Toshiba Strata Se, Strata Vie General Description Manual

							TABLE 29 
PROGRAM 104/106 
OTHER COMMON CARRIER AUTHORIZATION CODE LENGTHS #l and #2 
1) Lock in the SET switch on the HKSU. 
2) Depress the m key on station 13/l 7. 
3) Dial 0 =I(0 11) n the dial pad. 
4) Refer to the System Record Sheet. 
This program definesthe lengthsof the autho- 
rization codes for OCC #l & #2. These 2-digit 
numbers are entered via the dial pad. SET LED on. 
Station 13/17 LED 19 on. , 
System is in program mode. 
Normal functions halt on station 13/17. 
SPKR LED steady on. 
SPKR LED flashes continuously. 
The various LEDs indicate present data. 
As each digit is entered, the entry is verified by 
LEDs as shown below. 
PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
Key/LED/ Start ) 1st Digit 
2nd Diqit 
Binary Numbers: 
03 
X = LED on 
02 
All LEDs off = no data 
01 
00 
5) Depress the m key to place new data in 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. All station 13/l 7 LEDs (except 19) go off. 
New data is stored, previous data is erased. 
SET LED goes off. 
Station 13/l 7 LED 19 aoes off 
r(m rc. 
rl”IL. 
Program 106 follows the same procedure as Program 104. 
Program 106 defines the length of OCC#2 authorization code.’ 
-55-  
						

							TABLE 30 
PROGRAM 108/l 09 
TOLL RESTRICTION OVERRIDE CODES #l and #2  PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
1) Lock in the SET switch on the HKSU. 
X = LED on 
All LEDs off = no data 
66) Transfer data into working memory per Par- 
NOTE. 
Program 5#W LED 13 enables stations to use Toll Restriction Qverride Codes 1 & 2. 
-56-  
						

							TABLE 31 
PROGRAM 1X0 
TOLL RESTRICTION CLASS PARAMETERS 
( SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
2) Depress the m key on station 13/l 7. Normal functions halt on station 13/l 7. 
SPKR LED steady on. 
3) Dial aa 1 on the dial pad. 
4) Refer to the System Record Sheet. 
Using the various keys, turn their associated 
LEDs on or off, as required. The detailed 
meaning of each key/LED is shown below. 
NOTE. 
If any key/LED is not shown,.it is not used. SPKR LED flashes continuously. 
An LED indicates present data. 
An X on the record sheet means the LED shoulc 
be on. 
If the LED is already on, depressing the associatec 
key will turn it off and vice versa. LEDs may be 
turned off and on until the desired pattern is set. 
PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
KEY/LED 
LED ON LED OFF 
02 
Area code f 555 + XXXX-Allowed Not Allowed 
01 
01 or 01 1 Overseas Restricted Allowed 
00 0 + Restricted Allowed 
5) Depress the m key to place new data in 
All station 13/l 7 LEDs (except 19) go off. 
memory. 
6A) Go.to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
-57-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 32 
PROGRAM 1 XY 
TOLL RESTRICTION CLASS AREA CODE ENTRY 
(LCD TELEPHONE REQUIRED) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode., 
Normal functions halt on station 13/l 7. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dia; 015 (Allow), iag(Deny) or flnl(Display) LCD is blank. 
SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 4.) LCD displays dialed number. 
1 X 2 = LCD is blank. 
4) Press /J key. 1 X 3 = LCD is blank. 
1 X 4 = LCD displays all allowed codes. 
5) Enter first area code in range sequence LCD displays code entered. 
(start). 
6) Depress 1 key.* LCD shifts left to provide space for next code. 
7) Enter final area code in range sequence LCD displays code entered. 
(stop).* 
8) Depress 1 key. LCD is blank. 
9) Return to Step 5 to enter additional area 
codes. 
10) Depress the m key to place new data in All station 13/17 LEDs (except 19) go off. 
memory. 
11A) Return to Step 2 in order to continue with 
this program 
. . . or . . . 
116) Go to Step 2 in another program table 
. . . or . . . 
1 1 C) Tidnsfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one.area code in sequence is being entered. 
-58-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 33 
PROGRAM 1XZ 
TOLL RESTRICTION CLASS OFFICE CODE ENTRY 
(LCD TELEPHONE REdRED) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 13/l 7. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD is blank. 
3) Dial OUj (Allow), OIa(Deny) or ~~~(Display) SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 4.) , 
-- LCD disp!ays dialed number. 
1 X 6 = LCD is blank. 
4) Press g k‘ey. 1 X 7 = LCD is blank. 
1 X 8 = LCD displays all allowed codes. 
LCD displays code entered.  5) Enter first office code in range sequence 
(start). 
6) Deoress P kev:* 
7) Enter final office code in range sequence 
(stop).* 
8) Depress 3 key. 
9) Return to Step 5 to enter additional office 
codes. 
10) Depress the m key to place new data in 
memory. 
1 1A) Return to Step 2 in order to continue with 
this program 
. . . or . . . 
116) Go to Step 2 in another program table 
. . . or . . . 
11C) Transfer data into working memory per 
1 Paragraph 02.06. LCD shifts left to provide space for next code. 
LCD displays code entered. 
LCD is blank. 
All station 13/l 7 LEDs (except 19) go off. 
SET LED goes off. 
Station 13/l 7 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one office code in sequence is being entered. 
-59-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 34 
PROGRAM 2XY 
TOLL RESTRICTION AREA/OFFICE CODE EXCEPTION TABLE 
(LCD TELEPHONE REQUIRED) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. s 
Normal functions halt on station 13/l 7. 
LCD is blank. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
LCD is blank. 
3) Dial aafl (X 
q Table 1 - 8). LCD displays dialed number, then shifts left to pro- 
vide space for next entry (or displays current area 
code). 
4) Enter area code. 
5) Depress them key. 
6) Depress the m key. LCD clears and displays area code entered. 
Binary data is shown on LEDs 00 - 03. 
LCD is blank. 
SPKR LED steady on. 
LCD is blank. 
7) Dial gaz (Allow), 311 (Deny) or gIa(Display) SPKR LED flashes continuously. 
as required. (X = Restriction class 1 - 8.) LCD displays dialed number. 
2 X 2 = LCD is blank. 
8) Press 3 key. 2 X 3 = LCD is blank. 
2 X 4 = LCD displays all allowed codes. 
9) Enter first office code in range sequence LCD displays code entered. 
(start). 
10) Depress 1 key.” LCD shifts left to provide space for next code. 
11) Enter final office code in range sequence LCD displays code entered. 
(stop).” 
12) Depress 3 key. LCD is blank. 
13) Return to Step 5 to enter additional office 
codes. 
14) Depress the m key to place new data in All station 13/l 7 LBDs (except 19) go off. 
memory. 
15A) Return to Step 2 in order to continue with 
this program 
. . . 
or . . . 
15B) Go to Step 2 in another program table 
. . . or . . . 
15C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 13/17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 10 and 11 if only one office code in sequence is being entered. 
-6O-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 35 
PROGRAM 1X1 
TOLL RESTRICTION CLASS AREA/OFFICE CODE EXCEPTION TABLE SELECTION 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 13/l 7 LED 19 on. 
System is in program mode. ’ 
Normal functions halt on station 13/17. 
2) Depress the m key on station 13/l 7. SPKR LED steady on. 
3) Dial gailon the dial pad. (X = Restriction class 
SPKR LED flashes continuously. 
1 - 4, as defined in Program 6Xx.) 
The various LEDs indicate present data. 
4) Refer to the System Record Sheet. An X on the record sheet means the LED should 
Using the various keys, turn their associated be on. 
LEDs on or off, as required. The detailed If the LED is already on, depressing the associated 
meaning ‘of each key/LED is shown below. key will turn it off and vice versa. LEDs may be 
NO 
JE. turned off and on until the desired pattern is set. 
If any key/LED is not shown, it is not used. 
this program 
68) Go to Step 2 in’ar-%-rer program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
-61-  
						

