Xerox Phaser 7500DN User Manual

							Network Basics
Phaser 7500 Color Printer
User Guide41
7. Select the Advanced tab. Verify that the correct printer driver is installed.
8. Select the Ports tab. Verify that the IP Address in the Print to the Following Ports list is identical to 
the one on the Configuration page. You may need to click the Configure Port button to see the IP 
address. If necessary, re-select the TCP/IP number used for the printer.
Printing a Test Page
To print a test page:
1. Select the General tab.
2. Click Print Test Page. If the printer does not print, select PhaserSMART Technical Support on the 
Tro u b l e s h o o t i n g tab of your Windows printer driver to access PhaserSMART Technical Support.
See also: 
Online Support Assistant at www.xerox.com/office/7500support
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide 42
Macintosh OS X, Version 10.3 and Higher
This section includes:
•Macintosh OS X, Version 10.3 on page 42
•Macintosh OS X, Version 10.4 and Higher on page 43
•Macintosh Troubleshooting (Mac OS X, Version 10.3 and Higher) on page 44
Macintosh OS X, Version 10.3
Set up your printer using Bonjour (Rendezvous), create a desktop USB connection, or use an LPD/LPR 
connection for Macintosh OS X, version 10.3 and higher.
Bonjour (Rendezvous) Connection
To install the printer driver from the Software and Documentation CD-ROM:
1. Insert the CD-ROM into the CD-ROM drive and run the installer package to install the printer 
software.
2. When installation is complete, open the Printer Setup Utility. 
Note:To locate utilities on the Macintosh hard drive, open the Applications folder, and then open 
the Utilities folder. 
3. Confirm that the first drop-down menu is set to Bonjour (Rendezvous).
4. Select the printer in the window.
5. Select Xerox from the list of manufacturers in the lower drop-down menu.
6. Select the appropriate printer model from the list of available devices.
7. Click the Add button.
See also: 
Online Support Assistant at www.xerox.com/office/7500support
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide43
USB Connection
To install the printer driver from the Software and Documentation CD-ROM:
1. Insert the CD-ROM into the CD-ROM drive.
• Open the Printer Setup Utility. 
Note:To locate utilities on the Macintosh hard drive, open the Applications folder, and then open 
the Utilities folder. 
2. Click the Add button.
3. Select USB from the drop-down menu.
4. Select the printer in the window.
5. Select Xerox from the manufacturers in the drop-down menu.
6. Select the appropriate printer configuration from the list of available printers.
7. Click the Add button.
LPD/LPR Connection
To install the printer driver from the Software and Documentation CD-ROM:
1. Insert the CD-ROM into the CD-ROM drive and run the installer package to install the printer 
software.
2. Once installation is complete, open the Printer Setup Utility. 
Note:To locate utilities on the Macintosh hard drive, open the Applications folder, and then open 
the Utilities folder. 
3. Click the Add button.
4. Select IP Printing from the first pull-down menu. Select LPD/LPR from the second pull-down menu. 
Enter the printer’s IP address in the Printer Address field. Verify that the Queue Name field is 
blank. Select Xerox from the Printer Model pull-down menu, and then select the corresponding 
PPD file. Click the Add button. The printer is added to the list.
Macintosh OS X, Version 10.4 and Higher
To install the printer driver from the Software and Documentation CD-ROM:
1. Insert the CD-ROM into the CD-ROM drive. 
2. Run the installer package.
3. Follow the prompts in the Install Xerox Printer Installation dialog box.
If your printer does not appear in the list of discovered printers:
a. Click the IP Address or DNS Name button near the top of the window.
b. Type the address or name of the desired printer, and click Search.
c. When the printer is displayed in the window, click Continue.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide 44
Macintosh Troubleshooting (Mac OS X, Version 10.3 and Higher)
The following procedure eliminates cabling, communication, and connection problems. Once you 
complete these steps, print a test page from your software application. 
Mac OS X, Version 10.3 and Higher Troubleshooting
Perform these steps only for Mac OS X, versions 10.3 and higher:
1. Open the Network Utility, then click the Ping tab.
2. Enter the printer’s IP address.
3. Click Ping. If you do not get a response, confirm that your TCP/IP settings are correct for your 
printer and computer.
4. For AppleTalk, follow the steps below. For TCP /I P proceed to Step 5.
a. From the printer’s control panel, verify that EtherTalk is enabled. If it is not, enable it in the 
control panel, and then reset the printer.
b. Print the Configuration page and verify that EtherTalk is enabled.
c. From the Configuration page, verify the Zone. If you have multiple zones on your network, 
verify that your printer appears in the desired zone.
