Panasonic System Controller Wv Cu360c Operating Instructions

							42
@5Preset Position button (PRE - POSI)
In combination with the numeric buttons and CAM
(SET) button, moves the camera to the desired preset
position.
@6Still button (STILL)
Freezes the picture on the multiscreen monitor.
The indicator lights up when the still mode is selected.
@7Camera Set buttons (CAMERA SET ON/OFF)
Open or close the camera setup menu on the monitor
screen.
ON:Opens the selected camera setup menu on the
monitor, if applicable.
The indicator lights up when the camera setup
menu is displayed.
OFF:Closes the camera setup menu.
@8Set Up button (SET UP ON/OFF)
Opens or closes the WJ-FS616/FS616C setup menu on
the monitor. 
						

							43
INSTALLATIONS (For WJ-FS616/FS616C)
The installation should be made by qualified service personnel or system installers according to the following instructions.
Warning!
System Connections
Connection Example
The connection example shows cameras and an alarm sensor connected to the Video Multiplexer.  A time lapse VCR will
record pictures for later playback. The spot monitor and multiscreen monitor will display live and playback pictures while these
devices are being operated from System Controller WV-CU360C.
481216
371115
261014
15913
PUSH   OPEN16
POWERLOCKON
OFF
ALARMMULTI
SCREENMULTISCREENSELECT
RESET SPOT SEQUENCE
VCR
CAMCAMERA/PRESET   POSITION
Video
Data RS-485
Video Multiplexer
WJ-FS616C
Time Lapse VCR
Personal Computer
(Software) System Controller
WV-CU360CSpot Monitor
Live 1-16chMultiscreen Monitor
Live 1-16ch
Playback 1-16ch RS-232C/WiredAlarm Sensor
AUXAlarm
System ControllerOPERATE LOCK ALARMSPOTAUTO/+IRISCLOSE OPEN
NEAR FAR
TELE WIDEFOCUSZOOM IRIS RESETVTR
CAM MULTI
SCREENSEQUENCEEL-ZOOMMULTI SELECTSTILLPRE-POSI
ALTALM RESETALM SUSPENDFUNCTIONALL RESET
CAMERA SETON OFF ON/OFFSETUPAUTO
FOCUS HOME/-UNITCAM
ESC SET
UP
LR
DOWN
UNITCAMERAFor MultiplexerWV-CU C360
T/L MODE
CAMERA SITE CONTROL
AUX 2AUX 1 
						

							44
DATA Port Connection (For Multiplexer)
Data ports are connected with RS-485 cables among devices using the Camera Communication protocol as follows.
Note:When using cables other than those supplied, make sure to use shielded 4-wire twisted pair cable suitable for RS-485
communication.
•Internal Diagram
•Basic Connection
DIP Switch Setting (For Multiplexer)
An 8-bit DIP switch mounted on the rear panel specifies the communication mode, etc. The default position is marked with an
asterisk *.
System Controller
WV-CU360C
D ATA
RS-485 Cable
Termination:
ON Termination:
ON
TERM.
OFF IN OUT
OND ATA
Video Multiplexer
WJ-FS616C
DC 9V IND ATA MODE CONTROLLER No.0987654321
SW position
OFF
Not used
On*
Administrator 
Not used
Not used Function
ON
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Bit 8Unit Version
Unit Version
Unit Version
Reserved
Line termination
Operation mode
Reserved
Data transmissionSee Unit Version*
See Unit Version*
See Unit Version*
Fixed to OFF*
Off
Operator*
Fixed to OFF*
Fixed to OFF*
Data Flow
–
WJ-FS616C ← WV-CU360C
WJ-FS616C  ← WV-CU360C
WJ-FS616C  → WV-CU360C
WJ-FS616C  → WV-CU360C
–
1
61
6
No.No.
11
22
33
44
55
66
Name
GND
TX(B)
TX(A)
RX(B)
RX(A)
GND
Controller endTX (B) 
TX (A)
RX (A)
RX (B) 
						

							45
Controller Number Setting 
Set this switch always to 1 when using the System
Controller in a system including a Multiplexer WJ-
FS616/FS616C. 
Switch Setting Procedures
1. Remove the DC plug from the rear of the controller.
2. Set the MODE switch referring to the table.
• The bit switches #1 to #3 should be set to positions that
match the version of the Multiplexer installed in the sys-
tem.
• Bit 5 opens or terminates the communication chain. The
switch should be set to OFF when the controller is locat-
ed in an intermediate position of the chain.
• Bit 6 specifies either Operator or Administrator as the
operation mode.  Set to Administrator when setting up
the controller.
• Bits 4, 7 and 8 are reserved.
3. Set the CONTROLLER NO. switch to 1.
4. Connect the DC plug to the controller.
Unit Version
The unit ID is defined by the upper 3 bits depending on the
software version installed in the unit.
•WJ-FS616
•WJ-FS616C
MODE
123456 78
OFF
ON
MODE
123456 78
OFF
ON
0987654321
CONTROLLER No. 
						

