Home > Samsung > Printer > Samsung CLP 550N User Manual

Samsung CLP 550N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Samsung CLP 550N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1705 Samsung manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							SETUP GUIDE9
    English
    6Hold the handle on the imaging unit with the green roller 
    facing you. Align the imaging unit with the slots in your 
    printer so that the colors on both sides of the imaging unit 
    slide into the corresponding colors of the slots.
    CAUTION: Insert the imaging unit carefully so as not to scratch 
    and damage the surface of the green roller.
    7Slide the imaging unit down into the printer until it cannot 
    be pushed in any further and fold the handle down. 
    CAUTION: To prevent damage, do not expose the imaging unit to 
    light for more than a few minutes. Close the top and left cover 
    should the setup need to be halted for any reason.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: Keep the transfer belt level, do not turn the transfer belt 
    over otherwise looses toner may be spilled.
    13Slide the transfer belt down into the printer. Press it firmly 
    to make sure that it latches into place.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    CAUTION: Do not use sharp objects, such as a knife or scissors, 
    to open the toner cartridges packages. You could damage the 
    surface of the toner cartridges.
    17Holding both sides of the cartridges, gently roll them from 
    side to side to distribute the toner.
    18Place the toner cartridges on a flat surface as shown and 
    remove the paper covering on the toner cartridge by 
    removing the tape.
    NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
    and wash it in cold water. Hot water sets toner into fabric.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: When printing text at 5% coverage, you can expect a 
    toner cartridge life of about 7,000 pages for black and 5,000 pages 
    for color. 
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    TEUP: Connecting the printer to the USB port of the computer 
    requires a certified USB cable. You will need to buy a USB 2.0 
    compliant cable that is within 3m in length. 
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the USB printer cable into the connector on the back of 
    the printer. 
    3Connect the other end of the cable to the USB port on your 
    computer. 
    See the User’s Guide of your computer, if you need help.
    NOTE: To print using the USB interface, you must run Windows 
    98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
    To the USB port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    To the network 
    LAN connection
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: For Windows NT 4.0/2000/XP, the system administrator 
    should install the software. 
    All applications should be closed on your PC before beginning 
    installation. 
    1Place the CD-ROM in the CD-ROM drive. Installation will 
    start automatically.
    If the CD-ROM drive does not automatically run:
    Select Run from the Start menu, and type x:\Setup.exe 
    in the Open box (where x is the drive letter for the CD-ROM 
    drive), then click OK.
    NOTE: If the New Hardware Found window appears during the 
    installation procedure, click   in the upper right corner of the box, 
    or click Cancel. 
    ItemRequirements
    Operating systemWindows 95/98/Me/NT 4.0/2000/XP
    RAM95/98/Me 32 MB
    NT 4.0/2000 64 MB
    XP 128 MB
    Free disk space95/98/Me/NT 4.0/
    2000/XP300 MB
    Internet Explorer 5.0 or higher
    
    Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
    NOTE: If your printer is not connected to the computer, the 
    Connect Samsung CLP-550 Series window opens. After connecting 
    the printer, click Next.
    4Select the components you want to reinstall and click Next.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
    the View User’s Guide option automatically installs Adobe 
    Acrobat for you. After installing is complete, repeats step 1 and 2. 
    In Macintosh
    1Place the CD-ROM in the CD-ROM drive.
    2Double-click SAMSUNG_CLP on your Macintosh desktop.
    3Double-click User’s Guide folder.
    4Double-click User’s Guide.pdf(language). The Adobe 
    Acrobat programme opens and you can view the User’s 
    Guide.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE12
    14Firmly push the lock levers on each side towards the top 
    cover, as shown below, to lock the transfer belt into place.
    CAUTION: If you open the left cover for a few minutes, the 
    imaging unit can be exposed to light. This causes damage to the 
    imaging unit.
    15After making sure that the left cover is open, close the top 
    cover. Make sure that it is securely latched.
    CAUTION: Do not try to close the left cover with the top cover 
    open. This may cause damage to the printer.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE9
    English
    6Hold the handle on the imaging unit with the green roller 
    facing you. Align the imaging unit with the slots in your 
    printer so that the colors on both sides of the imaging unit 
    slide into the corresponding colors of the slots.