5. If you are still unable to print, access PhaserSMART Technical Support through CentreWare IS:
a. Launch your Web browser.
b. Enter the printer’s IP address in the browser’s Address field. 
c. Select Support. 
d. Click the PhaserSMART Diagnostic Tool link to access PhaserSMART.
See also: 
Online Support Assistant at www.xerox.com/office/7500support
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide45
UNIX (Linux)
Your printer supports connection to a variety of UNIX platforms through the network interface. The 
workstations currently supported by CentreWare for UNIX/Linux to a network-connected printer are:
•Sun Solaris
•IBM AIX
• Hewlett-Packard HP-UX
• Linux (i386)
• Linux (PPC)
The following procedures enable you to connect your printer using any of the supported versions of 
UNIX or Linux listed above.
Quick Install Steps
Perform the following procedures to set up the printer and install the appropriate drivers.
From the Printer
To set up the printer:
1. Verify that both TCP/IP protocol and the proper connector are enabled.
2. On the control panel, select one of these IP address options:
• Allow the printer to set up a DHCP address.
• Enter the IP address manually.
3. Print the Configuration page and keep it for reference.
From Your Computer
 To install the printer:
1. Go to www.xerox.com/office/7500drivers. 
2. Select Unix from the Operating System drop-down menu, and then click Go.
3. Click the CentreWare for Unix package for the operating system this will be installed in. This is the 
core package and must be installed first before the printer package.
4. Click the Start button to begin downloading.
5. Repeat steps 1 and 2, and then click the Printer Package for use with CentreWare for Unix link. 
6. Click the Start button to begin downloading.
7. In your browser, click the Installation Guide link, and then follow the installation instructions.
Note:If print-quality problems exist, or your job did not print, access PhaserSMART Technical 
Support through CentreWare IS.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide 46
To access PhaserSMART Technical Support:
1. Launch your Web browser.
2. Enter the printer’s IP address in the browser’s Address field.
3. Select Support.
4. Click the PhaserSMART Diagnostic Tool link to access PhaserSMART.
Installing the Printer When Using CUPS as the Print Spooler
When using CUPS as the print spooler, you need to add the printer’s .ppd file to the 
/usr/share/cups/model/Xerox directory. 
To install the .ppd file:
1. Go to www.xerox.com/office/7500drivers. 
2. Select Unix from the Operating System drop-down menu, and then click Go.
3. Click the PPD Files using CUPS Printing Services link.
4. Click the Start button to begin downloading.
5. In your browser, click the README link, and then follow the installation instructions.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide47
IPv6
This section includes:
•Enabling IPv6 on page 47
•Setting the Interface ID on page 48
•Automatic Address Assignment on page 49
•DHCPv6 on page 49
•Manual Address Assignment on page 50
•Address Precedence on page 51
Enabling IPv6
IPv6 can be enabled or disabled independently of IPv4.
Note:If you disable both IPv4 and IPv6, you will lose your connection to the printer. For 
information on restoring the default TCP/IP settings, see Resetting the TCP/IP Configuration on 
page 48.
To enable/disable IPv6, use one of the following options:
• The printer’s control panel
• CentreWare IS
Using the Control Panel
To enable/disable IPv6 on the control panel:
1. Select Printer Setup > Connection Setup > Network Setup > TCP /I P v6  S e tu p, then press the OK 
button.
2. Select IPv6, then press the OK button to switch between On and Off.
Using CentreWare IS
To enable/disable IPv6 using CentreWare IS:
1. Launch your Web browser.
2. Enter your printer’s IP address in the browser’s Address field.
3. Click Properties.
4. Select the Protocols folder on the left navigation panel, then click TC P / I P.
5. Click the TCP /I P  ( v 6) button.
6. Select the TCP /I P  v 6 En abl ed check box to enable TCP/IP v6.
7. Click the Save Changes button at the bottom of the page.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide 48
Resetting the TCP/IP Configuration
Use the following procedure at the control panel to reset the TCP/IP configuration to the default 
settings:
Select Printer Setup > Connection Setup > Reset Connection Setup, then press the OK button.
Setting the Interface ID
Your IPv6-enabled printer has one interface with multiple addresses. The Interface ID is the part of the 
address after the prefix. The printer uses the Interface ID when assigning both the Link-Local address 
and automatic addresses that use router supplied prefix(es). It is not used in addresses supplied by 
DHCPv6. Link-Local addresses are used by nodes to communicate with other nodes on the same local 
network. There are two options to set the Interface ID:
• The default is to have the Interface ID automatically computed from the MAC address associated 
with the interface. The ID is different for each device. This is the recommended method for setting 
the Interface ID.