							46
SETUP PROCEDURES (For WJ-FS616/FS616C)
To display the setup menus for the WV-CU360C System Controller on the LED display, set the MODE switch and power up the
controller as described below.
Prior to Setup
Do the following before entering the setup mode.
1. Confirm that all necessary connections and switch set-
tings are complete.
2. With the power turned off, move bit #6 of the MODE
switch on the rear to ON (administrator) position.
3. Supply power to the controller.
4. Turn on the power of cameras and other system units.
5. The LCD displays [SEtUP]. The controller is ready to
enter the setup mode.
When setup is completed, restore the switch to its original
position.
1. With the power turned off, move bit #6 of the MODE
switch on the rear to OFF (operator) position.
2. Supply power to the controller.
Buttons and Controls used for Setup
The following buttons and joystick operations are used for
setup.
0
9Numeric buttons: To select a parameter
CAM/SET button: To execute modes and
parameters
To enter a submenu
UNIT/ESC button: To return to the previous
menu
CAM
SET
UNIT
ESC
DOWN LRUP
LR
UP
DOWNR
UP
DOWN LR
Up: To select a setup menu
Down: To select a setup menu
Left: To decrease the parameter
Right: To increase the parameter 
HOME/-
AUX 1
AUTO/+
AUX 2
or
or 
						

							47
Controller Setup 
Set up the baud rate and parity check mode for the controller while observing the LED on the front panel.
Administrator Authorization
1. Press the CAM/SET button while [SEtUP] is displayed.
The [- - - - -] prompt appears.
2. Enter a password with the numeric buttons, then press
the CAM/SET button.
The default setting is [12345].
3. If the password entered is valid, [SPEED] appears.  If
password entry failed, the menu returns to [SEtUP].
Baud Rate
In this menu, the communication speed (bps: bits per sec-
ond) is selected.  The communication speed should match
that of the WJ-FS616/FS616C.
1. Display [SPEED] and press the CAM/SET button twice.
2. Select a parameter entering a bracket-enclosed num-
ber, e.g., (3), moving the joystick to right and left, or
pressing the [+] and [–] buttons.
The default setting is 9 600 bps.
(1) 2 400:2 400 bps
(2) 4 800:4 800 bps
(3) 9 600:9 600 bps
(4) 19 200:19 200 bpsNote:Selecting a slower rate (e.g., 2 400 bps) will delay
the response time (e.g., the time until an activated
alarm is reset).
3. Press the CAM/SETbutton to validate the selection.
4. Press the ESCbutton to go back to the previous menu.
Parity
In this menu the parity check mode is selected.
1. Display [PrtY] and press the CAM/SETbutton twice.
2. Select a parameter with the joystick.
The default setting is None.
n:None
E:Even parity
3. Press the CAM/SETbutton to validate the selection. Menu 
Selection
Move Joystick 
UP and down 
to selectSetup Menus
Parameter Selection (default*)
LED Display
blinking
Setup
Administrator
Password
Prompt
Speed
ParityInitial
Display
Authorization
Baud Rate
(bps)Press
twice
Parity Check
CAM
SET
CAM
SET
MON
ESC
LED prompts you to enter pass-
word
Enter a 5-digit password, 
press                 (12345*)
(1) 2 400  (2) 4 800  (3) 9 600*
(4) 19 200
(1) None*   (2) Even Reading Function
OK No
DOWN LRUP
LR
CAM
SET 
						

							48
4. Press the ESCbutton to go back to the previous menu.
Note:The baud rate and parity check mode of both the
WJ-FS616/FS616C and the controller must be the
same, otherwise data communications will not function.
To confirm the WJ-FS616/FS616C setup, open the COM
PORT SETUP window to check the DATA port column
parameters. Refer to Multiplexer Setup for operation.
             COM PORT SETUP
               RS-232C DATA    RS-485
    DELAY       OFF    OFF     OFF  
    BAUD RATE   9600   9600    19200
    WAIT TIME   OFF    OFF     OFF
    DATA BIT    7      8       8
    PARITY      ODD    NONE    NONE
    STOP BIT    1      1       1
    XON/XOFF    -      OFF     OFF
    FULL/HALF   -      -       FULL
    
    
    
						

