Toshiba Dr410 User Manual

							41 EN41 EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
SATELLITE LINK
Note
•  If the signal of external input breaks up over 5 seconds, satellite link function will be canceled.
•  If you have not set the clock, “Clock Setting” menu will appear at step 1. Follow to step 3 in “Clock Setting” on 
page 23.
•  You cannot set the end time for the satellite link timer recording on this unit.
•  Recording picture will be distorted if the copy protection signal is being detected during satellite link timer 
recording.
•  You can record the satellite link by using S-video input jacks on the rear panel. Refer to page 42 for more 
information.
• Press [TIMER PROG.] during the satellite link timer recording to check the satellite link timer recording in 
progress.
•  When a regular timer recording and the satellite link timer recording are overlapped, those recordings are 
recorded as illustrated below.
example 2
actual
recordingtimer
recording
satellite link
example 3
actual
recordingtimer
recording
satellite link
The first 2 minutes (at the longest) will be cut off.
example 1
timer
recording
actual
recording satellite link
The first 2 minutes (at the longest) will be cut off.
E7K7AUD_D-R410KU_EN.indd   41E7K7AUD_D-R410KU_EN.indd   412007/12/14   15:03:122007/12/14   15:03:12 
						

							42 EN42 EN
SETTINGS FOR AN EXTERNAL DEVICE
IN OUT
Y
PR/CRPB/CBL
RL
RVIDEO
INVIDEO
OUT
S-VIDEOAUDIO IN
(L1)S-VIDEOAU DIO OUT
HDMI OUT
COMPONENT
VIDEO OUTDIGITAL AUDIO OUTPUTPCM / BITSTREAM  COAXIAL
front of this unitrear of this unit
1080pREC PLAY STOP SKIP1080i 720p 480pDVD -RW/R +RW/R RECORDING
I/yOPEN/CLOSEON/STANDBY
S-VIDEO VIDEO L R DV INL2
INOUT
Y
PR/CR
PB/CB
L
RL
RVIDEO
INVIDEO
OUT
S-VIDEOAU DI O  I N
(L1)S-VIDEOAUDIO OUTCOMPONENT
VIDEO OUTS-VIDEO VIDEO L R DV IN
AUDIO OUT DV-OUT
LRVIDEO
OUT S-VIDEO
OUTAUDIO OUT
LRVIDEO
OUTS-VIDEO
OUT
to L1
external device(camcorder, VCR etc.)
S-video
cable RCA
video
cable S-video
cableDV cable
(4-pin) RCA
video
cableRCA
audio
cable RCA
audio
cable
to L2 & L3
or
or
or
L2L1L3
or
Connect the external device properly to the unit by using input jacks either L2, DV IN(L3) (Front) or L1 (Rear).
When connecting an external device of monaural output to this unit, use AUDIO L jack of L2 (Front).
You must first select the desired audio from the external device before recording.
You are not allowed to select audio left or audio right during playback of self-recording discs.
Use S-video or the RCA audio/video cables for this connection.
When connecting a DVC (digital video camcorder), use the DV IN jack of L3 (Front) instead of S-VIDEO IN or VIDEO IN 
jack.
Connection to an External Device
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Note
•  When connecting an external device of monaural output to this unit, use AUDIO L jack of L2 (Front).
If you use L2 or L1 connection, make sure to select the appropriate video input type by following the steps in 
“SETTINGS FOR THE VIDEO INPUT” on page 31.
E7K7AUD_D-R410KU_EN.indd   42E7K7AUD_D-R410KU_EN.indd   422007/12/14   15:03:132007/12/14   15:03:13 
						

