Sharp Ar M201 Manual

59
7
SELECTING A SETTING FOR A USER PROGRAM
1Press the [MENU] key and then press the
[ENTER] key.
In printer mode, the user programs are accessed
by simply pressing the [MENU] key.
 
2Press the [ ] key ( ) or [ ] key ( ) to  
select the item that you wish to configure 
in the USER PROGRAM items, and then 
press the [ENTER] key.
 See USER PROGRAM (p.54 to p.58) 
for the program name and program 
code.
 You can also select a program by 
directly entering the program number 
with the numeric keys.
3Press...

USER SETTINGS
60
Audible signals (key entry beep, invalid key beep, base setting beep)
The machine sounds three different types of beep signals: a key entry beep that 
sounds when a valid key is pressed, an invalid key beep that sounds when an 
invalid key is pressed, and a base setting beep that sounds when a setting is the 
same as the base setting (base settings are explained below). The base setting 
beep is initially disabled. If you wish to enable the base setting beep, see 
SOUND AT DEFAULT on...

61
8
Chapter 8
8
Problems related to general use of the machine, the copy function, and software 
setup are explained here. Be sure to check the problem carefully before calling for 
service, as many problems can be solved by the user.
If you are unable to solve the problem, turn off the main switch, unplug the power 
cord from the outlet, and contact your authorised service representative.
DISPLAY MESSAGES
When the following indicators light up or blink on the operation panel or the following...

TROUBLESHOOTING AND MAINTENANCE
62
Error 
indicatorBlinksINSTALL A TONER 
CARTRIDGE.The toner cartridge is not installed 
correctly. Reinstall the toner cartridge.74
Steadily 
litTONER 
CARTRIDGE IS 
NEAR EMPTY.Replacement of toner cartridge will be 
needed soon. Prepare a new cartridge.74
MAINTENANCE 
REQUIRED CALL 
FOR SERVICEService by an authorised SHARP 
service technician is required.-
MEMORY FULL, PRESS START TO 
RESUME.Data is being held in memory. Print the 
data or clear it from memory.30
NO...

63
8
TROUBLESHOOTING THE MACHINE
The following problems are related to the general operation of the machine and 
copying.
ProblemCause and solutionPage
The machine does not 
operate.The machine is not plugged into a 
power outlet.
→ Plug the machine into a grounded outlet.-
Power switch OFF.
→ Turn the power switch ON.12
The power save indicator is blinking.
Indicates that the machine is warming 
up.
→ Copies cannot be made until the 
machine has finished warming up.-
The front cover or the side cover is...

TROUBLESHOOTING AND MAINTENANCE
64
ProblemCause and solutionPage
Part of the image is cut 
off or there is too much 
blank space.The original was not placed in the 
correct position.
→ Place the original correctly.20, 21
An appropriate ratio was not used for 
the size of the original and the size of 
the paper.
→ Press the [COPY RATIO] key to change 
the ratio to a setting that is suitable for 
the original and the copy paper. 25
The size of paper loaded in the tray was 
changed without changing the...

TROUBLESHOOTING AND MAINTENANCE
65
8
Paper misfeed.Misfeed occur.
→ To remove the misfeed, see MISFEED 
REMOVAL.70
The paper is outside of the specified 
size and weight range.
→ Use copy paper within the specified 
range.15
Paper curled or damp.
→ Do not use curled or crimped paper. 
Replace with dry copy paper. During 
periods when the machine is not used 
for a long time, remove the paper from 
the tray and store it in a dark place in a 
bag to prevent moisture absorption.-
Paper is not loaded...

TROUBLESHOOTING AND MAINTENANCE
66
Paper size for a paper 
tray cannot be set.Copying or printing is performed.
→ Set the paper size after copying or 
printing is complete.-
The machine has stopped temporarily 
due to running out of paper or a 
misfeed.
→ Load paper or remove the misfeed, and 
then set the paper size.16, 19, 
70
Output does not stack 
neatly in the paper 
output tray.Both ends of the paper are curled 
upward.
→ Turning the paper over in the paper tray 
may help.16
A copy job stops before...

67
8
PROBLEMS DURING SETUP OF THE SOFTWARE
If the software does not install correctly, check the following items on your computer.
To remove the software, see Removing the software (p.69).
MFP driver cannot be installed (Windows 2000/XP)
If the MFP driver cannot be installed in Windows 2000/XP, follow these steps to 
check your computers settings.
1Click the start button and then click Control Panel.
In Windows 2000, click the Start button, select Settings, and then click 
Control Panel.
2Click...

TROUBLESHOOTING AND MAINTENANCE
68
Plug and play screen does not appear
If the Plug and Play screen does not appear after you connect the machine to your 
computer with a USB cable and turn on the machine, follow the steps below to verify 
that the USB port is available.
1Click the start button, click Control Panel, and then click 
Performance and Maintenance.
 In Windows Vista, click the Start button, select Control Panel, and then
click System and Maintenance.
 In Windows 98/Me/2000, click the Start...