							49
OPERATING PROCEDURES (For WJ-FS616/FS616C System)
Camera Selection
One of the cameras connected to the system unit is select-
ed.
1. Enter a camera number using the numeric buttons.
The number appears on the LED display.
2. Press the CAM/SETbutton.
Note:[--] appears in the camera section of the LED dis-
play when an alarm is activated, when the multi-
screen is displayed, or when sequence mode is
run.
The following functions of the camera are controlled.
• Pan/tilt
• Focus
• Zoom
• Iris
• Defroster ON/OFF (camera housing)
• Wiper ON/OFF (camera housing)
• Preset Position (Combination Camera)
• Home position (Combination Camera)
• Auto pan (Combination Camera)
The following additional functions can be controlled when
using the WV-CS854 or later camera models.
• Switching between color and B/W picture
(Combination Camera)
• Patrol Learn function (Combination Camera)
• Camera functions (Combination Camera)
Camera Control
Cameras and their peripherals are controlled from the WV-
CU360C as follows. Some of the descriptions may not be
applicable if they refer to devices not equipped in your sys-
tem.
Pan/Tilt Control
Proceed as follows to control an ordinary camera mounted
on a pan/tilt head or a combination camera in manual or
automatic panning mode.
1. Move the pan/tilt head in the desired direction with the
joystick controller.
2. Press the AUTO/+button to activate a preset auto pan-
ning.
AUX Control
This allows you to control an auxiliary device such as a
buzzer or lamp connected to the Receiver or combination
camera.
8Auxiliary 1/2
1. Press the ALTbutton to turn on the ALTindicator .
2. Press the AUX 1or AUX 2button to operate or cancel
the auxiliary function for the selected camera. Note: For common operations to the controller and the WJ-FS616/FS616C, please refer to the manual included with the
WJ-FS616/FS616C. The following pages describe only operations different from the WJ-FS616/FS616C.
UNITCAM
ESC SET
CAM
SET
UP
LR
DOWN
ALTAUTO/+
HOME/-
AUX 2
AUX 1 
						

							50
Note:Auxiliary control may be ignored while zooming,
focusing or panning/tilting is in operation. 
Alarm Operation
When the WV-CU360C receives an alarm signal from the
WJ-FS616/FS616C, the alarm indicator blinks. The alarm
indicator changes from blinking to steady light when the
alarm is automatically reset. The camera number appears
in the camera section of the LED display.
Alarm Reset
1. Press the ALM RESETbutton while the ALTindicator is
not lit. An activated alarm is reset and the alarm indica-
tor on the controller goes off.
2. To reset all alarms issued by the multiplexers connect-
ed in a daisy chain, press the ALTbutton, then press
theALM RESETbuttons.
Alarm Suspension
1. Press the ALM SUSPENDbutton for more than 2 sec-
onds to suspend the alarm. The ALM SUSPENDindi-
cator lights up.
2. Press the ALM RESETbutton to reset alarm suspen-
sion. The ALM SUSPENDindicator goes off.
VTR (VCR) Control
You can operate a VTR (VCR) connected to the Video
Multiplexer from the controller using the buttons listed
below with the ALT indicator lit.
Function
Rewind
Pause
Fast Forward
Reverse Play
Stop
Playback
T/L (time-
lapse) Mode
Down
Up
RecordingLogoNote
e.g., change from 72H mode
to 24H mode
e.g., change from 24H mode
to 72H mode
ALM RESET
ALL RESET
ALM RESET
ALL RESET
ALM SUSPEND 
						

							51
Camera Setup
The cameras connected to the WJ-FS616/FS616C are set
up from the controller.
Note: Make sure that the multiplexer and the controller
are set to identical communication parameters.
General Setup
1. Select a camera pressing the numeric buttons, then
press the CAM/SET button.
2. Press the CAMERA SET ONbutton. The ON indicator
is lit while the CAMERA SET UP MENU is displayed on
the monitor.
3. Select a setup item by moving the joystick up and
down. Select a parameter by moving the joystick to the
right or left, then press the CAM/SETbutton to validate
the selection or to enter a submenu. 
4. Press the UNIT/ESCbutton to execute the selection
and to return the menu to a higher layer.
5. Press the SEQUENCEbutton to enter the SPECIAL
menu.6. Press the VTR/CAMbutton to reset all functions to the
defaults, or press the SEQUENCEbutton to reset a
selected function.
7. Press the CAMERA SET OFFbutton to close the cam-
era setup menu.
Shortcut for Preset Position Setup
A shortcut can be created for setting a camera position
without going through the whole presetting process.
Shortcuts are applicable only to cameras having the preset-
ting function.
1. Open the PRESET menu of the camera.
2. Press the ALTbutton while the position setting menu is
displayed.
3. Move the camera with the joystick to the position you
wish to preset.
4. Adjust the picture with the IRIS, FOCUSand ZOOM
buttons.
5. Press the ALTbutton again. The preset conditions are
registered, and the joystick function reverts to moving
the cursor.
CAMERA SET
ON OFF
T/L MODE
UP
R
DOWN
CAM
SET
L
UNIT
ESC
SEQUENCE
VTR
CAM
CAMERA SET
ON OFF
T/L MODE