							43 EN43 EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
1080pREC PLAY STOP SKIP1080i 720p 480p
S-VIDEO VIDEO L R DV INL2
DVD -RW/R +RW/R RECORDING
I/yOPEN/CLOSEON/STANDBY
SETTINGS FOR AN EXTERNAL DEVICE
Recording from an External Device
1
  Turn on the TV and press 
[I/
yy ON/STANDBY], and be sure to 
select the input of the TV to which 
the unit is connected.
2
 Press [OPEN/CLOSE A] to open the 
disc tray. Place the disc to record on 
properly.
3
 Press [OPEN/CLOSE A] to close the 
disc tray.
It takes awhile to load 
the disc.
4
  Select the input of the unit which the 
external device is connected. (L1, L2 
or DV IN(L3))
•  To use the input jacks on the rear of this unit; 
Select “L1” by using [INPUT SELECT  ].
•  To use the input jacks on the front of this unit; 
Select “L2” or “DV” (L3) by using 
[INPUT SELECT 
 ].
5
  Press [REC MODE] to select a 
recording mode.
Refer to “Recording Mode” on page 30.
XP
(1Hr)SP
(2Hr)LP
(4Hr)EP
(6Hr)SLP
(8Hr)
6
 Press [I REC] on the unit to start 
recording.
7
  Start playback on the external device 
to record from.
8
 Press [C STOP] on the unit to stop 
recording.
This operation may take 
awhile to be completed. Before recording from an external device, refer to the 
instructions for the connection on page 42.
8
1
23
6
    
OPEN/
CLOSEINPUT
SELECTHDMI
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TOP MENU
CLEAR RETURNMENU/LIST WXYZ JKL MNODEF
ENTER
SKIP REV
PLAY
REC MODE ZOOMREC REPEATPA U S E
TIME SLIP
1.3x / 0.8x PLAYINSTANT SKIP
STOP FWD SKIPTIMER
PROG.
SATELLITE
LINK
INPUT
SELECTOPEN/
CLOSE
REC MODE
E7K7AUD_D-R410KU_EN.indd   43E7K7AUD_D-R410KU_EN.indd   432007/12/14   15:03:132007/12/14   15:03:13 
						

							44 EN44 EN
DV DUBBING
Guide to DV and On-Screen Display
This function helps you to easily dub the contents of the DVC (digital video camcorder) to DVD.
You can control basic operations of the DVC from the remote control of this unit such as playback, fast forward or 
reverse and stop all operations if the DVC is in video mode. Use the DV cable that has 4-pin input jack and is 
compliance with the IEEE1394 standards. When you connect to DV IN jack on the front of this unit, select “DV” position 
by using [INPUT SELECT 
 ] on the remote control and press [DISPLAY] to show the DV dubbing information for the 
operation of your DVC.
1. DV  icon
2. Indicator of active device
  •  When the “Control” is 
highlighted, press [ENTER] to 
display the item selection. Use 
[K / L] to select the device you 
wish to operate, then press 
[ENTER] to activate.
  •  Select “DVD” to control this unit.
  •  Select “DVC” to control your DVC.
3. Recording  audio  mode
  •  Other than the DVC is in stop 
mode, the “DV Audio” can be 
selected. Press [ENTER] to display 
the item selection and then use 
[K / L] to select the audio you 
wish to output. Press [ENTER] 
again to activate.
  •  Select “Stereo1” to dub the stereo 
sound.
  •  Select “Stereo2” to dub the sound 
with after recording sound.
  •  Select “Mix” to dub the stereo1 
and stereo2.
4. Indicator of dubbing function
  •  When the unit is ready for 
dubbing, “Start Rec” will appear.
  •  When the unit is in dubbing, 
“Pause Rec” will appear.
5. Channel  position
  •  When you select “DV” by using 
[INPUT SELECT 
], “DV” will 
appear.
DV
AB-1234
0:12:34
1/   1 1/   1
SP 1:00
-RWVRORGControl DVD
DV Audio  Stereo1
Start RecDV
AB-1234
0:12:34
1/   1 1/   1
SP 1:00
-RWVRORG
2
3
1
4
5
76
The menu changes according to 
what mode of DVC.
Switch the mode on the DVC to 
playback mode for the dubbing 
information. When the DVC is 
in video mode...When the DVC is not 
in camera mode...
6. Product name of your DVC
  •  If the unit cannot recognize the 
input signal from the DVC or the 
unknown product, “No Device” or 
“****” will appear instead.
7. Status of the current operation 
and the time counter
  Each icon means (Available icons 
may vary depending on the DVC):
  DVC is in stop mode.
  DVC is in playback mode.
  DVC is in pause mode.
   DVC is fast forwarding. 
(standard speed)
   DVC is fast forwarding. 
(faster than above)
   DVC is fast forwarding. 
(faster than above)
   DVC is slow forwarding. 
(standard speed)
   DVC is slow forwarding. 
(faster than above)
   DVC is slow forwarding. 
(faster than above)
   DVC is fast forwarding. 
(in stop mode)
   DVC is fast reversing. 
(in stop mode)
   DVC is fast reversing. 
(standard speed)
   DVC is fast reversing. 
(faster than above)
   DVC is fast reversing. 
(faster than above)
   DVC is in slow reverse 
playback.
  DVC is in recording.
   DVC is in recording pause 
mode. The following instructions are described with the operations using the remote control of this unit.
E7K7AUD_D-R410KU_EN.indd   44E7K7AUD_D-R410KU_EN.indd   442007/12/14   15:03:142007/12/14   15:03:14 
						