    CAUTION: Insert the imaging unit carefully so as not to scratch 
    and damage the surface of the green roller.
    7Slide the imaging unit down into the printer until it cannot 
    be pushed in any further and fold the handle down. 
    CAUTION: To prevent damage, do not expose the imaging unit to 
    light for more than a few minutes. Close the top and left cover 
    should the setup need to be halted for any reason.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: Keep the transfer belt level, do not turn the transfer belt 
    over otherwise looses toner may be spilled.
    13Slide the transfer belt down into the printer. Press it firmly 
    to make sure that it latches into place.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    CAUTION: Do not use sharp objects, such as a knife or scissors, 
    to open the toner cartridges packages. You could damage the 
    surface of the toner cartridges.
    17Holding both sides of the cartridges, gently roll them from 
    side to side to distribute the toner.
    18Place the toner cartridges on a flat surface as shown and 
    remove the paper covering on the toner cartridge by 
    removing the tape.
    NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
    and wash it in cold water. Hot water sets toner into fabric.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: When printing text at 5% coverage, you can expect a 
    toner cartridge life of about 7,000 pages for black and 5,000 pages 
    for color. 
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    TEUP: Connecting the printer to the USB port of the computer 
    requires a certified USB cable. You will need to buy a USB 2.0 
    compliant cable that is within 3m in length. 
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the USB printer cable into the connector on the back of 
    the printer. 
    3Connect the other end of the cable to the USB port on your 
    computer. 
    See the User’s Guide of your computer, if you need help.
    NOTE: To print using the USB interface, you must run Windows 
    98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
    To the USB port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    To the network 
    LAN connection
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: For Windows NT 4.0/2000/XP, the system administrator 
    should install the software. 
    All applications should be closed on your PC before beginning 
    installation. 
    1Place the CD-ROM in the CD-ROM drive. Installation will 
    start automatically.
    If the CD-ROM drive does not automatically run:
    Select Run from the Start menu, and type x:\Setup.exe 
    in the Open box (where x is the drive letter for the CD-ROM 
    drive), then click OK.
    NOTE: If the New Hardware Found window appears during the 
    installation procedure, click   in the upper right corner of the box, 
    or click Cancel. 
    ItemRequirements
    Operating systemWindows 95/98/Me/NT 4.0/2000/XP
    RAM95/98/Me 32 MB
    NT 4.0/2000 64 MB
    XP 128 MB
    Free disk space95/98/Me/NT 4.0/
    2000/XP300 MB
    Internet Explorer 5.0 or higher
    
    Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
    NOTE: If your printer is not connected to the computer, the 
    Connect Samsung CLP-550 Series window opens. After connecting 
    the printer, click Next.
    4Select the components you want to reinstall and click Next.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
    the View User’s Guide option automatically installs Adobe 
    Acrobat for you. After installing is complete, repeats step 1 and 2. 
    In Macintosh
    1Place the CD-ROM in the CD-ROM drive.
    2Double-click SAMSUNG_CLP on your Macintosh desktop.
    3Double-click User’s Guide folder.
    4Double-click User’s Guide.pdf(language). The Adobe 
    Acrobat programme opens and you can view the User’s 
    Guide.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE14
    19On the right hand side of the toner cartridge slot is a label 
    that identifies which color cartridge to fit into each slot.
    20Holding each toner cartridge, insert them into their 
    corresponding positions shown in order of Cyan, Magenta, 
    Yellow and then Black. Using both hands, grip the cartridge 
    to insert into the slot. Then hold the handle to slide the 
    cartridge in.
    When the toner cartridges are correctly installed the yellow 
    and black cartridges are not fully inserted. These will be 
    pushed into place when you close the left cover.
    C M Y
    K
    Black
    Yellow
    Magenta
    Cyan
    M
    Y
    K
    C
    Grip here.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE9
    English
    6Hold the handle on the imaging unit with the green roller 
    facing you. Align the imaging unit with the slots in your 
    printer so that the colors on both sides of the imaging unit 
    slide into the corresponding colors of the slots.
