Samsung SyncMaster 460DRn, 460DR LCD Display User Manual

							Moves from one menu item to another horizontally or adjusts selected
menu values. When OSD is not on the screen, push the button to adjust
volume.
ENTER button [ENTER]
Activates a highlighted menu item.
SOURCE button [SOURCE]
Switches from PC mode to Video mode. Changing the source is only al-
lowed for external devices that are connected to the LCD Display at the
time.
[PC] → [
BNC] → [ DVI] → [AV] → [S-Video] → [ Component] → [HDMI]
→ [MagicInfo]
>> Click here to see an animation clip  Note
• The MagicInfo menu is available in DRn models. PIP
Push the PIP button to turn the PIP screen On / Off.
More than one PIP cannot overlap on screen as BNC and the component
use the same terminal.
>> Click here to see an animation clip
•
PC
AV / S-Video / Component / HDMI Mode
• BNC
AV / S-Video / HDMI Mode
• DVI
AV / S-Video / Component Mode
• AV / S-Video
PC / BNC /  DVI Mode
• Component
PC / DVI Mode
• HDMI
PC / BNC Mode Power button [ ]
Use this button for turning the LCD Display on and off. Brightness Sensor
The products Brightness Sensor function automatically detects the sur-
rounding brightness using a brightness sensor and adjusts its brightness\
accordingly. Introduction 
						

							Power indicator
Shows PowerSaver mode by blinking green
 Note
See PowerSaver  described in the manual for further information regarding
power saving functions. For energy conservation, turn your LCD Display
OFF when it is not needed or when leaving it unattended for long periods\
. Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
Rear
 Note
For detailed information concerning cable connections, refer to Connecti\
ng Cables under
Setup. The LCD Display s configuration at the back may vary slightly de\
pending on the LCD
Display model.  POWER S/W ON [ │ ] / OFF [O]
Switches the LCD Display On/Off.  POWER IN
The power cord plugs into the LCD Display
and the wall plug.  Introduction 
						

							 REMOTE OUT/IN
You can use a wired remote control by con-
necting it to your LCD Display.  RS232C OUT/IN (RS232C Serial PORT)
MDC(Multiple Display Control) Program Port  DVI / PC / HDMI IN [PC/DVI/BNC AUDIO
IN] (PC/DVI/BNC/HDMI Audio Connection
Terminal (Input))  DVI / PC / HDMI IN [HDMI]
Connect the HDMI terminal at the back of
your LCD Display to the HDMI terminal of
your digital output device using a HDMI ca-
ble.  DVI / PC / HDMI IN [RGB](PC Video
Connection Terminal)
Using a D-Sub Cable (15 pin D-Sub) - PC
mode (Analog PC)   DVI / PC / HDMI IN [DVI(HDCP)] (PC
Video Connection Terminal)
Using a DVI Cable (DVI-D to DVI-D) - DVI
mode (Digital PC)  
 COMPONENT AUDIO IN [L-AUDIO-R]
(Component Audio Connection Terminal (In-
put))  BNC/COMPONENT OUT [R/PR, G/Y, B/
PB, H, V] (BNC/Component Connection Ter-
minal (Output))
BNC (Analog PC) Connection: connecting
the R, G, B, H, V ports
Component Connection: connecting the PR,
Y, PB ports  BNC/COMPONENT IN [R/PR, G/Y, B/
PB, H, V](BNC/Component Connection Ter-
minal (Input))  Introduction 
						

							 AV AUDIO IN [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Input))  AV OUT [VIDEO](VIDEO Connection
Terminal)
AV mode (Output)  AV IN [VIDEO](VIDEO Connection Ter-
minal) (Input)  AV OUT [S-VIDEO] (S-VIDEO Connec-
tion Terminal)
S-VIDEO mode (Output)  AV IN [S-VIDEO](S-VIDEO Connection
Terminal) (Input)  EXT SPEAKER (8 Ω)
[- - L - +, - - R - +]
(EXT Speaker Connection Terminal)  AUDIO OUT [L-AUDIO-R] (LCD Display
Audio Connection Terminal (Output))AUDIO
OUT is the terminal for sound output of PC,
DVI or BNC.  
 LAN (LAN Connection Terminal)
(Applicable to the DRn model only)  USB(USB Connection Terminal)
Keyboard / Mouse, Mass Storage Device
Compatible.
(Applicable to the DRn model only)  Note
The number of LCD Displays that can be
connected to loopout may differ depending
on the cables, signal source etc. With cables
where there is no degradation or signal
source, up to ten LCD Displays can be con-
nected.  Note
See Connecting Cables  for further information regarding cable connections.Introduction 
						

							Remote Control
 Note
The performance of the remote control may be affected by a TV or other e\
lectronic device
operating near the LCD Display , causing a malfunction due to interferen\
ce with the frequen-
cy. ON / OFF
MagicInfo
MDC
LOCK
MagicInfo buttons
+100 DEL 
VOL
 MUTE
 TTX/MIX
 MENU
 ENTER
 P.MODE
AUTO
 ENTER/PRE-CH
 CH/P 
 SOURCE
 INFO
 EXIT
Up-Down Left-Right buttons
 S.MODE
STILL
FM RADIO
P.SIZE
 SRS
 DUAL/MTS
 PIP
 SOURCE
SWAP
 SIZE
 REW
 STOP
Introduction 
						