							45 EN45 EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
DV DUBBING
DVC to DVD Dubbing
Insert a recordable DVD-RW/-R or DVD+RW/+R and 
make sure your DVC is in video mode.
1
  Use [INPUT SELECT ] to select “DV”.
AB- 1234
0:00:00DV
2
  Press [REC MODE] to select a 
recording mode.
(Refer to page 30.)
3
 Press [DISPLAY].
4
  Press [ENTER] to display the item 
selection. Use [K / L] to select “DVC”, 
then press [ENTER].
DV
AB-1234
0:12:34
1/   1 1/   1
XP 1:00
-RWVRORGControl DVD
DV Audio  Stereo1
Start Rec
Before recording from DVC, see page 42 for connection 
instructions.
    
SE-R0265
OPEN/
CLOSEINPUT
SELECTHDMI
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TOP MENU
CLEAR RETURNMENU/LIST WXYZ JKL MNODEF
ENTER
SKIP REV
PLAY
REC MODE ZOOMREC REPEATPA U S E
TIME SLIP
1.3x / 0.8x PLAYINSTANT SKIP
STOP FWD SKIPTIMER
PROG.
SATELLITE
LINK
DISPLAY
ENTER
INPUT
SELECT
PA U S EPLAY
REC MODE
STOP
Instructions continue on the next page.
E7K7AUD_D-R410KU_EN.indd   45E7K7AUD_D-R410KU_EN.indd   452007/12/14   15:03:172007/12/14   15:03:17 
						

							46 EN46 EN
DV DUBBING
5
 Press [PLAY B] to find the point 
where you wish to start dubbing. 
Then, press [STOP C] where you wish 
to start dubbing.
6
 Use [K / L] to select “Start Rec”, then 
press [ENTER].
The dubbing will start.
7
 To stop dubbing; 
Use [K / L] to select “Control”, then 
press [ENTER]. 
Use [K / L] to select “DVD”, then 
press [ENTER].
Then press [STOP C].
Note for DV dubbing
•  If you press [PAUSE F] at step 5, the tape will rewind to the point a few seconds preceding the paused point. 
When you press [ENTER] at step 6, then, it will start dubbing when it comes to the paused point.
•  The unit does not send out the output signal to DVC.
•  For the proper operation, connect DVC to the unit directly. Do not connect this unit and DVC via any other unit.
•  Do not connect more than 1 DVC.
•  The unit can only accept DVC. Other DV device such as cable/satellite box or D-VHS VCR cannot be recognized.
•  If no video signal is detected from the DVC during DVC to DVD dubbing, the recording will be paused and “I” will 
flash on the TV screen. The recording will resume when the unit detects the video signal again.
•  When the DVC is in camera mode, refer to “Guide to DV and On-Screen Display” on page 44.
•  You cannot dub from DVC during timer standby mode.
•  During timer standby of either component, you cannot select L3(DV) even on the component which is not in timer 
standby.
•  Date / time and cassette memory data will not be recorded.
•  Pictures with a copy-guard signal cannot be recorded.
•  A DV terminal is a terminal that can use the transmission mode conforming to the IEEE 1394 standards called “Fire 
Wire”. It serves as the interface that connects the PC and peripheral device such as “i.Link” (registered trademark of 
SONY). It enables digital dubbing between DV devices with little degradation.
E7K7AUD_D-R410KU_EN.indd   46E7K7AUD_D-R410KU_EN.indd   462007/12/14   15:03:182007/12/14   15:03:18 
						

							47 EN47 EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
INFORMATION ON PLAYBACK
Structure of Disc Contents
The contents of DVD are generally divided into titles, and the titles are subdivided into chapters.
Audio CDs are divided into tracks.
Data disc contains MP3/JPEG are divided into folders, and the folders are subdivided into files.
DVD video
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3
Audio CD
Track 1 Track 2 Track 3 Track 4 Track 5
MP3/JPEG
folder 1 folder 2
file 1 file 2 file 3 file 4 file 5 
 
