Sharp Projector Pg A10x User Manual

							57
Appendix
Lamp

It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-
comes 5% or less, or when you notice a significant deterioration in the picture and color quality. The
lamp life (percentage) can be checked with the on-screen display. See page 44.

For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service
of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-
rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer
or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
U.S.A. ONLY
Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.

When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.

Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.

Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to remove the damaged lamp and assure safe operation.
Replacing the Lamp
Caution
•Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching
it can lead to burn or injury.
•Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.

If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-
rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC-
PGA10X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully
change the lamp by following the instructions described in this section. If you wish, you may have
the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
Regarding the Lamp
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 57 
						

							58
1
2
3
User
service
screw
Tab
Lamp
unitBQC-PGA10X//1
Removing and Installing
the Lamp Unit
Info
•Be sure to remove the lamp unit using the
handle. Be sure not to touch the glass sur-
face of the lamp unit or the inside of the
projector.
•To avoid injury to yourself and damage to
the lamp, be sure to carefully follow the
steps below.
•Do not loosen other screws except for the
filter/lamp unit cover and lamp unit.
•Please refer to the installation manual in-
cluded with the lamp unit.
1Press  on the projector to
turn off the power.
•Wait until the cooling fan stops.
Warning!
•Do not remove the lamp unit from the
projector right after use. The lamp will
be very hot and may cause burn or
injury.
2Disconnect the power cord.
•Unplug the power cord from the AC
socket.
•Leave the lamp until it has fully cooled
down (about 1 hour).
3Change the air filter.
•Change the air filter whenever you in-
stall the lamp unit (see pages 53 and
54).
4Remove the filter/lamp unit
cover.
•Turn the projector over. Loosen the user
service screw (1) that secures the fil-
ter/lamp unit cover. Pressing the tab
(2), remove the filter/lamp unit cover
(3).
AC socket
Regarding the Lamp
Power OFF button
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 58 
						

							59
Appendix
5Remove the lamp unit.
•Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp unit
horizontal and do not tilt it.
6Insert the new lamp unit.
•Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
7Replace the filter/lamp unit
cover.
•Align the tab on the filter/lamp unit cover
(1) and place it while pressing the tab
(2) to close it. Then tighten the user
service screw (3) to secure the filter/
lamp unit cover.
Info
•If the lamp unit and filter/lamp unit cover
are not correctly installed, the power will
not turn on, even if the power cord is con-
nected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1Connect the power cord.
•Plug the power cord into the AC socket
of the projector.
2Reset the lamp timer.
•While simultaneously holding down
 and  on the projector, press
 and  on the projector.
•“LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
Info
•Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
Securing screwsHandle
1
3
2
User service screw
AC socket
Power ON button
Volume
buttons
AUTO SYNC
button
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 59 
						

							60
RS-232C Terminal:9-pin Mini DIN female connector
Pin No. Signal Name I/O Reference
1 Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 Not connected
5 SG Signal Ground Connected to internal circuit
6 Not connected
7 Not connected
8 Not connected
9 Not connected
9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor
Pin No. Signal Name I/O Reference
1 Not connected
2 RD Receive Data Input Connected to internal circuit
3 SD Send Data Output Connected to internal circuit
4 Not connected
5 SG Signal Ground Connected to internal circuit
6 Not connected
7 Not connected
8 Not connected
9 Not connected
RS-232C Cable recommended connection: 9-pin D-sub female connector
Pin No. Signal Pin No. Signal
1CD 1 CD
2RD 2 RD
3SD 3 SD
4ER 4 ER
5SG 5 SG
6DR 6 DR
7RS 7 RS
8CS 8 CS
9CI 9 CI
Note
•Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling
device (e.g. PC).
INPUT 1 RGB Signal Terminal: 15-pin Mini D-sub female connector
Connecting Pin Assignments
RGB Input1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal
14. Vertical sync signal
15. Data clockComponent Input1. PR (CR)
2. Y
3. P
B (CB)
4. Not connected
5. Not connected
6. Earth (P
R)
7. Earth (Y)
8. Earth (P
B)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
Projector
Pin No.
4
5
6PC
Pin No.
4
5
6
15
69
51
96
8
9
6
5
2143 7
5
10
151
6
11
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 60 
						

