ProForm Endurance 520 E Manual

USER’S MANUAL
Serial 
Number 
Decal
    CAUTION
Read all precautions and 
instructions in this manual before 
using this equipment. Keep this 
manual for future reference.
Model No. PFEVEL69716.0
Serial No.                                  
Write the serial number in the space 
above for reference.
www.iconeurope.com
CUSTOMER SERVICE
UNITED KINGDOM
Call: 0330 123 1045
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: [email protected]
Write: 
ICON Health & Fitness, Ltd.
Unit 1D, The...

2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning 
decal(s). If a decal is missing or illegible, see 
the front cover of this manual and request a 
free replacement decal. Apply the decal in the 
location shown. Note: The decal(s) may not be 
shown at actual size.
WARNING DECAL PLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS...

3
    WARNING: To reduce the risk of serious injury, read all important precautions and 
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON 
assumes no responsibility for personal injury or property damage sustained by or through the 
use of this product.
1. It is the responsibility of the owner to ensure 
that all users of the elliptical are adequately 
informed of all precautions.
2. Before beginning any exercise program, 
consult your physician. This is...

4
Thank you for selecting the revolutionary PROFORM® 
ENDURANCE 520 E elliptical. The ENDURANCE 520 
E elliptical provides an impressive selection of features 
designed to make your workouts at home more effec-
tive and enjoyable.
For your benefit, read this manual carefully before 
you use the elliptical. If you have questions after 
reading this manual, please see the front cover of this 
manual. To help us assist you, note the product model 
number and serial number before contacting us. The 
model...

5
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each 
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the 
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it 
has been preassembled. Extra parts may be included.
M8 x 13mm 
Screw (82)–6
M10 x 25mm 
Screw (92)–4M10 x 122mm Screw  (104)–4
M8 Locknut (102)–4...

6
2. With the help of a second person, place some of 
the packing materials (not shown) under the rear 
of the Frame (1). Have the second person hold 
the Frame to prevent it from tipping while you 
complete this step.
 Attach the Rear Stabilizer (2) to the Frame (1) 
with two M10 x 122mm Screws (104) and two 
M10 Split Washers (105).
 Then, remove the packing materials from under 
the rear of the Frame (1).
2
12
104105
• Assembly requires two persons.
• Place all parts in a cleared area and remove the...

7
3
2
106
15
3. Press the Cover Mounts (106) on the underside 
of the Rear Stabilizer Cover (15) into the Rear 
Stabilizer (2). 
44. With the help of a second person, place some 
of the packing materials (not shown) under the 
front of the Frame (1). Have the second per-
son hold the Frame to prevent it from tipping 
while you complete this step.
 Attach the Front Stabilizer (6) to the Frame (1)
with two M10 x 122mm Screws (104) and two 
M10 Split Washers (105).
 Then, remove the packing materials from...

8
55. Orient the Upright (4) as shown. Have a second 
person hold the Upright near the Frame (1).
 See the inset drawing. Locate the wire tie in the 
lower end of the Upright (4). Tie the wire tie to 
the Main Wire (110). Then, pull the upper end of 
the wire tie until the Main Wire is routed through 
the Upright.
 Tip: To prevent the Main Wire (110) from fall-
ing into the Upright (4), secure the Main Wire 
with the wire tie.
1
4
11 0
Wire 
Tie
Wire 
Tie
11 0
66. Tip: Avoid pinching the Main Wire (110)....

9
77. Using a plastic bag to keep your fingers clean, 
apply some of the included grease to the Pivot 
Axle (35) and to two 16mm Wave Washers (54).
 Insert the Pivot Axle (35) through the Upright (4) 
and center it. Tip: It may be helpful to use a 
rubber mallet.
 Next, identify the Right Upper Body Leg (60) and 
orient it as shown.
 Slide a 16mm Wave Washer (54) and the Right 
Upper Body Leg (60) onto the right side of the 
Pivot Axle  (35).
 Repeat these actions for the Left Upper Body 
Leg (46)....

10
9
7
4
63
11 0
9. Untie and discard the wire tie on the Main 
Wire (110).
 While a second person holds the Console (7) 
near the Upright (4), connect the wires on the 
Console to the Main Wire (110) and to the Pulse 
Sensor Wires (63). 
 Insert the excess wire into the Upright (4) or into 
the Console (7). 
10
Avoid pinching 
the wires
7
10. Tip: Avoid pinching the wires. Attach 
the Console (7) to the Upright (4) with four 
M4 x 16mm Screws (101); start all the Screws, 
and then tighten them.
101
101
4