Title:  Divided contents of a DVD video. Roughly 
corresponds to a story title in short stories.
Chapter:  Divided contents of a title. This corresponds to 
a chapter in a story.
Track:  Divided contents of an audio CD.
Folder:  Divided contents of a MP3/JPEG data disc. 
Consists of number of files.
Each title, chapter, or track, folder or file is assigned a 
number, which is called “title number”, “chapter number”, 
“track number”, “folder number” or “file number” 
respectively.
Some discs may not have these numbers.
E7K7AUD_D-R410KU_EN.indd   47E7K7AUD_D-R410KU_EN.indd   472007/12/14   15:03:182007/12/14   15:03:18 
						

							48 EN48 EN
BASIC PLAYBACK
Direct Playback
1
 Press [I/yy ON/STANDBY].
Turn on the TV and be sure to select the input to 
which the unit is connected.
2
 Press [OPEN/CLOSE A] to open the 
disc tray and insert your disc with its 
label facing up.
Align the disc to 
the disc tray guide.
3
 Press [OPEN/CLOSE A] to close the 
disc tray.
It may take awhile to load 
the disc completely.
4
 Press [PLAY B] to start playback.
If you are playing back a DVD-video, a menu 
may appear.
Refer to “Using the Title/Disc Menu” on page 51.
5
 Press [STOP C] once to stop playback 
temporarily.
• Refer to “Resume Playback” on page 52.
Note
•  Some discs may start playback automatically.
     
SE-R0265
OPEN/
CLOSEINPUT
SELECTHDMI
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TOP MENU
CLEAR RETURNMENU/LIST WXYZ JKL MNODEF
ENTER
SKIP REV
PLAY
REC MODE ZOOMREC REPEATPA U S E
TIME SLIP
1.3x / 0.8x PLAYINSTANT SKIP
STOP FWD SKIPTIMER
PROG.
SATELLITE
LINK
OPEN/
CLOSE
PLAYSTOP
E7K7AUD_D-R410KU_EN.indd   48E7K7AUD_D-R410KU_EN.indd   482007/12/14   15:03:192007/12/14   15:03:19 
						

							49 EN49 EN
Disc 
Management
Recording
Playback
Introduction
Connections
Basic Setup
Editing
Function Setup
Others
BASIC PLAYBACK
1
 Press [I/yy ON/STANDBY].
Turn on the TV and be sure to select the input to 
which the unit is connected.
2
 Press [OPEN/CLOSE A] to open the 
disc tray and insert your disc with its 
label facing up.
Align the disc to 
the disc tray guide.
3
 Press [OPEN/CLOSE A] to close the 
disc tray.
It may take awhile to load 
the disc completely.
Title list will appear automatically.
•  To exit the title list, press [STOP C].
•  To resume the title list, press [TOP MENU].
4
 Use [K / L / { / B] to select a desired 
title, then press [ENTER].
e.g.) VR mode DVD-RW original
Title List
1 / 6
JAN/ 1/08 12:00AM  L1  SP 
12:00AM (0:12:00)  JAN/  1/08  L1  SP
456
123
ORG
5
 Use [K / L] to select “Play From 
Start”, then press [ENTER].
Title List
1 / 6
JAN/  1/08 12:00AM  L1  SP
12:00AM (0:12:00)  JAN/  1/08  L1  SP
456
132
ORG
Play From Start
Edit
Title Delete
Add To  Playlist
Playback will start.
6
 Press [STOP C] once to stop playback 
temporarily.
• Refer to “Resume Playback” on page 52.
To eject the disc, press [OPEN/CLOSE A] to 
open the disc tray, then remove the disc before 
turning off the unit.
Note
•  You can also start playback by pressing [PLAY B] 
instead of [ENTER] at step 5.
•  At step 4, you can press [SKIP G], or press [B] 
when the title on the lower right of the title list is 
highlighted to display the next page, and press 
[SKIP H], or press [{] when the title on the upper 
left of the title list is highlighted to display the 
previous page.
Playback from the Title List
    