							61
Appendix
Response code format
Normal response
Problem response (communication error or incorrect command)
Command format
CONTROL CONTENTS
Power Off (Standby)
Power On
INPUT1
INPUT2
INPUT3
Lamp Usage Time (hour)OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
0~9999 P
P
I
I
I
TO
O
R
V
V
LW
W
G
E
E
TR
R
B
D
D
T_
_
_
_
_
__
_
_
_
_
__
_
_
_
_
_0
1
1
1
2
1COMMANDPARAMETERRETURN
Remaining Lamp Life (Percentage)
Lamp Status
Unit Status
Model Name Check
AV Mute Off 
AV Mute On
Auto Sync Start0~100
0:Off, 1:On, 2:Retry, 3:Waiting, 4:Lamp Error
0:Normal, 1:Temp High, 2:Fan Err,  
4:Filter Cover Err, 8:Lamp 100 hours, 
16:Lamp Burnt-out, 32:Lamp Not Lit, 
64:Temp Abnormally High
PROJECTOR NAME
OK or ERR
OK or ERR
OK or ERR T
T
T
T
I
I
AL
L
A
N
M
M
DT
P
B
A
B
B
JL
S
N
M
K
K
S_
_
_
_
_
_
__
_
_
_
_
_
__
_
_
_
_
_
_1
1
1
1
0
1
1
BUTTONS & REMOTE CONTROL KEY
PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
sold separately) to the projector. (See page 20 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Info
•When more than one code is being sent, send each command only after the response code for the previous
command from the projector is verified.
Commands
Example: When turning on the projector, make the following setting.
RS-232C Specifications and Command Settings
→
←POWR _ 1__OK
Projector Computer
Note
•If an underbar (_)  appears in the parameter column, enter a space. If an asterisk (*) appears, enter a
value in the range indicated in brackets under CONTROL CONTENTS.
Return code (0DH)C1    C2    C3   C4    P1    P2    P3    P4
Command 4-digitParameter 4-digit
O      K E      R      RReturn code (0DH)Return code (0DH)
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 61 
						

							62
Computer Compatibility Chart
Note
•This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)
mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in
“CRT only” mode. Details on how to change display modes can be found in your notebook computer’s
operation manual.
•When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen. •Multiple signal support
Horizontal Frequency: 15–70 kHz, Vertical Frequency: 43–85 Hz, Pixel Clock: 12–108 MHz
•Compatible with sync on green and composite sync signals
•SXGA+ and SXGA compatible in intelligent compression
•Intelligent Compression and Expansion System resizing technology
The following is a list of modes that conform to VESA.  However, this projector supports other signals
that are not VESA standards.
DTV
Computer
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
35.5
40.3
48.4
56.5
60.0
68.7
55.0
66.2
67.5
64.0
64.0
34.9
49.7
60.2
68.760
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
43
50
60
70
75
85
60
70
75
60
60
67
75
75
75Upscale
True
Intelligent Compression
Upscale
True
Intelligent Compression
640 × 350
640 × 400
720 × 350
720 × 400
640 × 480
800 × 600
1,024 × 768
1,152 × 864
1,280 × 1,024
1,400 × 1,050
640 × 480
832 × 624
1,024 × 768
1,152 × 870 MAC 13
MAC 16
MAC 19
MAC 21
PC
VGA
SVGA
XGA
SXGA
SXGA+
VGA
SVGA
XGA
SXGA
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Display PC/MAC/WS Resolution VESA StandardVertical Frequency
(Hz) Horizontal Frequency
(kHz)
✔
15.7
31.5
33.8
15.6
31.3
45.0
28.1
33.8
28.1
33.8 480I
480P
540P
580I
580P
720P
1035I
1035I
1080I
1080I60
60
60
50
50
60
50
60
50
60Signal Vertical Frequency (Hz)Horizontal Frequency (kHz)
A10X_A10S#E_Print#p51_62.p6503.2.4, 2:07 PM 62 
						