							 PLAY/PAUSE
 FF
1. ON / OFF Turns the LCD Display On/Off.
2. MagicInfo MagicInfo Quick Launch Button.
(Applicable to the DRn model only)
3. MDC MDC Quick Launch Button.
4. LOCK Activates or deactivates all function keys on both the remote
control and the LCD Display except for the Power and LOCK
buttons.
5. MagicInfo buttons
MagicInfo Quick Launch Button.(Applicable to the DRn model only)
• Alphanumeric: Used to enter the Internet address.
• DEL: Functions as the backspace.
• SYMBOL: Used to enter the symbols. (.O_-)
• ENTER: Used to enter values.
6. +100 DEL  Press to select channels over 100. For example, to select
channel 121, press +100, then press 2 and 1.
- This fuction does not work for this LCD Display.
7. VOL Adjusts the audio volume.
8.   MUTE
Pauses (mutes) the audio output temporarily. This is dis-
played on the lower left corner of the screen. The audio
resumes if MUTE or - VOL + is pressed in the Mute mode.
9.   TTX/MIX
TV channels provide text information services via teletext.
- This fuction does not work for this LCD Display.
10.   MENU
Opens the on-screen menu and exits from the menu screen
or closes the screen adjustment menu.
11.   ENTER
Activates a highlighted menu item.
12.   P.MODE
When you press this button, current picture mode is dis-
played on the lower center of the screen.
AV / S-Video / Component : P.MODE
The LCD Display has four automatic picture settings that are
preset at the factory. Then push button again to circle
through available preconfigured modes. ( 
Dynamic →
Standard → Movie → Custom )
PC / DVI / BNC : M/B (MagicBright) Introduction 
						

							MagicBright is a new feature providing the optimum view-
ing environment depending on the contents of the image
you are watching. Then push button again to circle through
available preconfigured modes. (
Entertain → Internet →
Text → Custom )
13. AUTO Adjusts the screen display automatically in  PC mode. By
changing the resolution in the control panel, auto function is
performed.
14.   ENTER/PRE-CH
Returns to the immediately previous channel.
- This fuction does not work for this LCD Display.
15.  CH/P In TV mode, selects TV channels.
- This fuction does not work for this LCD Display.
16.   SOURCE
Changes the video source.
17.   INFO
The current picture information is displayed in the top left
corner of the screen.
18.   EXIT
Exits from the menu screen.
19. Up-Down Left-Right but-
tons Moves from one menu item to another horizontally, vertically
or adjusts selected menu values.
20.   S.MODE
When pressing this button, the current mode is displayed at
the bottom centre of the screen. The LCD Display has a
built-in high fidelity stereo amplifier. Then press the button
again to circle through available preconfigured modes.
( Standard → Music → Movie → Speech → Custom )
21. STILL Press the button once to freeze the screen. Press it again
to unfreeze.
22. FM RADIO Turns the FM Radio on/off. In PC/DVI mode, sets the
SOUND to FM Radio. In general Video mode, selects FM
Radio, and turns off the screen. In areas where the signal is
weak, noise may occur during FM radio broadcasts.
- This fuction does not work for this LCD Display.
23. P.SIZE Press to change the screen size.
24.   SRS
SRS
25.   DUAL/MTS
DUAL-
STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM
MONO/NICAM STEREO can be operated depending on the
broadcasting type by using the DUAL button on the remote
control while watching TV.
MTS-
You can select MTS (Multichannel Television Stereo) mode.
Audio Type MTS/S_Mode Default
Introduction 
						

							FM Stereo Mono Mono
Manual
Change
Stereo Mono ↔ Stereo
SAP Mono ↔ SAP Mono
- This fuction does not work for this LCD Display.
26.   PIP
Every time you press the button, a PIP screen appears.
27.   SOURCE
Changes the source of the PIP window signal.
28. SWAP Swaps the contents of the PIP and main image. The image
in the PIP window will appear on the main screen, and the
main screen image will appear in the PIP window.
29.   SIZE
Switches the PIP Picture Size.
30.   REW
Rewind
31.   STOP
Stop
32.   PLAY / PAUSE
Play/Pause
33.   FF
Fast forwardIntroduction 
						

							Connections
Connecting a Computer
Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power\
.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV input devices such as DVD players, VCRs or camcorders as well as your\
 computer can
be connected to the LCD Display. For detailed information on connecting \
AV input devices,
refer to the User Controls under Adjusting Your LCD Display. Connect the power cord for your LCD Display to the power port on the bac\
k
of the LCD Display. Turn on the power switch.
There are 3 ways to connect the D-sub to your LCD Display. Choose one
of the following:
  Using the D-sub (Analog) connector on the video card.
• Connect the D-sub to the 15-pin, RGB port on the back of your LCD
Display and the 15 pin D-sub Port on the computer.  
Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI(HDCP) port on the back of your LCD
Display and the DVI port on the computer. 
						

							 
Using the BNC (Analog) connector on the video card.
• Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V
ports on the back of your LCD Display and the 15 pin D-sub Port on
the computer. Connect the audio cable for your LCD Display to the audio port on the ba\
ck
of your computer.
 Note
• Turn on both your computer and the LCD Display.
• The DVI cable or BNC cable is optional.
•
Contact a local SAMSUNG Electronics Service Center to buy optional items.
Connecting to Other devices Using a Power cord with Earth
•
In the event of failure, the earth lead may cause electric shock. Make
sure to wire the earth lead in correctly, before connecting the AC power\
.
When un-wiring the earth lead, make sure to disconnect the AC power
in advance.  Note
AV input devices such as DVD players, VCRs or camcorders as well as your\
 computer can
be connected to the LCD Display. For detailed information on connecting \
AV input devices,
refer to the User Controls under Adjusting Your LCD Display. Connections