SE-R0265
OPEN/
CLOSEINPUT
SELECTHDMI
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TOP MENU
CLEAR RETURNMENU/LIST WXYZ JKL MNODEF
ENTER
SKIP REV
PLAY
REC MODE ZOOMREC REPEATPA U S E
TIME SLIP
1.3x / 0.8x PLAYINSTANT SKIP
STOP FWD SKIPTIMER
PROG.
SATELLITE
LINK
ENTER
OPEN/
CLOSE
PLAY
SKIPSKIP
STOP
TOP MENU
E7K7AUD_D-R410KU_EN.indd   49E7K7AUD_D-R410KU_EN.indd   492007/12/14   15:03:202007/12/14   15:03:20 
						

							50 EN50 EN
BASIC PLAYBACK
Playing Back an Audio CD and a CD-RW/-R with MP3/JPEG Files
1
  Follow steps 1 to 2 in “Direct 
Playback” on page 48.
2
 Press [OPEN/CLOSE A] to close the 
disc tray.
It may take awhile to load 
the disc completely.
File list will appear automatically.
•  To exit the file list, press [STOP C].
•  To resume the file list, press [TOP MENU].
3
 Use [K / L] to select a desired folder 
or track/file, then press [ENTER].
File ListDISC NAME
1/ 2
A
B
1 JPEG file1
2 JPEG file2
3 MP3 file1
4 MP3 file2
5 MP3 file3
6 MP3 file4
Note
•  The audio source of MP3 files cannot be recorded as 
digital sound by an MD or DAT deck.
•  Files whose extension is other than “.mp3(MP3)” or 
“.jpg / .jpeg(JPEG)” will not be listed.
•  Some unplayable folders or files may be listed due to 
the recording status.
•  High-resolution JPEG files take longer to be displayed.
•  Progressive JPEG files (JPEG files saved in progressive 
format) cannot be played back on this unit.
•  The JPEG pictures can also rotate by using [s / B].
  When selecting track/file: 
Playback will start.
When selecting folder:
The files in the folder will appear.
Use [K / L] to select the file or folder you want to play 
back, then press [ENTER].
•  Press [PLAY B], [ENTER] or [B] to move to any lower 
hierarchies.
•  Press [s] or [RETURN] to move back to the previous 
hierarchy.
Hints for audio CD tracks and MP3 / JPEG files:
•  Folders are shown by 
.
•  Audio CD tracks are shown by 
.
•  MP3 files are shown by 
3 .
• JPEG files are shown by 
 .
•  The system can recognize up to 255 folders and, up to 
99 tracks/999 files.
•  Letters of a file/folder name overflowing the given space 
will be displayed as “…”.
• 
 If there are no files in the folder, “No Files” will be displayed.
It is recommended that files to be played back in this 
unit are recorded under the following specifications:

•  Sampling frequency  : 44.1 kHz or 48 kHz.
•  Constant bit rate  :  112 kbps - 320 kbps.

•  Upper limit  : 6,300 x 5,100 dots.
•  Lower limit  : 32 x 32 dots.
•  File size of image maximum : 12 MB.
This DVD Video Recorder requires discs/recordings to 
meet certain technical standards in order to achieve 
optimal playback quality. There are many different types 
of recordable disc formats (including CD-R containing 
MP3 files). Not all recordable discs will operate or 
produce optimal playback quality. The technical criteria 
set forth in this owner's manual are meant only as a 
guide. Use of CD-RW for MP3 files is not recommended.
You must obtain any required permission from 
copyright owners to download or use copyrighted 
content. Toshiba cannot and does not grant such 
permission.
OPEN/
CLOSEINPUT
SELECTHDMI
.@/: ABC
GHI
PQRS TUV
SPACE
SETUP DISPLAY AUDIO
TOP MENU
CLEAR RETURNMENU/LIST WXYZ JKL MNODEF
ENTER
SKIP REV
PLAY
REC MODE ZOOMREC REPEATPA U S E
TIME SLIP
1.3x / 0.8x PLAYINSTANT SKIP
STOP FWD SKIPTIMER
PROG.
SATELLITE
LINK
ENTER
OPEN/
CLOSE
PLAY
RETURN
STOP
TOP MENU
E7K7AUD_D-R410KU_EN.indd   50E7K7AUD_D-R410KU_EN.indd   502007/12/14   15:03:222007/12/14   15:03:22