							TABLE 36 
PROGRAM 1#00 
LEAST COST ROUTING HOME AREA CODE ENTRY 
(LCD EKT REQUIRED-STRATA Vie only)  PROGRAlWMlNG PROCEDURES 
SECTION 500-0~6-300 
JANUARY 1988 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. , 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial 1311 on the dial pad. SPKR LED flashes continuously. 
LCD: DATA = (indicates present data) 
4) Refer to the System Record Sheet. LCD: (displays code entered) 
Using the dial pad, enter the system’s home 
area code. 
NOTE. 
To clear existing data without entering a 
new number, depress the 0 key once for 
each digit. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-62-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY1988 
TABLE 37 
PROGRAM l#OX 
LEAST COST ROUTING SPECIAL CODES 
(LCD EKT REQUIRED-STRATA Vie only) 
1) Lock in the SET switch on the HKSU. SET LED on. 
Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
I 1 LCD: PROGRAM MODE 
I 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
I 
3) Dial ilafl on the dial pad. X = 1 - 5 corre- SPKR LED flashes continuously. 
sponds to five different special codes that LCD: DATA = (indicates present 
data) 
may be entered. 
4) Refer to the System Record Sheet. LCD displays code entered. 
Using the dial pad, enter -the special code 
1 5) Depress the m key to place new data in 1 All station 17 LEDs (except 19) go off 
memory. . 
6A) Go to Step 2 in another program table 
. . . or . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-63-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 38 
PROGRAM 1#06 
LEAST COST ROUTING PARAMETERS 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial i pa 1 on the dial pad. 
SPKR LED flashes continuously. 
LCD: (displays program number) 
Various LEDs indicate present data. 
4) Refer to the System Record Sheet. 
LCD displays code entered. 
Using keys 00 
- 02, turn their associated 
LEDs ON or OFF, as required. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-64-