Ricoh Mp C2003 User Guide

							MessagesCausesSolutions"Unable to access the
specified memory storage
device."• An error occurred when the machine
accessed the memory
storage device or a file
stored on the memory
storage device.
• An error occurred when the user used the
Direct printing function to print from a memory
storage device.Save the file to a different memory storage device, and then try to print
again.
Messages Printed on the Error Logs or Reports When Using the Printer Function
This section describes likely causes of and possible solutions for the error messages that are printed on
the error logs or reports.
When print jobs are canceled
MessagesCausesSolutions"91: Error"Printing was canceled by the
auto job cancel function due
to a command error.Check that the data is valid."An error occurred while
processing an Unauthorized
Copy Prevention job. The
job was cancelled."You tried to store a file in the
Document Server when the
[Unauthorized Copy
Prevention] was specified.On the printer driver, select a job type
other than [Document Server] in "Job
Type:" or deselect [Unauthorized Copy
Prevention]."An error occurred while
processing an Unauthorized
Copy Prevention job. The
job was cancelled."The [Enter User Text:] field
on the [Unauthorized Copy
Prevention for Pattern
Details] screen is blank.On the printer driver's [Detailed
Settings] tab, click [Effects] in "Menu:".
Select [Unauthorized Copy
Prevention], and then click [Details] to
display [Unauthorized Copy
Prevention for Pattern Details]. Enter
text in [Enter User Text:].Messages Displayed When Using the Printer Function
199  
						

							MessagesCausesSolutions"An error occurred while
processing an Unauthorized
Copy Prevention job. The
job was cancelled."The resolution is set to a
value less than 600 dpi
when [Unauthorized Copy
Prevention] is specified.On the printer driver, set the resolution
to 600 dpi or higher, or deselect
[Unauthorized Copy Prevention]."Collate has been
cancelled."Collate was canceled.Turn off the power, and then back on
again. If the message appears again,
contact your service representative."Exceeded the maximum unit
count for Print Volume Use.
The job has been
cancelled."The number of pages the
user is permitted to print has
been exceeded.For details about print volume use
limitation, see Security Guide."Receiving data failed."Data reception was aborted.Resend the data."Sending data failed."The machine received a
command to stop
transmission from the printer
driver.Check if the computer is working
correctly."The selected paper size is
not supported. This job has
been cancelled."Job reset is automatically
performed if the specified
paper size is incorrect.Specify the correct paper size, and
then print the file again."The selected paper type is
not supported. This job has
been cancelled."Job reset is automatically
performed if the specified
paper type is incorrect.Specify the correct paper type, and
then print the file again.
When there is a problem with the print settings
MessagesCausesSolutions"Classification Code is
incorrect."The classification code has
not been entered, or the
classification code has been
entered incorrectly.Enter the correct classification code.10. Troubleshooting
200  
						

							MessagesCausesSolutions"Classification Code is
incorrect."The classification code is not
supported with the printer
driver.Select [Optional] for classification
code. For details about how to specify
classification code settings, see
"Configuring Classification Codes",
Print."Duplex has been
cancelled."Duplex printing was
canceled.• Select an appropriate paper size for the duplex function. For details
about paper, see "Specifications
for the Main Unit", Maintenance
and Specifications.
• Change the setting for "Apply Duplex" in [System Settings] to
enable duplex printing for the
paper tray. For details about
setting "Apply Duplex", see "Tray
Paper Settings", Connecting the
Machine/ System Settings."Exceeded max. pages.
Collate is incomplete."The number of pages
exceeds the maximum
number of sheets that you
can use Collate with.Reduce the number of pages to print."Output tray has been
changed."The output tray was
changed because the paper
size of the specified output
tray is limited.Specify the proper output tray."Print overrun."Images were discarded
while printing.PCL 6
Select a lower resolution on the
printer driver. For details about
how to change the resolution setting, see the printer driver Help.
PostScript 3
Select a lower resolution on the
printer driver. For details about
how to change the resolution setting, see the printer driver Help.Messages Displayed When Using the Printer Function
201  
						