• The other option is to manually set the interface ID. The Interface ID must be 64 bits (8 bytes) in 
length, and must not contain special characters other than colons or valid hexadecimal digits (0 
through 9, a through f, or A through F).
Note:If you change the Interface ID, you will be prompted to reset the printer before the changes 
take effect.
The Interface ID can only be set in CentreWare IS.
Using CentreWare IS
To set the Interface ID using CentreWare IS:
1. Launch your Web browser.
2. Enter your printer’s IP address in the browser’s Address field.
3. Click Properties.
4. Select the Protocols folder on the left navigation panel, then click TC P / I P.
5. Click the TCP /I P  ( v 6) button.
6. Do one of the following:
• Select User Interface ID from MAC address.
• Select Use this Interface ID.
7. Click the Save Changes button at the bottom of the page.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide49
Automatic Address Assignment
Addresses can be assigned automatically when a router is found that offers one or more prefixes. 
Automatically assigned addresses are routeable. Each router-supplied prefix is combined with the 
Interface ID to create an address. The use of router-supplied prefixes is enabled by default.
To enable/disable automatic address assignment, use one of the following options:
• The printer’s control panel
• CentreWare IS
Enabling/Disabling Automatic Address Assignment with the Control Panel
To set the Interface ID on the control panel:
1. Select Printer Setup > Connection Setup > Network Setup > TCP /I P v6  S e tu p, then press the OK 
button.
2. Select Auto Assign, then press the OK button to turn Auto Assign On or Off.
Enabling/Disabling Automatic Address Assignment with CentreWare IS
To set the Interface ID with CentreWare IS:
1. Launch your Web browser.
2. Enter your printer’s IP address in the browser’s Address field.
3. Click Properties.
4. Select the Protocols folder on the left navigation panel, then click TC P / I P.
5. Click the TCP /I P  ( v 6) button.
6. Select/deselect Use router supplied prefixes.
7. Click the Save Changes button at the bottom of the page.
DHCPv6
DHCPv6 is used to acquire TCP/IP information.
The following DHCPv6 options are available in CentreWare IS:
•As directed by the router - DHCPv6 is performed according to values in a router advertisement. 
This is the default setting.
•Always, for all configuration options (stateful) - Stateful DHCPv6 is always attempted, and router 
flags related to how to perform DHCP are ignored. Configuration options and an IPv6 address will 
be accepted if DHCPv6 is successful.
•Always, for all configuration options except address (stateless) - Stateless DHCPv6 is always 
attempted, and router flags related to how to perform DHCP will be ignored. Configuration options 
will be accepted if DHCPv6 is successful, but no IPv6 address will be assigned.
•Never - DHCPv6 is not used even if directed to do so by a router.
Downloaded From ManualsPrinter.com Manuals 
						

							Network Basics
Phaser 7500 Color Printer
User Guide 50
To enable/disable automatic address assignment, use one of the following options:
• The printer’s control panel
• CentreWare IS
Setting DHCPv6 Options with the Control Panel
To change DHCPv6 options using the control panel:
1. Select Printer Setup > Connection Setup > Network Setup > TCP /I P v6  S e tu p > DHCPv6 Mode, 
then press the OK button.
2. Select the DHCPv6 option, then press the OK button.
Setting DHCPv6 Options Using CentreWare IS
To change DHCPv6 options using CentreWare IS:
1. Launch your Web browser.
2. Enter your printer’s IP address in the browser’s Address field.
3. Click Properties.
4. Select the Protocols folder on the left navigation panel, then click TC P / I P.
5. Click the TCP /I P  ( v 6) button.
6. Select/deselect the DHCPv6 options.
7. Click the Save Changes button at the bottom of the page.
Manual Address Assignment
A manually entered IPv6 address is used in addition to any other IPv6 addresses. To create a manual 
address, enter the IPv6 address and prefix length in the fields provided in CentreWare IS. The default 
prefix length is 64.
To manually set the IPv6 address, use one of the following options:
• The printer’s control panel
• CentreWare IS
Setting the IPv6 Address with the Control Panel
To set the IPv6 address on the control panel:
1. Select Printer Setup > Connection Setup > Network Setup > TCP /I P v6  S e tu p, then press the OK 
button.
2. Select Manual Address, then press the OK button to turn manual addressing on.
3. Select Manual Address, then press the OK button.
4. To set the address:
a. Use the Up Arrow and Down Arrow buttons to set the first number, then press the OK button. 
b. Continue setting individual numbers, pressing the OK button after setting each one. When you 
get to the end of the address, press the OK button to return to the menu.
Downloaded From ManualsPrinter.com Manuals