    CAUTION: Insert the imaging unit carefully so as not to scratch 
    and damage the surface of the green roller.
    7Slide the imaging unit down into the printer until it cannot 
    be pushed in any further and fold the handle down. 
    CAUTION: To prevent damage, do not expose the imaging unit to 
    light for more than a few minutes. Close the top and left cover 
    should the setup need to be halted for any reason.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: Keep the transfer belt level, do not turn the transfer belt 
    over otherwise looses toner may be spilled.
    13Slide the transfer belt down into the printer. Press it firmly 
    to make sure that it latches into place.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    CAUTION: Do not use sharp objects, such as a knife or scissors, 
    to open the toner cartridges packages. You could damage the 
    surface of the toner cartridges.
    17Holding both sides of the cartridges, gently roll them from 
    side to side to distribute the toner.
    18Place the toner cartridges on a flat surface as shown and 
    remove the paper covering on the toner cartridge by 
    removing the tape.
    NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
    and wash it in cold water. Hot water sets toner into fabric.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: When printing text at 5% coverage, you can expect a 
    toner cartridge life of about 7,000 pages for black and 5,000 pages 
    for color. 
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    TEUP: Connecting the printer to the USB port of the computer 
    requires a certified USB cable. You will need to buy a USB 2.0 
    compliant cable that is within 3m in length. 
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the USB printer cable into the connector on the back of 
    the printer. 
    3Connect the other end of the cable to the USB port on your 
    computer. 
    See the User’s Guide of your computer, if you need help.
    NOTE: To print using the USB interface, you must run Windows 
    98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
    To the USB port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    To the network 
    LAN connection
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: For Windows NT 4.0/2000/XP, the system administrator 
    should install the software. 
    All applications should be closed on your PC before beginning 
    installation. 
    1Place the CD-ROM in the CD-ROM drive. Installation will 
    start automatically.
    If the CD-ROM drive does not automatically run:
    Select Run from the Start menu, and type x:\Setup.exe 
    in the Open box (where x is the drive letter for the CD-ROM 
    drive), then click OK.
    NOTE: If the New Hardware Found window appears during the 
    installation procedure, click   in the upper right corner of the box, 
    or click Cancel. 
    ItemRequirements
    Operating systemWindows 95/98/Me/NT 4.0/2000/XP
    RAM95/98/Me 32 MB
    NT 4.0/2000 64 MB
    XP 128 MB
    Free disk space95/98/Me/NT 4.0/
    2000/XP300 MB
    Internet Explorer 5.0 or higher
    
    Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
    NOTE: If your printer is not connected to the computer, the 
    Connect Samsung CLP-550 Series window opens. After connecting 
    the printer, click Next.
    4Select the components you want to reinstall and click Next.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
    the View User’s Guide option automatically installs Adobe 
    Acrobat for you. After installing is complete, repeats step 1 and 2. 
    In Macintosh
    1Place the CD-ROM in the CD-ROM drive.
    2Double-click SAMSUNG_CLP on your Macintosh desktop.
    3Double-click User’s Guide folder.
    4Double-click User’s Guide.pdf(language). The Adobe 
    Acrobat programme opens and you can view the User’s 
    Guide.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE16
    Step 4. Loading Paper
    The tray (Tray 1) can hold a maximum of 250 sheets of plain 
    paper. You can use A4 and letter-sized paper.
    To load paper:
    1Pull the tray out of the printer.
    2Push down on the metal plate until it locks into position.
    3Flex the paper sheets back and forth to separate the pages 
    and then fan them while holding one edge. Tap the edges of 
    the stack on a flat surface to even it up.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE9
    English
    6Hold the handle on the imaging unit with the green roller 
    facing you. Align the imaging unit with the slots in your 
    printer so that the colors on both sides of the imaging unit 
    slide into the corresponding colors of the slots.
    CAUTION: Insert the imaging unit carefully so as not to scratch 
    and damage the surface of the green roller.
    7Slide the imaging unit down into the printer until it cannot 
    be pushed in any further and fold the handle down. 