							MessagesCausesSolutions"Punch has been cancelled."Punch printing was
canceled.Check the paper orientation, print
orientation, and then punch position.
Certain settings can produce print
results that might not be as expected."Staple has been cancelled."Stapling printing was
canceled.Check the paper orientation, paper
quantity, print orientation, and staple
position. Certain settings can produce
print results that might not be as
expected.
When documents cannot be stored in the Document Server
MessagesCausesSolutions"Cannot store data of this
size."The paper size exceeded
the capacity of the
Document Server.Reduce the paper size of the file that
you want to send to a size that the
Document Server can store. Custom
size files can be sent but not stored
afterward."Document Server is not
available to use. Cannot
store."You cannot use the
Document Server function.For details about using Document
Server function, contact your
administrator.
For details about how to set
permissions, see Security Guide."Exceeded max. capacity of
Document Server. Cannot
store."The hard disk became full
after a file was stored.Delete some of the files stored in the
Document Server or reduce the size
that you want to send."Exceeded max. number of
files of Document Server.
Cannot store."The maximum file capacity
of the Document Server was
exceeded.Delete some of the files stored in the
Document Server.10. Troubleshooting
202  
						

							MessagesCausesSolutions"Exceeded max. number of
files. (Auto)"While using the error job
store function to store
Normal Print jobs as Hold
Print files, the maximum file
capacity for file storage or
Hold Print file management
(automatic) was exceeded.Delete Hold Print files (automatic) or
unneeded files stored in the machine."Exceeded max. number of
pages of Document Server.
Cannot store."The maximum page
capacity of the Document
Server was exceeded.Delete some of the files stored in the
Document Server or reduce the number
of pages that you want to send."Exceeded max. number of
pages. (Auto)"While using the error job
store function to store
Normal Print jobs as Hold
Print files, the maximum
page capacity was
exceeded.Delete unneeded files stored in the
machine.
Reduce the number of pages to print."The print job has been
cancelled because capture
file(s) could not be stored:
Exceeded max. memory."The hard disk became full
after a file was stored.Delete the files stored in the Document
Server or reduce the file size to be sent."The print job has been
cancelled because capture
file(s) could not be stored:
Exceeded max. number of
files."The maximum file capacity
of the Document Server was
exceeded.Delete the files stored in the Document
Server."The print job has been
cancelled because capture
file(s) could not be stored:
Exceeded max. number of
pages per file."The maximum page
capacity of the Document
Server was exceeded.Delete some of the files stored in the
Document Server or reduce the number
of pages that you want to send."The specified folder in
Document Server is locked.
Cannot store."The specified folder is
locked.Unlock the folder or specify another
folder number that can be used. For
details about locked folders, see
Security Guide.Messages Displayed When Using the Printer Function
203  
						

							When there is not enough free hard disk spaceMessagesCausesSolutions"HDD is full."When printing with the
PostScript 3 printer driver,
the hard disk capacity for
fonts and forms has been
exceeded.Delete unneeded forms or fonts
registered in the machine."HDD is full."The hard disk became full
while printing a Sample
Print, Locked Print, Hold
Print, or Stored Print file.Delete unneeded files stored in the
machine.
Alternatively, reduce the data size of
the Sample Print, Locked Print, Hold
Print, or Stored Print file."HDD is full. (Auto)"The hard disk became full
while using the error job
store function to store
Normal Print jobs as Hold
Print files.Delete unneeded files stored in the
machine.
Alternatively, reduce the data size of
the Temporary Print file and/or the
Stored Print file.
When there is not enough memory
MessagesCausesSolutions"84: Error"There is no work area
available for image
processing.Decrease the number of files sent to the
machine."92: Error"Printing was canceled
because [Job Reset] or the
[Stop] key was selected on
the machine's control panel.Perform the print operation again if
necessary.
When there is a problem with a parameter
MessagesCausesSolutions"86: Error"Parameters of the control
code are invalid.Check the print settings.10. Troubleshooting
204  
						

