Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

							(P 
Returns REQ pr en prin t is 
lete. 
tatusofPCBXXX)--Gives thestatusofall 
location LXX, Mx or ROO), Printout 
d, but 11 list all circuits 
order of circui 
Returns REQ pr en prin t is 
ete. 
CALL TNNX (Set up a monitor link frcxn Trunk 
to the remote test 
center.F--This disusedatar te test center to establish 
Onceamonitor linkhasbeene&abl 
.ishedothertnurkscanbetested. 
The trunk to be tested (B) is siezed by a 
terminal d 
and then the test number that is to be dialed, is entered via the 
terminal. TheaudioreSponsesaremonitoredatthe test center. 
The set-up sequence includes several ste& that are led by system 
Following theentry, CALL 
II the system pr ts are: 
Indicates that the first 
return 
[CR1 st be entered to 
Enter: [CR] 
ves the status of 
was idle and 
advancetothe 
o Srs WAIT indicates that the r 
(to try again) or 
[DELI [CR) ( 
oE?S CNRindicates that the reques 
system. not exist in the 
Enter: 
ElXLl[CRl toreturntotheRFQpr 
E (Directory Number)--System is requesting the number of the 
telephone to be called at the test center. 
Enter: DN followed by a [CR] 
DDL (Dialing)-System iS dialing. All 
sufficient time for the 
tobedialedandthenentera [CR] to vance theprogram. 
Enter: [CR] 
tatuS of the connection. 
t if 
lete, and the program 
vance to the next pr 
vl?REc) * 
o 
STS PDL indicates that the trunk aling 
entered.  
						

							19 P NG (PRELIMINAPY) 
PAGE 44 
Enter: [CR1 to advance the program 
o STS RLSA indicates that the trunk (A) 
S diSCOM&Xd due to a 
malfunction or soma outside influence, such as the distant end 
going on-hook or a grcund start trunk. 
the program will return to the RE1;2 pr After printing STS RLSA, 
t autcmatically.- 
s point the monitor link test center using 
established and the syst s reguesting the 
to be tested, 
Enter: CALL 
C?NNX=portnusber of the to be tested) 
Indicates that the c 
was received, A carriage return 
stbe enteredtoadvance theprcgram. 
Enter: [CR] 
~Statusb-Gives status of the connections 
f 
eque idle 
ical e to 
B-SY inticates t&t the requested trunk 
The program 
to the TRK prmpt 
toal%owanother 
t the requested trunk 
does not exist in the 
system. The program will autcxnatically return to the TRK pronpt 
etoallowanothertrunktobeselected. 
0 RLSA is cutput if the mmitor link trunk (A) was disesmlected 
to a malfunction or soma outside influence 
such as the 
stant end going on-h After printing STS the program 
11 return to the REQ 
t autamticallv. 
DN (Directory Numberb-The bunk under test (B) has been si 
system is requesting the nmber to be dialed (time, 
I etc.). 
&ter: DN foll 
by a ECRI 
(DialingF-Systt is dialing via Trumk %a. dialing is 
lete, progress tones (ringing, etc,) will be 
via the monitor link CIrunk A). When the test 
lete, enter a 
[CR] toreleaseTnmkBandretxrntotheTPX 
Enter: [CRlwhentestisconplete 
_ 
STS TM, DDL, PLSA, or PLSB (Status)--Gives status of the connection, 
0 STS TLK will be printed in response to a [CR] entered following 
thedialing proxpta&ve, 
The [CR] released the trunkunder test 
(B), therefore the cutput indicates the status of the monitor link 
(A). The program will automatically return to the TRK 
allowanother tnlnktobe selected. 
o STS 
DDL will be printed if a [CR] was entered before dialing 
This state is the samas 
DDLatmve. 
0 be printed if the monitor link (Trunk A) is released 
unction or scme c&side influence. 
The trunk under 
also be released and the program 11 return to 
the 
0 if the trunk under test (Trunk B) is 
ue to a ma nction or scme outside influence. 
program will aut 
tically return to the TRK pr 
mother trunk to be selected.  
						

							19 
e: tor link trunk (A) 
center DN = 730-5000 
Test DN = 730-0002 
t 03) 21 
UNEQ=N3FCBinthat 
UIUS=PCBisqui 
2. Status: IDL=Idle 
lyaisabl 
rtdisabl 
DIS TKMsOftWare disabled 
es faulty 
1 
* nse is 
. 
/  ,   / 1 I 
: 
Level 3 given in the Adhorization Pr 
error e is 
given. 
given in the Authorization pr 
. 
esent 
: 
. 
gives then  
						

							6 
Ctl X=Igmre line entered 
3,  
						

							Nov. 84 PROGRAMMING (PRJ%IMINARU P?GE 47 
D 
Authorization Procedure rmst be ccmpleted. If an OK response is 
received, proceed as follows: 
Ieast Cost Routinq 
All Paqe Access Cede 
ita nN 17 ill-a 
NOTES: 
1. All Page access code = 1, 2, or 3 digits. 
2. N= number dialed in place of * or V#l. 
3. Bewaxe of conflicts with the numbering plan and access codes--system will 
not always check.  
						

