Toshiba Strata Se, Strata Vie General Description Manual

							TABLE 39 
PROGRAM 1#07X 
SELECT LONG DISTANCE INFORMATl,ON (LDI) ROUTE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
’ 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the w key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial DaaJ on the dial pad. SPKR LED flashes continuously. 
LCD: DATA = 8 
- 
4) Refer to the System Record Sheet. LCD displays code entered. 
Using the dial pad, enter X (X = 1 - 8, corre- 
sponding to one of eig-ht route table 
numbers). 
5) Depress the m 
key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . . 
66) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
-65-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 40 
PROGRAM 1#08X 
SELECT LOCAL CALL ROUTE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. ’ 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.?. 
3) Dial 0119 on the dial pad. SPKR LED flashes continuously. 
LCD: DATA = 8 
4) Refer to the System Record Sheet. LCD displays code entered. 
Using the dial pad enter X. X = 1 - 8, corre- 
sponding to one of eight r.oute table numbers. 
5) Depress the lm key to place new data in All station 17 LEDS (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-66-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 41 
PROGRAM 1#09 
DIAL ZERO (0) TIMEOUT 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. 
3) Dial ij J 2 1 on the dial pad. SPKR LED steady on. 
LCD: PROGRAM NO.? 
SPKR LED flashes continuously. 
LCD: (displays dialed number) 
An LED indicates present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using one key (00 - 03), turn its associated be on. 
LED ON or OFF as required. 
Only one LED is permitted to be on; depressing an- 
NOTE: other key will turn that LED on and turn off the pre- 
Only one LED may be on at a time. vious LED. 
5) Depress the m key to place new data in 
All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. , . or . . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. 
SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-67-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 42 
PROGRAM 1 #XY 
LEAST COST ROUTING AREA CODE TABLE 
(LCD TELEPHONE REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. .% 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial flpI1 (Allow), 0 ilg (Delete) or igfly SPKR LED flashes continuously. 
(Display) as required. (X = Route Table 1 - 8.) LCD: (displays dialed number) 
1 # X 2 LCD: DATA = 
4) Press 8 key. 1 # X 3 LCD: DATA = 
1 # X 4 LCD: (displays all allowed codes) 
5) Enter first area code in range sequence LCD: (displays code entered) 
(start). 
6) Depress 9 key.* LCD: (shifts left to provide space for next code) 
7) Enter final area code in range sequence 
LCD: (displays code entered) 
(stop).* 
8) Depress 1 key. Number temporarily stored. 
9) Return to Step 5 to enter additional area 
codes. 
3 0) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
1 1A) Return to Step 2 in order to continue with 
this program 
or . . . 
1 1 B) Go to Step 2’in’another program table 
. . . or . . . 
1 1 C) Transfer data into working memory per 
Paragraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 6 and 7 if only one area code in sequence is being entered 
-68-  
						

							TABLE 43 
PROGRAM l#X8Y 
LEAST COST ROUTE DEFINITION 
(LCD EKT REQUIRED-STRATA Vie only) 
PROGRAMMING PROCEDURES 
SECTION 5904236-300 
JANUARY1988 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.?. 
3) yial IiDgu on the dial pad. X q Route Table SPKR LED flashes continuously. 
- 8; Y = Route Definition 1 - 4. LCD: DATA = 
4) Refer to the System Record Sheet. LEDs 00, 01, 02 & 03 show data in binary format. 
Using the dial pad, enter 
the Route Definition LEDs 10 & 11 indicate which digits are being dis- 
number and Modified Digits Table number. played. 
5) Depress the [ma key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Go to Step 2 in another program table 
. . . or . . 
6B) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous 
data is erased. 
-69-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 44 
PROGRAM l#X50 - 53 
START TIME A SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial fllail - 8 a on the dial pad. X = Route SPKR LED flashes continuously. 
Table 1 - 8. LCD: (displays dialed number) 
-- 
4) Refer to the System Record Sheet. LCD: (displays code entered) 
Enter the required data for 50- 53 via the dial 
pad. 
5) Depress the i5nr;l key to place new data in All station 17 LED.s (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this progra’m 
6B) Go to Step 2 in’an:ther program table 
. . . or . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-7o-  
						