							When the user lacks privileges to perform an operationMessagesCausesSolutions"No response from the
server. Authentication has
failed."A timeout occurred while
connecting to the server for
LDAP authentication or
Windows Authentication.Check the status of the server."Printing privileges have not
been set for this document."The PDF document you have
tried to print has no
privileges to print.Contact the owner of the document."You do not have a privilege
to use this function. This job
has been cancelled."The entered login user name
or login password is not
correct.Check that the user name and
password are correct."You do not have a privilege
to use this function. This job
has been cancelled."The logged in user is not
allowed to use the selected
function.For details about how to set
permissions, see Security Guide."You do not have a privilege
to use this function. This
operation has been
cancelled."The logged in user does not
have the privileges to
register programs or change
the paper tray settings.For details about how to set
permissions, see Security Guide.
When a user cannot be registered
MessagesCausesSolutions"Auto-registration of user
information has failed."Automatic registration of
information for LDAP
Authentication or Windows
Authentication failed
because the Address Book is
full.For details about automatic registration
of user information, see Security
Guide.Messages Displayed When Using the Printer Function
205  
						

							MessagesCausesSolutions"Information for user
authentication is already
registered for another user."The user name for LDAP or
Integration Server
authentication was already
registered in a different
server with a different ID,
and a duplication of the user
name occurred due to a
switching of domains
(servers), etc..For details about user authentication,
see Security Guide.
When other errors occur
MessagesCausesSolutions"85: Error"The specified graphics
library is unavailable.Check that the data is valid."98: Error"The machine could not
access Hard disk correctly.Turn off the power, and then back on
again. If the message appears
frequently, contact your service
representative."99: Error"This data cannot be printed.
The specified data is either
corrupt or it cannot be
printed from a memory
storage device using the
Direct printing function.Check that the data is valid. For details
about the kinds of data that can be
printed from a memory storage device
using the Direct printing function, see
"Direct Printing from a Memory
Storage Device", Print."Command Error"An RPCS command error
occurred.Check using the following procedure:
• Check if the communication between the computer and the
machine is working correctly.
• Check if the correct printer driver is being used.
• Check if the machine's memory size is set correctly in the printer
driver.
• Check that the printer driver is the most up-to-date version available.10. Troubleshooting
206  
						

							MessagesCausesSolutions"Compressed Data Error."The printer detected corrupt
compressed data.• Check the connection between the computer and the printer.
• Check that the program you used to compress the data is
functioning correctly."Data storage error."You tried to print a Sample
Print, Locked Print, Hold
Print, or Stored Print file, or
to store a file in the
Document Server when the
hard disk was
malfunctioning.Contact your service representative."Error has occurred."A syntax error, etc.,
occurred.Check that the PDF file is valid."Exceeded max. number of
files to print for temporary /
stored jobs."While printing a Sample
Print, Locked Print, Hold
Print, or Stored Print file, the
maximum file capacity was
exceeded.Delete unneeded files stored in the
machine."Exceeded max. number of
pages to print for
temporary / stored jobs."While printing a Sample
Print, Locked Print, Hold
Print, or Stored Print file, the
maximum page capacity
was exceeded.Delete unneeded files stored in the
machine.
Reduce the number of pages to print."Failed to obtain file system."PDF direct printing could not
be performed because the
file system could not be
obtained.Turn off the power, and then back on
again. If the message appears again,
contact your service representative."File system is full."PDF file does not print out
because the capacity of the
file system is full.Delete all unnecessary files from the
hard disk, or decrease the file size sent
to the machine.Messages Displayed When Using the Printer Function
207  
						

							MessagesCausesSolutions"I/O buffer overflow."An input buffer overflow
occurred.• In [Printer Features], under [Host Interface], select [I/O Buffer],
and then set the maximum buffer
size to a larger value.
• Reduce the number of files being sent to the machine."Insufficient Memory"A memory allocation error
occurred.PCL 6
On the printer driver's [Detailed
Settings] tab, click [Print Quality]
in "Menu:", and then select
[Raster] in the "Vector/Raster:"
list. In some cases, it will take a
long time to complete a print job."Memory Retrieval Error"A memory allocation error
occurred.Turn off the power, and then back on
again. If the message appears again,
replace the RAM. For details about
replacing the RAM, contact your
service representative.
If printing does not start, contact your service representative.
• The contents of errors may be printed on the Configuration Page. Check the Configuration Page in conjunction with the error log. For details about how to print the Configuration Page, see "List / Test
Print", Print.
10. Troubleshooting
208