Samsung C460 User Guide

							1512.  Using a Network-Connected Machine
Installing driver over the network
 
• Some features and optional goods may not be available depending on model or country (see "Features by model" on page 7).
• The machine that does not support th e network interface, it will not be 
able to use this feature (see "Rear view" on page 22).
• You can install the printer driver  and software when you insert the 
software CD into your CD-ROM drive.
For windows, select the printe r driver and software in the Select 
Software to Install  window.
 
6 
Windows
 
The firewall software might be blocking network communication. Before 
connecting the device to the networ k, disable the computer’s firewall.
 
1Make sure that the machine is conne cted to the network and powered 
on. Also, your machine’s IP address sh ould have been set (see "Setting IP 
address" on page 148).
2 Insert the supplied software CD into your CD-ROM drive.
3 Review and accept the installation  agreements in the installation 
window. Then, click  Next.
4 Select  Network Connection  on the Printer Connection Type  screen.
5 Follow the instructions in the installation window.
Silent installation Mode
Silent installation mode is  an installation method that  does not require any user 
intervention. Once you start  the installation, the machine driver and software 
are automatically installed on  you computer. You can start the silent installation 
by typing  /s or  /S in the command window.
Command-line Parameters
Following table shows commands that  can be used in the command window.
 
Following command-line are effective and operated when command is 
used with /s  or /S. But /h , /H  or  /? are exceptional commands that can be 
operated solely.
 
Command- lineDefinitionDescription
/s or
/S Starts silent installation.  Installs machine drivers 
without prompting any UIs 
or user intervention. 
						

							Installing driver over the network
1522.  Using a Network-Connected Machine
/p”” or
/P””Specifies printer port.
 
Network Port will be 
created by use of 
Standard TCP/IP 
Port monitor. For 
local port, this port 
must exist on 
system before 
being specified by 
command.
 
Printer port name can be 
specified as IP address, 
hostname, USB local port 
name or IEEE1284 port 
name.
For example:
•  /p”xxx.xxx.xxx.xxx” in 
where, “xxx.xxx.xxx.xxx” 
means IP address for 
network printer. /
p”USB001”, /P”LPT1:”, /
p”hostname”
/a”” or
/A”” Specifies destination path 
for installation.
 
The destination 
path should be a 
fully qualified path.
 
Since machine drivers 
should be installed on the 
OS specific location, this 
command applies to only 
application software.
/n”” 
or
/N””Specifies printer name. 
Printer instance shall be 
created as specified printer 
name. With this parameter, you 
can add printer instances as 
you wish.
Command- lineDefinitionDescription
/nd or
/ND
Commands not to set the 
installed driver as a default 
machine driver. It indicates installed 
machine driver will not be 
the default machine driver 
on your system if there are 
one or more printer drivers 
installed. If there is no 
installed machine driver on 
your system, then this 
option won’t be applied 
because Windows OS will 
set installed printer driver as 
a default machine driver.
/x or
/X
Uses existing machine 
driver files to create printer 
instance if it is already 
installed. This command provides a 
way to install a printer 
instance that uses installed 
printer driver files without 
installing an additional 
driver.
/up”” or
/UP””Removes only specified 
printer instance and not the 
driver files.
This command provides a 
way to remove only 
specified printer instance 
from your system without 
effecting other printer 
drivers. It will not remove 
printer driver files from your 
system.
Command- lineDefinitionDescription 
						

							Installing driver over the network
1532.  Using a Network-Connected Machine
7 
Mac
1Make sure that the machine is connected to your network and powered 
on.
2 Insert the supplied software CD  into your CD-ROM drive.
3 Double-click the CD-ROM icon that appears on your Mac desktop.
• For Mac OS X 10.8, double-cli ck the CD-ROM that appears on Finder.
4 Double-click the MAC_Installer folder >  Installer OS X icon.
5  Click Continue .
6 Read the license agreement and click  Continue.
7 Click Agree  to agree to the  license agreement.
8 Click Install. All components necessary for  machine operations will be 
installed.
If you click  Customize , you can choose individual components to install.
/d or
/D Uninstalls all device drivers 
and applications from your 
system. This command will remove 
all installed device drivers 
and application software 
from your system.
/v”” or
/V””
Shares installed machine 
and add other available 
platform drivers for Point & 
Print. It will install all supported 
Windows OS platform’s 
machine drivers to system 
and share it with specified 
 for point and 
print.
/o or 
/O
Opens 
Printers and Faxes  
folder after installation. This command will open 
Printers and Faxes
 folder 
after the silent installation.
/h, /H or /? Shows Command-line Usage.
Command- lineDefinitionDescription 
						