    CAUTION: To prevent damage, do not expose the imaging unit to 
    light for more than a few minutes. Close the top and left cover 
    should the setup need to be halted for any reason.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: Keep the transfer belt level, do not turn the transfer belt 
    over otherwise looses toner may be spilled.
    13Slide the transfer belt down into the printer. Press it firmly 
    to make sure that it latches into place.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    CAUTION: Do not use sharp objects, such as a knife or scissors, 
    to open the toner cartridges packages. You could damage the 
    surface of the toner cartridges.
    17Holding both sides of the cartridges, gently roll them from 
    side to side to distribute the toner.
    18Place the toner cartridges on a flat surface as shown and 
    remove the paper covering on the toner cartridge by 
    removing the tape.
    NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
    and wash it in cold water. Hot water sets toner into fabric.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: When printing text at 5% coverage, you can expect a 
    toner cartridge life of about 7,000 pages for black and 5,000 pages 
    for color. 
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    TEUP: Connecting the printer to the USB port of the computer 
    requires a certified USB cable. You will need to buy a USB 2.0 
    compliant cable that is within 3m in length. 
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the USB printer cable into the connector on the back of 
    the printer. 
    3Connect the other end of the cable to the USB port on your 
    computer. 
    See the User’s Guide of your computer, if you need help.
    NOTE: To print using the USB interface, you must run Windows 
    98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
    To the USB port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    To the network 
    LAN connection
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: For Windows NT 4.0/2000/XP, the system administrator 
    should install the software. 
    All applications should be closed on your PC before beginning 
    installation. 
    1Place the CD-ROM in the CD-ROM drive. Installation will 
    start automatically.
    If the CD-ROM drive does not automatically run:
    Select Run from the Start menu, and type x:\Setup.exe 
    in the Open box (where x is the drive letter for the CD-ROM 
    drive), then click OK.
    NOTE: If the New Hardware Found window appears during the 
    installation procedure, click   in the upper right corner of the box, 
    or click Cancel. 
    ItemRequirements
    Operating systemWindows 95/98/Me/NT 4.0/2000/XP
    RAM95/98/Me 32 MB
    NT 4.0/2000 64 MB
    XP 128 MB
    Free disk space95/98/Me/NT 4.0/
    2000/XP300 MB
    Internet Explorer 5.0 or higher
    
    Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
    NOTE: If your printer is not connected to the computer, the 
    Connect Samsung CLP-550 Series window opens. After connecting 
    the printer, click Next.
    4Select the components you want to reinstall and click Next.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
    the View User’s Guide option automatically installs Adobe 
    Acrobat for you. After installing is complete, repeats step 1 and 2. 
    In Macintosh
    1Place the CD-ROM in the CD-ROM drive.
    2Double-click SAMSUNG_CLP on your Macintosh desktop.
    3Double-click User’s Guide folder.
    4Double-click User’s Guide.pdf(language). The Adobe 
    Acrobat programme opens and you can view the User’s 
    Guide.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE18
    6Pinch the paper guide as shown and move it towards the 
    paper until it lightly touches the side of the stack. Do not 
    press the guide too tightly against the edge of the paper as 
    the guide may bend the paper. 
    NOTE: If you want to change the paper size in the tray, refer to 
    the User’s Guide of your printer supplied in the CD-ROM.
    7Slide the tray back into the printer.
    NOTES: 
    • Do not push the width guide far enough to cause the material to 
    warp. 
    • If you do not adjust the width guide, it may cause paper jam.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE9
    English
    6Hold the handle on the imaging unit with the green roller 
    facing you. Align the imaging unit with the slots in your 
    printer so that the colors on both sides of the imaging unit 
    slide into the corresponding colors of the slots.
    CAUTION: Insert the imaging unit carefully so as not to scratch 
    and damage the surface of the green roller.
    7Slide the imaging unit down into the printer until it cannot 
    be pushed in any further and fold the handle down. 
    CAUTION: To prevent damage, do not expose the imaging unit to 
    light for more than a few minutes. Close the top and left cover 
    should the setup need to be halted for any reason.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: Keep the transfer belt level, do not turn the transfer belt 
    over otherwise looses toner may be spilled.