							63
Appendix
Troubleshooting
Check
•Projector power cord is not plugged into the wall outlet.
•Power to the external connected devices is off.
•The selected input mode is wrong.
•The AV MUTE function is working.
•Cables incorrectly connected to rear panel of the projector.
•Remote control batteries have run out.
•External output has not been set when connecting notebook computer.
•The filter/lamp unit cover is not installed correctly.
•Cables incorrectly connected to the rear panel of the projector.
•“Bright” is set to minimum position.
•Picture adjustments are incorrectly set.
(Video Input only)
•Video input system is incorrectly set.
(INPUT 1 only)
•Input signal type (RGB/Component) is incorrectly set.
•Adjust the focus.
•The projection distance exceeds the focus range.
(Computer Input only)
•Perform “Fine Sync” Adjustments (“Clock” Adjustment)
•Perform “Fine Sync” Adjustments (“Phase” Adjustment)
•Noise may appear depending on the computer.
•Cables incorrectly connected to rear panel of projector.
•Volume is set to minimum.
•If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect
operation or performance.
•See “Maintenance Indicators”.
•The keylock is set.
If the keylock is set to ON, all the buttons are locked.
Problem
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates.
Power cannot be turned
on or off using the power
buttons on the projector.
Page
15
—
27
27
16-20
13
16
54,59
16-20
36
36
45
37
22
24
38
38
—
16-20
27
—
55
43
Sound is heard but no
picture appears.
Color is faded or poor.
Picture is blurred;
noise appears.
Picture appears but no
sound is heard.
No picture and no sound
or projector does not start.
A10X_A10S#E_Print#p63_70.p6503.2.4, 2:07 PM 63 
						

							64
CheckProblemPage
Picture is green on
INPUT 1 COMPONENT.
Picture is pink (no green)
on INPUT 1 RGB.
Picture is dark.
Picture is too bright and
whitish.•Change the input signal type setting.•The lamp replacement indicator is illuminating in red. Replace
the lamp.
•Picture adjustments are incorrectly set.37
55
36
Troubleshooting
A10X_A10S#E_Print#p63_70.p6503.2.4, 2:07 PM 64 
						

							65
Appendix
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the
“Troubleshooting” section on pages 63 and 64. If this operation manual does not answer
your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
[email protected]
http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation Mexico
Branch
(525) 716-9000
http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277
[email protected]
http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
0161-205-2333
[email protected]
http://www.sharp.co.uk
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40
[email protected]
http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700
[email protected]
http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11
[email protected]
http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600
[email protected]
http://www.sharp.se
Austria Sharp Electronics Austria (Ges.m.b.H.)
0043 1 727 19 123
[email protected]
http://www.sharp.atBenelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu
Australia Sharp Corporation of Australia
Pty. Ltd.
1300-135-022
http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972
http://www.sharpnz.co.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
[email protected]
http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623
[email protected]
http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111
http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311
[email protected]
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170
[email protected]
http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
[email protected]
http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313
[email protected]
A10X_A10S#E_Print#p63_70.p6503.2.4, 2:07 PM 65 
						