							PROGRAMMING PR-OCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 45 
PROGRAM l#X60 - 63 
START TIME B SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. s 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial EIgIja - Jg on the dial pad. X = Route SPKR LED flashes continuously. 
Table 1 - 8. LCD: (displays dialed number) 
4) Refer to the System Record Sheet. LCD: (displays code entered) 
Enter the required data for 60- 63 via the dial 
pad. 
5) Depress the TxITIT;I key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or . . . 
66) Go to Step 2 in’another program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-71-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 46 
PROGRAM l#X70 - 73 
START TIME C SCHEDULE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. I 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial [ifljl - jgon the dial pad. X = Route SPKR LED flashes continuously. 
Table 1 - 8. LCD: (displays dialed number) 
4) Refer to the System Record Sheet. 
LCD: (displays code entered) 
Enter the required data for 70 - 73 via the dial 
pad. 
5) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
6A) Return to Step 2 in order to continue with 
this program 
or . . . 
66) Go to Step 2 in’another program table 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-72-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 47 
PROGRAM 1#9XY 
MODIFIED DIGITS TABLE 
(LCD EKT REQUIRED-STRATA Vie only) 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 LED 19 on. 
System is in program mode. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the B key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial JQ]naon the dial pad. X = Modified Dig- SPKR LED flashes continuously. 
its 
Tsblt 1 - 6, Y = (0) delete, (I) add. LCD: (displays dialed number) 
Various LEDs indicate present data. 
4) Refer to the System Record Sheet. LCD: (displays digits entered) 
Using the dial pad: 
A) Delete Table:,Enter the quantity of digits to 
KEY/LED PAUSE 
be deleted from the dialed number. 08 16 
B) AddTable:Bntertherequiredmodifieddig- 
its to be added to the dialed number. To in- 07 14 
sert pauses (see table for duration in sec- 06 12 
onds) while adding digits, press the 05 10 
appropriate key when pause is required. 04 8 
I 
NOTE. 
Digits may be added or deleted in the same 
Modified Digits Table. 
r 
5) Depress the m key to place new data in station 17 LEDs (except 19) go off. 
memory. I 
6A) Return to Step 2 in order to continue with 
this program 
ES) ? 
Lc tc Step 2 in’anyth;r progran; tabla 
. . . or . . . 
6C) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station 17 LED 19 goes off. 
New data is stored, previous data is erased. 
-73-  
						

							PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
TABLE 48 
PROGRAM 2#XY 
LEAST COST ROUTING AREA/OFFICE CODE EXCEPTION TABLE 
(LCD EKT REQUIRED-STRATA Vie only) 
I) Lock in the SET switch on the HKSU. SET LED on. 
Station 17 LED 19 on. 
Normal functions halt on station 17. 
LCD: PROGRAM MODE 
2) Depress the m key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
3) Dial 3113 1 on the dial pad. X = Area/Office SPKR LED & LED 10 flash continuously. 
Code Table 1 - 8. 
4) Refer to System Record Sheet. 
Enter Route Table number (1 - 8). 
5) Depress the m key. LCD: (displays table number) 
5) Depress the lm key on station 17. SPKR LED steady on. 
LCD: PROGRAM NO.? 
7) Dial 5 11 i] on the dial pad. X = Area/Office LCD: (displays dialed number) then . . . 
Code Table 1 - 8. DATA = 
3) Enter Area Code via the dial pad. LCD: (displays area code entered) 
3) Depress the m key. 
10) Depress the m key. SPKR LED steady on. 
LCD: PROGRAM NO.? 
1 1) Dial iiai(Add), ajna(Delete), or ~p~~(Dis- SPKR LED flashes continuously. 
play). X = Area/Office Code Table 1 - 8. LCD: (displays dialed number) 
2 # X 2 LCD: DATA = 
12) Depress i key. 2 # X 3 LCD: DATA = 
2 # X 4 LCD: (displays all currently programmed 
off ice codes) 
13) Enter first Area Code in range sequence LCD: (displays code entered) 
(start). 
14) Depress 1 key.* LCD: (shifts left to provide space for next code) 
15) Enter final Area Code in range sequence LCD: (displays code entered) 
(stop).” 
16) Depress 3 key. 
17) Return to Step 10 to enter additional Area 
Codes. 
18) Depress the m key to place new data in All station 17 LEDs (except 19) go off. 
memory. 
19A) Go to step 2 in, another program table 
. . . or . . . 
196) Transfer data into working memory per Par- 
agraph 02.06. SET LED goes off. 
Station. 17 LED 19 goes off. 
New data is stored, previous data is erased. 
“Skip Steps 14 and 15 if only one area code in sequence is being entered. 
-74-