							Installing driver over the network
1542.  Using a Network-Connected Machine
9 Enter the password and click OK.
10 Select Network Connected Printe r(Wired or Wireless) on the  Printer 
Connection Type  and click Continue.
11 Click Add Printer  button to select your printer  and add it to your printer 
list.
12 Click  IP and select  HP Jetdirect - Socket  in Protocol .
13 Enter the machine’s  IP address in the Address input field.
14 Enter the queue name in the  Queue input field. If you cannot determine 
the queue name for your  machine server, try using the default queue 
first.
15 If Auto Select does not  work properly, choose Select Printer Software  
and your machine name in  Print Using.
16 Click Add.
17 After the installation  is finished, click Close.
 
To install the fax driver: 
a  Open the  Applications  folder > Samsung  > Fax Queue Creator .
b  Your machine appears on the  Printer List.
c  Select machine to use and Click  Create button.
 
8 
Linux
You need to download Linux software packages from the Samsung website to 
install the printer software  (http://www.samsung.com > find your product > 
Support or Downloads).
Install the Linux driver and add network printer
1Make sure that the machine is conne cted to your network and powered 
on. Also, your machine’s IP ad dress should have been set. 
2 Download the Unified Linux Driver  package from the Samsung website.
3 Extract the UnifiedLinuxDriver.tar.gz file and open the new directory.
4 Double-click the cdroot > autorun  
5 The Samsung installer window opens. Click  Next.
6 The add printer wizard  window opens. Click Next.
7 Select network printer and click  Search button.
8 The machine’s IP address and mod el name appears on list field.
9 Select your machine and click Next. 
						

							Installing driver over the network
1552.  Using a Network-Connected Machine
10 Input the printer description and Next.
11 After the machine is added, click  Finish.
12 When installation is done, click  Finish.
Add a network printer
1Double-click the  Unified Driver Configurator .
2 Click Add Printer.
3 The Add printer wizard  window opens. Click  Next.
4 Select  Network printer  and click the Search button.
5 The printer’s IP address and mod el name appears on list field.
6 Select your machine and click Next.
7 Enter the printer description and click  Next.
8 After the machine is added, click  Finish. 
						

							1562.  Using a Network-Connected Machine
IPv6 configuration
 
IPv6 is supported properly only in Windows Vista or higher.
 
 
• Some features and optional goods may not be available depending on 
model or country (see "Features by model" on page 7  or "Menu 
overview" on page 31).
• If the IPv6 network seems to not be working, set all the network setting  to the factory defaults and try again using  Clear Setting.
 
The machine supports the fo llowing IPv6 addresses for network printing and 
managements.
• Link-local Address : Self-configured local IPv6 address (Address starts with 
FE80).
• Stateless Address : Automatically configured  IPv6 address by a network 
router.
• Stateful Address : IPv6 address configur ed by a DHCPv6 server.
• Manual Address : Manually configured IPv6 address by a user.
In the IPv6 network environment, foll ow the next procedure to use the IPv6 
address.
9 
From the control panel
Activating IPv6
1Press the   ( Menu) button on the control panel.
2 Press Network  > TCP/IP (IPv6)  > IPv6 Activate .
3 Select On and press  OK.
4 Turn the machine off and turn it on again.
 
When you install the printer dr iver, do not configure both IPv4  and 
IPv6. We recommend to configure either IPv4 or IPv6  ( see  "Installing 
driver over the network" on page 151) .
 
DHCPv6 address configuration
If you have a DHCPv6 server on your network, you can set one  of the following 
options for default dyna mic host configuration.
1Press the   (Menu) button on the control panel.
2 Press Network  > TCP/IP (IPv6)  > DHCPv6 Config . 
						