							66
Specifications
LCD Projector
PG-A10X / PG-A10S
NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/
DTV480I/DTV480P/DTV540P/DTV580I/DTV580P/DTV720P/DTV1035I/DTV1080I
LCD panel × 3, RGB optical shutter method
Panel size: 0.79 (20.0 mm) (12 [H] × 16 [W] mm)
No. of dots: [PG-A10X] 786,432 dots (1,024 [H] × 768 [V])
[PG-A10S] 480,000 dots (800 [H] × 600 [V])
1–1.2 × zoom lens, F1.9–2.2, f = 26–31 mm
SHP 165 W lamp
15-pin mini D-sub connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P
B: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
[PG-A10X] 700 TV lines (DTV720P)
[PG-A10S] 520 TV lines (DTV720P)
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
9-pin mini DIN connector
12–108 MHz
43–85 Hz
15–70 kHz
ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 47 kΩ (stereo)
1.0 W (monaural)
2.8 cm round × 1
AC 100–240 V
2.4 A
50/60 Hz
240 W (Standard mode)/190 W (Eco mode) with AC 100 V
226 W (Standard mode)/182 W (Eco mode) with AC 240 V
5 W (AC 100 V) – 8 W (AC 240 V)
900 BTU/hour (Standard mode)/710 BTU/hour (Eco mode) with AC 100 V
850 BTU/hour (Standard mode)/680 BTU/hour (Eco mode) with AC 240 V
41°F to 95°F (+5°C to +35°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
11  
45/64 × 3 13/64 × 9 1/32 (297 (W) × 81 (H) × 229 (D) mm) (main body only)
11  45/64 × 3 33/64 × 9 1/32 (297 (W) × 89 (H) × 229 (D) mm) (including adjustment foot
and projecting parts)
6.4 lbs. (2.9 kg)
Remote control, Two R-6 batteries, Power cord for U.S., Canada etc. (6, 1.8 m), Power cord
for Europe, except U.K. (6, 1.8 m), Power cord for U.K., Hong Kong and Singapore (6, 1.8
m), Power cord for Australia, New Zealand and Oceania (6, 1.8 m), RGB cable (910,
3.0 m), DIN-D-sub RS-232C adaptor (5
 57/64, 15 cm), Carrying case, Lens cap (attached),
Extra air filter, Projector manual and technical reference CD-ROM, “QUICK GUIDE” label,
Operation manual
Lamp unit (Lamp/cage module) (BQC-PGA10X//1), Remote control (RRMCGA138WJSA),
Two R-6 batteries (“AA” size, UM/SUM-3, HP-7, or similar), Power cord for U.S., Canada etc.
(QACCDA016WJPZ), Power cord for Europe, except U.K. (QACCVA006WJPZ), Power cord
for U.K., Hong Kong and Singapore (QACCBA015WJPZ), Power cord for Australia, New
Zealand and Oceania (QACCLA005WJPZ), RGB cable (QCNWGA012WJPZ), DIN-D-sub
RS-232C adaptor (QCNWGA015WJPZ), Carrying case (GCASNA006WJSA), Lens cap
(CCAPHA007WJ01), Air filter (PFILDA008WJZZ), Projector manual and technical reference
CD-ROM (UDSKAA022WJN1), “QUICK GUIDE” label (TLABZA191WJZZ), Operation manual
(TINS-A505WJN1)
Product type
Model
Video system
Display method
LCD panel
Standard lens
Projection lamp
Component input signal
(INPUT1)
Horizontal resolution
Computer RGB input signal
(INPUT 1)
S-video input signal
(INPUT 2)
Video input signal
(INPUT 3)
Computer control signal (RS-232C)Pixel clock
Vertical frequency
Horizontal frequency
Audio input signal
Audio output
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
This SHARP projector uses an LCD (Liquid Crystal Display)
panel. This very sophisticated panel contains 786,432 (PG-
A10X) / 480,000 (PG-A10S) pixels (× RGB) TFTs (Thin Film
Transistors). As with any high technology electronic equip-
ment such as large screen TVs, video systems and video
cameras, there are certain acceptable tolerances that the
equipment must conform to.This unit has some inactive pixels within acceptable toler-
ances which may result in inactive dots on the picture screen.
This will not affect the picture quality or the life expectancy
of the unit.
Specifications are subject to change without notice.
A10X_A10S#E_Print#p63_70.p6503.2.4, 2:07 PM 66