    13Slide the transfer belt down into the printer. Press it firmly 
    to make sure that it latches into place.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    CAUTION: Do not use sharp objects, such as a knife or scissors, 
    to open the toner cartridges packages. You could damage the 
    surface of the toner cartridges.
    17Holding both sides of the cartridges, gently roll them from 
    side to side to distribute the toner.
    18Place the toner cartridges on a flat surface as shown and 
    remove the paper covering on the toner cartridge by 
    removing the tape.
    NOTE: If toner gets on your clothing, wipe it off with a dry cloth 
    and wash it in cold water. Hot water sets toner into fabric.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: When printing text at 5% coverage, you can expect a 
    toner cartridge life of about 7,000 pages for black and 5,000 pages 
    for color. 
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    TEUP: Connecting the printer to the USB port of the computer 
    requires a certified USB cable. You will need to buy a USB 2.0 
    compliant cable that is within 3m in length. 
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the USB printer cable into the connector on the back of 
    the printer. 
    3Connect the other end of the cable to the USB port on your 
    computer. 
    See the User’s Guide of your computer, if you need help.
    NOTE: To print using the USB interface, you must run Windows 
    98/Me/2000/XP, or Macintosh with OS 8.6~9.2/10.1~10.3.
    To the USB port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    To the network 
    LAN connection
    %ownloadedd/romd“anuals@rinterbcomd“anuals%ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: For Windows NT 4.0/2000/XP, the system administrator 
    should install the software. 
    All applications should be closed on your PC before beginning 
    installation. 
    1Place the CD-ROM in the CD-ROM drive. Installation will 
    start automatically.
    If the CD-ROM drive does not automatically run:
    Select Run from the Start menu, and type x:\Setup.exe 
    in the Open box (where x is the drive letter for the CD-ROM 
    drive), then click OK.
    NOTE: If the New Hardware Found window appears during the 
    installation procedure, click   in the upper right corner of the box, 
    or click Cancel. 
    ItemRequirements
    Operating systemWindows 95/98/Me/NT 4.0/2000/XP
    RAM95/98/Me 32 MB
    NT 4.0/2000 64 MB
    XP 128 MB
    Free disk space95/98/Me/NT 4.0/
    2000/XP300 MB
    Internet Explorer 5.0 or higher
    
    Downloaded From ManualsPrinter.com ManualsDownloaded From ManualsPrinter.com Manuals
    NOTE: If your printer is not connected to the computer, the 
    Connect Samsung CLP-550 Series window opens. After connecting 
    the printer, click Next.
    4Select the components you want to reinstall and click Next.
    %ownloadedd/romd“anuals@rinterbcomd“anuals
    NOTE: If your computer doesn’t have Adobe Acrobat, selecting 
    the View User’s Guide option automatically installs Adobe 
    Acrobat for you. After installing is complete, repeats step 1 and 2. 
    In Macintosh
    1Place the CD-ROM in the CD-ROM drive.
    2Double-click SAMSUNG_CLP on your Macintosh desktop.
    3Double-click User’s Guide folder.
    4Double-click User’s Guide.pdf(language). The Adobe 
    Acrobat programme opens and you can view the User’s 
    Guide.
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    							SETUP GUIDE20
    Using a Parallel Cable
    NOTES: 
    • The parallel port may not be available depending on your 
    country.
    • To connect the printer to the parallel port of the computer 
    requires a certified parallel cable. You need to buy a IEEE1284 
    compliant cable that is within 3m in length.
    1Make sure that both the printer and the computer are 
    turned off.
    2Plug the parallel printer cable into the connector on the 
    back of the printer. 
    Push the metal clips down to fit inside the notches on the 
    cable plug.
    3Connect the other end of the cable to the parallel interface 
    port on your computer, and tighten the screws. 
    See the User’s Guide of your computer, if you need help.
    To the parallel port on 
    your computer
    %ownloadedd/romd“anuals@rinterbcomd“anuals 
    						
    All Samsung manuals Comments (0)

    Related Manuals for Samsung CLP 550N User Manual