Xerox Documate 4830 User Guide

Xerox® DocuMate® 4830 Scanner Welcome
2User Guide
•Microsoft® Windows® operating system: 
– 32-bit Windows XP (Service Pack 3)
– 32-bit or 64-bit Windows Vista (Service Pack 2)
– 32-bit or 64-bit Windows 7 (Service Pack 1)
– 32-bit or 64-bit Windows 8 / 8.1
– 32-bit or 64-bit Windows 10
• 2 gigabyte (GB) internal memory (RAM)
• Minimum available hard disk space:
– 350 MB for the scanner driver
– 750 MB for Visioneer OneTouch
– 1 to 2 GB for each additional application
Please refer page 14 for a list of...

Welcome Xerox® DocuMate® 4830 Scanner
User Guide3
Xerox® DocuMate 4830 Scanner
1.Input Tray—Holds the documents in the Automatic Document Feeder for scanning. 
2.Paper Guides—Guides adjust to support various document widths.
3.ADF Cover—Pull to open the Automatic Document Feeder.
4.Scanner Lid—Lift lid to place an item on the flatbed glass for scanning.
5.Control panel—OneTouch scanning controls.
–LED Number—The selected OneTouch function for the Simplex and Duplex buttons.
–Function buttons—Selects the...

Xerox® DocuMate® 4830 Scanner Welcome
4User Guide 

User Guide5
Assemble the Scanner
1. Remove all shipping tape from the top and bottom of the scanner. 
2. Peel off the protective plastic film from the control panel.
3. Open the automatic document feeder cover and remove any tape or protective foam from 
inside the feeder.  Close the feeder cover when you are finished.
4. Lift the scanner lid. 
5. Remove any tape and protective foam from around or on the flatbed glass.  

Xerox® DocuMate® 4830 Assemble the Scanner
6User Guide
6. Slide the locking tab to the unlocked position.
7. Close the scanner lid when you are finished.
Connect the Power Cord
Note: Only use the power supply (DA-48M24 made by APD) included with your scanner. 
Connecting any other type of power supply may damage your scanner, and will void its warranty.
1. Plug the power supply into the power port on the scanner.
2. Plug the power cord into the power supply and into a wall outlet. 

User Guide7
Installation
Please make sure of the following before you begin installation:
• If you are prompted to reboot during installation, please select "No". Finish installing the rest 
of the software, then close all open windows and reboot your computer. 
• The information in this guide may cover software not provided with the scanner you 
purchased. Please disregard any information about the software not applicable to your 
scanner.
• If your computer has AntiVirus or AntiSpyware software...

Xerox® DocuMate® 4830 Scanner Installation
8User Guide
Install the Software and Connect the 
Scanner
1. Start Microsoft Windows and make sure that no other applications are running.
2. Insert the installation disc into your computer’s DVD-ROM drive.
The disc automatically starts.
3. The Select Language window opens. Click the drop-down menu arrow and select the 
language to use. Click OK.
The disc’s Main menu window opens.
Note: If the disc does not start, check the following:
– Make sure the disc...

Installation Xerox® DocuMate® 4830 Scanner
User Guide9
4. On the Main menu, select Install software.
5. Make sure the boxes for Scanner Driver and Visioneer OneTouch are selected, as well as any 
other applications you want to install.
Note: The software provided with your scanner may differ slightly from the list shown in the 
window.
6. Click Install now. 

Xerox® DocuMate® 4830 Scanner Installation
10User Guide
Installing the Scanner Driver
The scanner driver installation will start first.
1. The Welcome screen for the scanner driver Setup Wizard opens. Click Next.
2. On the Xerox License Agreement window, read the license agreement. If you accept the 
terms, select I Agree then click Next. 
If you choose not to accept the license agreement, click Cancel. Click Close on the 
Installation Interrupted window.
3. The software will now be installed.
4.Stop...

Installation Xerox® DocuMate® 4830 Scanner
User Guide11
Connect the USB Cable and Turn on the Power
1. Remove any tape from the USB cable.
2. Plug the USB cable into the USB port on the scanner then into a USB port on the computer. 
Check your computer’s manual for USB port locations.
If the plug does not attach easily, make sure that you are plugging it in correctly. Do not force 
the plug into either connection.
3. Turn on the scanner power.
The status light comes on and flashes indicating that the...