							IPv6 configuration
1572.  Using a Network-Connected Machine
3 Press OK to select the requ ired value you want.
• DHCPv6 Addr. : Always use DHCPv6 rega rdless of router request.
• DHCPv6 Off : Never use DHCP v6 regardless of router request.
• Router : Use DHCPv6 only when  requested by a router.
10 
From the SyncThru™ Web Service
Activating IPv6
1Access a web browser, such as In ternet Explorer, from Windows. Enter 
the machine IP address (http://xxx.xxx.xxx.xxx) in the  address field and 
press the Enter key or click  Go.
2 If it’s your first  time logging into  SyncThru™ Web Service  you need to 
log-in as an administrat or. Type in the below default ID and password. 
We recommend you to change the  default password for security 
reasons.
• ID: admin
• Password: sec00000 
3 When the  SyncThru™ Web Service  window opens, move the mouse 
cursor over the  Settings of the top menu  bar and then click  Network 
Settings .
4 Click TCP/IPv6 on the left pane of the website.
5 Check the  IPv6 Protocol  check box to activate IPv6.
6 Click the Apply  button.
7 Turn the machine off and turn it on again.
 
• You can also set the DHCPv6.
• To manually set the IPv6 address:
Check the  Manual Address  check box. Then, the  Address/Prefix text 
box is activated. Enter the rest of the address 
(e.g.,:3FFE:10:88:194:: AAAA. “A” is the hexadecimal 0 through 9, A 
through F).
 
IPv6 address configuration
1Start a web browser, such as Inter net Explorer, that supports IPv6 
addressing as a URL.
2 Select one of the  IPv6 addresses (Link-local Address , Stateless 
Address , Stateful Address , Manual Address ) from Network 
Configuration Report  (see "Printing a network configuration report" on 
page 148).
• Link-local Address : Self-configured loca l IPv6 address (Address 
starts with FE80).
• Stateless Address : Automatically configure d IPv6 address by a 
network router. 
						

							IPv6 configuration
1582.  Using a Network-Connected Machine
•Stateful Address : IPv6 address configur ed by a DHCPv6 server.
• Manual Address : Manually configured IP v6 address by a user.
3 Enter the IPv6 addresses  (e.g.,: http://[FE80::215:99FF:FE66:7701]).
 
Address must be enclosed in '[ ]' brackets.
  
						

							1592.  Using a Network-Connected Machine
Wireless network setup
 
• Make sure your machine supports wireless networking. Wireless networking may not be available depending on the model (see "Features 
by model" on page 7).
• If the IPv6 network seems to not be working, set all the network settings  to the factory defaults and try again using  Clear Setting.
 
11 
Getting started
Understanding your network type
Typically, you can only have one connect ion between your computer and the 
machine at a time.
Wireless network name and network password
Wireless networks require higher security, so  when an access point is first set up, 
a network name (SSID), th e type of security used, an d a Network Password are 
created for the network. Ask your network  administrator about this information 
before proceeding with the machine installation.
Infrastructure mode
This is an environment generally used for homes and SOHOs 
(Small Office/ Home Office). This mode uses an access point to 
communicate with the wireless machine.
Ad hoc mode
This mode does not use an access point. The wireless 
computer and wireless machine communicate directly.  
						

							Wireless network setup
1602.  Using a Network-Connected Machine
12 
Introducing wireless set up methods
You can set wireless settings either from the machine or the computer. Choose the setting method from the below table.
 
Some wireless network installation types may not  be available depending on the model or country.
 
 
Set up methodConnecting methodDescription & Reference
With Access Point From the computer
Windows user, see "Access point via USB cable" on page 166.
Windows user, see "Access point without  a USB cable (recommended)" on page 170.
• Mac user, see "Access point via USB cable" on page 175.
• Mac user, see "Access point without a USB cable (recommended)" on page 178
See "Using a network cable" on page 183.
From the machine’s control 
panel • See "Machines with a display screen" on page 163.
• See "Machines without a disp
lay screen" on page 164.
See "Using the menu button" on page 166.