Samsung CLX 8380ND User Manual

3.4   
Using the SetIP program
This program is for the network IP setting using the MAC address which 
is the hardware serial number of the  network printer card or interface. 
Especially, it is for the network admini strator to set several network IPs at 
the same time. 
The following procedure is based on windows XP. If you use Macintosh 
or Linux OS, see Software section.
Note
• You can only use  SetIP program when your machine is 
connected to a network.
• The following procedure is based on the...

3.5   
Altitude adjustment
The print quality is affected by atmospheric pressure, which is determined 
by the height of the machine above sea level. The following information 
will guide you on how to set your machine to the best print quality or best 
quality of print.
Before you set the altitude value, find the altitude where you are using the 
machine. 
1 Press  Machine Setup  on the control panel.
2 Press  Admin Setting .
3 When the login message appears, enter password with number 
keypad and press...

3.6   
Changing the display language
To change the language that appears on the display, refer to the following 
steps.
1 Press  Machine Setup  on the control panel.
2 Press  Admin Setting .
3 When the login message appears, enter password with number 
keypad and press  OK. (Page 3.5)
4 Press the  General tab.
5 Press the down arrow to switch the screen and press  Language.
6 Select the desired language.
7 Press  OK.
Setting job timeout
When there is no input for a certain pe riod of time, the machine...

3.7   
5 Press the function you want to  change, and change its settings.
For example, if you want to ch ange the default setting of the 
brightness & darkness for a copy job, press  Copy > Darkness  and 
adjust the brightness & darkness.
6 Press  OK.
Changing the font setting 
Your machine has preset the f ont for your region or country. 
If you want to change the font or set  the font for special condition such as 
the DOS environment, you can chan ge the font setting as follows:
1 Ensure that you...

4.1   
4 Loading originals and print 
media
This chapter introduces you how to load originals and print media into 
your machine.
This chapter includes:
• Loading originals
• Selecting print media
• Changing the size of the paper in the paper tray
• Loading paper
• Setting the paper size and type
Loading originals
You can use the scanner glass or DADF to load an original for copying, 
scanning, and sending a fax.
On the scanner glass
Make sure that no originals are in the  DADF. If an original is...

4.2   
To load an original into the DADF:
1 Flex or fan the edge of the paper stack to separate the pages before 
loading originals.
2 Load the originals  face up into the DADF. Make sure that the bottom 
of the original stack matches the paper size marked on the 
document input tray.
3 Adjust the document width guides to the paper size.
Caution  
Dust on the DADF glass may cause black streaks on the 
printout. Always keep it clean.
Selecting print media
You can print on a variety of print media, such...

4.3   
Specification on print media
Ty p eSizeDimensionsWeightCapacitya
a. Maximum capacity may differ depending on media we ight, thickness, and environmental conditions.
Plain paper Letter 216 x 279 mm (8.5 x 11 inches) • 60 to 90 g/m2 (16 to 24 lb 
bond) for the tray1.
• 60 to 90 g/m
2 (16 to 24 lb 
bond) for the multi-purpose 
tray
• 60 to 90 g/m
2 (16 to 24 lb 
bond) for the high capacity 
feeder • 520 sheets of 80 g/m
2 (20 lb 
bond) paper for the tray1
• 100 sheets of 80 g/m
2 (20 lb 
bond) in the...

4.4   
Media sizes supported in each mode
Guidelines for selecting and storing print media
When selecting or loading paper, envelopes, or other print materials, 
keep these guidelines in mind:
• Always use print media that conform  with the specifications listed on 
page 4.3.
• Attempting to print on damp, curled, wrinkled, or torn paper can cause  paper jams and poor print quality.
• For the best print quality, use on ly high quality copier grade paper 
specifically recommended for use in laser...

4.5   
Transparencies • To avoid damaging the machine, use only 
transparencies designed for use in laser printers.
• Transparencies used in the printer must be able 
to withstand the machine’s fusing temperature. 
Check your machine’s specification to view the 
fusing temperature, see page 15.1.
• Place them on a flat surface after removing them  from the machine.
• Do not leave them in the paper tray for long 
periods of time. Dust and dirt may accumulate 
on them, resulting in spotty printing.
• To...

4.6   
Changing the size of the paper in the paper tray
To load longer sizes of paper, such as Legal-sized paper, you need to 
adjust the paper guides to extend the paper tray.
Note 
If you have installed an optional high capacity feeder, refer to 
Quick Install Sheet to adjust paper size.
1 Adjust the paper length guide to the desired paper length. It is 
preset to Letter or A4 size  depending on the country. To load 
another size, hold the lever and move the length guide to the 
corresponding...