Toshiba Strata Vie General Description Manual

INSTALLATION PROCEDURES 
SECTION 300-006-200 
MAY 1986 
-.-_.-_ a- -_-__._.a. a__._ l-IGUHt 35-I tHMlNAL S I HIP 
10.31 Strata WE provides access to an 
external paging system by dialing two digits 
(89). The single output connection is made via 
the 8/600 terminals on the left side panel, and 
can be used in one of three ways: 
a) To operate customer-provided speaker 
directly via an internal 3-watt amplifier 
located on the SEPU PCB. 
b) If more than 3 watts are required, an exter- 
nal...

INSTALLATION PROCEDURES 
SECTION 300-006-200 
MAY 1906 
1 Mute 2 -J output 
Volume 
Input 1 
4) 
,, Input 2 7 
Level 
1 input 2 
. Leve! 
FIGURE 37 
FIGURE 38 
EXTERNAL AMPLIFIER HOOK-UP 
switch must be set at “600”. The SMQU am- 
plifier is not used for the 600-ohm mode in 
order to permit a 2-way voice path. 
VOLUME SETTING CoNTRO&S 
control on the right-hand side of the EKTs. 
10.63 The EX.SP volume control on the left 
side panel will not function when the 600-ohm 
mode is selected. 10.75 If a...

4) Using the volume control on the MOH 
source, adjust MOH to the most comfortable 
level without distortion. 
5) If a higher level is needed than can be pro- 
vided by the MOH source, turn the MOH vol- 
ume control slowly clockwise to achieve the 
most comfortable level without distortion. 
6) Release the connection between the two 
CO lines. 
7) No further changes should be made using 
the MOH control or the MOH source 
volume 
control. 
10.83 
If an external speaker is to be used in 
the system;...

INSTALLATION PROCEDURES 
SECTION 300-006-200 
MAY1966 
10.93 The W3 strap option on the VMAU 
allows the NR relay to function in one of two 
modes: 
a) Answering Machine Control-if the W3 
strap remains intact, the relay is operated con- 
tinuously when the-system is in Night Service. 
This mode is intended for indirect control of an 
answering machine. 
b) Night Bell Control-if the W3 strap is cut, 
the relay pulses at a 1 -second on, 3-second off 
rate when the system is in Night Service and 
an...

TOSHIBASYSTEM PRACTICES 
ELECTRONIC KEYTELEPHONE SYSTEM PROGBAMMING PROCEDURES 
SECTION 300-006-300 
MAY1986 
Strata V;I, 
PROGRAMMING PROCEDURES  

TOSHIBA 
Strata”= 
TECHNICAL BULLETIN 
1 
TB 026-8605 
November 1, 1986 Page 
1 of 1 
DSS Feature Key Programming 
On the STRATA We, Xlle & XXe ‘systems, a maximum of two keys ma 
be programmed as DSSl and DSS2 on each station. The m and @ 
d 
keys function as both Direct Station Selection (DSS) and Busy Lamp Field 
(BLF) feature keys. 
It is recommended that a maximum of four DSS keys be directed-to+ one 
_ 
station (Program 4#XX). Example: Stations 13, 22, 15 and 12 all have DSS 
keys directed to...

TOSHIBASYSTEM PRACTICES 
ELECTRONIC 
KEY TELEPHONE SYSTEM 
Strata VI, 
PROGRAMMING PROCEDURES 
TABLE of CONTENTS 
PARAGRAPH SUBJECT PAGE 
PROGFIAMMlNG PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
TABLE of CONTENTS 
ILLUSTRATION LIST 
. : : : : : : : 
TABLE LIST 
01 INTRODUCTION ’ : : : : : : : : : : 
02 PROGRAMMING PROCEDURES . . 
02.00 General . . . . . . . . . . . . 
02.10 Multiple Station Programming. . . 
02120 Using 1 O-key EKT for Programming 
02.30 Preparation . . . . . . . . . . 
02.40 System...

TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 ~ 
TABLE 
1 
2 
3 
4 
5 
6 
7 
B 
9 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
30 
31 
32 
33 
34 
35 
36 
37 
38 
39 
Strata VI, 
PROGRAMMING PROCEDURES 
TABLE LIST 
TITLE 
PAGE 
Hold Recall Time Code 
........................ 10 
initialized Data 
........................... 12 
Program 01 -System Assignments (Basic) 
............... 16 
Program 02-System...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
01 
INTRODUCTION 
01 .Ol The data governing overall system 
operation and feature execution for the 
Strata We system is stored in read-only- 
memory (ROM) and cannot be altered in the 
field. However, the data controlling operation 
of the various options, both system and sta- 
tion, is stored in random-access-memory 
(RAM) and can easily be changed according to 
individual installation requirements. 
01.02 All Strata options are controlled by...

PROGRAMMING PWOCEDURES 
SECTION 300-006-300 
MAY 
1986 
into working memory per Paragraph 02.06. 
Station option data (with the exception of 
CO line access assignments) are written 
into the main data memory; therefore, all 
chanaes are effective immediatelv after the 
key is depressed. However, it is rec- 
ommended that the data transfer proce- 
dures per Paragraph 02.06 be utilized for 
added programming protection. 
02.06 Data may be secured in working 
memory in one of two ways: 
1) If the system is...