Xerox Phaser 6120 User Manual

							Status, Error, and Service Messages 134
Web Links
Xerox provides several websites that offer additional help on your 
Phaser
 6120 printer. 
ResourceLink
Technical support information for 
your printer including online 
Technical Support, driver 
downloads, documentation, and 
much more:www.xerox.com/office/6120support
Supplies for your printer:www.xerox.com/office/6120supplies
A resource for tools and information, 
such as interactive tutorials, printing 
templates, helpful tips, and 
customized features to meet your 
individual needs:www.colorconnection.xerox.com
Local sales and support center:www.xerox.com/office/contacts
Printer registration:www.xerox.com/office/register
Material Safety Data Sheets 
(English only) identify materials, and 
provide information on safely 
handling and storing hazardous 
materials:www.xerox.com/office/msds
Information about recycling 
supplies:www.xerox.com/gwa
Downloaded From ManualsPrinter.com Manuals 
						

							Installing Options
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 136
Introduction
CAUTION
Use of non-Xerox supplies is not recommended. The Xerox Warranty, 
Service Agreements, and Total Satisfaction Guarantee do not cover damage, 
malfunction, or degradation of performance caused by use of non-Xerox 
supplies, or the use of Xerox supplies not specified for this printer. The Total 
Satisfaction Guarantee is available in the United States and Canada. 
Coverage may vary outside these areas; please contact your local 
representative for details. 
This chapter provides information about the following accessories.
Note:
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.
For details on the available options, contact your local reseller or 
refer to 
www.xerox.com/office/6120supplies.
Antistatic Protection
CAUTION
It’s very important to protect the printer controller board from electrostatic 
damage while performing any task involving the
 controller board.  
Turn off all power switches first. Discharge your body’s static electric charge 
by touching a grounded surface before you handle any printer boards or 
components. Also avoid walking around after grounding yourself.
Dual In-Line Memory Module 
(DIMM)128 MB DIMM 
Duplex UnitAuto duplexing
Tr a y  2500-sheet tray
Hard Drive20 GB Hard Drive
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 137
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex printing. 
A dual in-line memory module (or DIMM) is a compact circuit board with 
surface-mount memory chips.
Your printer comes with 128 MB SDRAM printer memory on board. However, 
you can upgrade to a maximum of 640 MB of RAM through the installation of 
an additional unbuffered SDRAM DIMM. Your printer comes with one free 
DIMM slot.
Installing a DIMM
CAUTION
It’s very important to protect the printer controller board and any associated 
circuit boards from electrostatic damage. Before performing this procedure, 
review the antistatic caution on 
Page 136. In addition, always handle circuit 
boards by the edges only.
1Turn off the printer and disconnect the power cord and interface cables.
If the duplex unit is installed, remove it.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 138
2Using a coin, remove the screw on the back of the printer.
3Remove the rear panel.
Since there are two hooks on the right side of the panel, remove 
the rear panel by gently pulling the left side of the panel toward 
you, then sliding the panel off to the left.
Downloaded From ManualsPrinter.com Manuals 
						

							Dual In-Line Memory Module (DIMM) 139
4Insert the new DIMM straight into the DIMM connector until the latches 
snap into the locked position.
Observe the keyed side of the DIMM to align it with the connector. If you 
cannot snap the DIMM into place, do not force it. Reposition it, making 
sure that the DIMM is seated completely in the connector.
5Reinstall the panel and tighten the screw.
If you removed the duplex unit in step 1, reinstall it.
6Reconnect all interface cables.
7Reconnect the power cord, and turn on the printer.
8Enable the memory in the driver. For instruction on enabling the memory, 
see 
“Selecting Driver Options/Defaults (for Windows)” on page 17.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Drive 140
Hard Drive
If a hard disk is installed, fonts can be downloaded and saved, and the 
overlay function can be used.
Installing a Hard Drive
CAUTION
It’s very important to protect the printer controller board and any associated 
circuit boards from electrostatic damage. Before performing this procedure, 
review the antistatic caution on 
Page 136. In addition, always handle circuit 
boards by the edges only.
1Turn off the printer and disconnect the power cord and interface cables.
If the duplex unit is installed, remove it.
2Using a coin, remove the screw on the back of the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Drive 141
3Remove the rear panel.
Since there are two hooks on the right side of the panel, remove 
the rear panel by gently pulling the left side of the panel toward 
you, then sliding the panel off to the left.
4Attach the mounting pin on the printer controller board.
Be sure to slide the tab on the hard disk mounting pin to the left 
during installation.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Drive 142
5Attach the spacer to the hard disk controller board.
Ensure that you have removed the plastic strip that covers the lithium 
battery.
 
6Attach the hard disk to the printer controller board.
7Reinstall the panel and tighten the screw.
If you removed the duplex unit in step 1, reinstall it.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Drive 143
8Reconnect all interface cables.
9Reconnect the power cord, and turn on the printer.
10Enable the hard disk in the driver. For instruction on enabling the hard 
disk, see 
“Selecting Driver Options/Defaults (for Windows)” on page 17.
Downloaded From ManualsPrinter.com Manuals