1 pc
Panel Template for WJ-SX350 .........................................1 pc
Panel Template for System 850 .......................................1 pc 
						

							79
The System Controller WV-CU360C can be reset to the
default settings.
1. Remove the DC plug of the AC adapter from the con-
troller.
2. While pressing numeric buttons 2, 4and 6simultane-
ously, plug in the DC plug.
3. When all indicators light up, resetting is completed.
Note:Keep the DC plug connected to the controller
until the reset procedure is completed. 
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
ALL RESET 
						

							N1001-0 V8QA5880BN Printed in Japan
N19 Imprimé au Japon 2001 © Matsushita Communication Industrial Co., Ltd.  All rights reserved.Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 (809)750-4300
Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America
Executive Office:One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838
Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211
Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840