							Nov. 84 
PROGRAMMING (PRELIMINARY) PAGE 48 
4. CFDNA TIMER must be > RNA or RNA will prevail. 
5. DPT timer also controls A!IT LPK release. 
6. A IgYtq response allows calls from 
to a Hahdsfree Answerback 
equippedEE?TtobeansweredHands 
7. A *Y* response allows calls from the Attendant to a Handsfree Answerback 
equippedEXTto be answe.redHandsfree. 
8.CtlX= Ignore line entered 
CtlH= 
I3ackspace ,‘ 
DEL = Stop printing and return to REQ 
DELDEL= Abortprogram ,^ 
9~ I‘ ; 
p; 
* 
Authorization Procedure nust be coqleted. If an OK response is 
received, proceed as follows: 
1. a) The 3-character feature name followed by a space and its aocess code is 
entered in response to FIT?. 
b) The featuresmaybeenteredin any order and thenewaccess code 
overwrites the existing one. 
c) Any feature code which is to be unchanged need not be entered. 
d) The feature abbreviations and factory assigned codes are:  
						

							: 
Nov, 84 
PRGRMMING (PRELIMINARY) 
PzlGE 49 
*I 
I /, 
Ja,.. 
la-1 
h-L--- 
-*. - . 
Call PiT3G$ 
1 Hold-All Calls 
Universe Night 
Charqe Acca 
Flash 
Paqing Zone 
O  4-a P inu Zone 1 
.nff Zone Z I - 
I P 
, I men I I 
1C I 
-- #2 I 
Q#2 
2.(xX= 
Ignore line entered 
Ctl H = Backspace 
DEL 
= Stop printing and return to RFl;z 
D&DEL,= 
Abort program  
						

							Nov. 84 
PRCGRAMMI~ (PRELIMINARY) PAGE 50 
Authorization Procedure nust be ccsrrpleted. If an OK response is 
received, proceed as follows: 
NOTES: 
1, NN= PCB location 
2. X = Circuit number 
3. A maxim of two key strips are possible: lo-key EXT = 1; 20-key EXT = 2. 
4. There are 16 different COS groups which are defined in the COS Data BLock. 
5. There are maximum of 32 Call Pick---up Groups, 
6. Classes 0 - 
7 are defined in the Toll Restriction Data Block (DIOL) IQ ~0:; p-* )I 
Program. Class 8 is 0, 1 restriction. 
ne is no Toll Restriction. 
7. I+Jlaximum of 30 Displ 
s assigned. 
8. Enter key nu&er f 
by a space and then the entry. 
See Table Fl for 
possible entry. 
9, Key numbers may be entered in any order and the KEY 
pr 
t will be 
re,oeated until DEL is 
. 
10. If KS was ZZr O-19 is al 
11. Ctl x= Ignore line entved 
Ctl H=Backspace 
DEL = Stop printing and return to RnQ 
DEL DEL,= Abort program  
						

							Nov. 84 
PRGFGMMING (P-1 PiaGE 51 
I Voice Paqe 
I 
lWTES: 
1. NNN = Direct 
XXX= HuntD 
Distributed,, to remove present DN. 
Also see Station Hunt - 
2. NX is entered in place of the usual hunt DN following the EKT DN 
assignment. 
For exanp?le: N = 
Distributed Bunt Group Number (0 - 
---. ./ 
X =&xnberMmber(1-8) 
j. XXX =?LDN assigned in Trunk Data Block. 
4. Maximum ADL keys for entire system is 250. 
5. Flash key causes a 
6. LmJx= m.sec. flash (line open) to CO line. 
Port number of m to be signalled. 
7. SDC XX makes the station a controller of list #XX, 
SW XX makes the station a user of list #XX. 
Maximum: 25 personal, lo-nuder Speed Dial-Station lists (XX = 1 -- 251, 
8. XXX = DN of station receiving Voice Page. 
If 
appearances, the station having the DN as Pri e DN has nailtiple 
(key 0) will be called.  
						

							Nov. 84 PIuxmmMING(PRELLMINARY) 
PPGE 52 
I I No mrt (destination of the key feature) is assianed 
I 
,A...: --A23 is 250). 
ntered but PUG key already assiqned). 
EREXT 22 PVR NNN, PVN NNN is entered but trunk DN NNN is not yet assiqned. 
I 
! EREKT 23 ! The inmt DN is trunk DN (VCP NNN Hunt DN), 
imm nuher of Display EXTs already assigned bxinaum in 
30).