Yamaha 01v 96 I Manual

Using the Solo Function51
01V96i—Reference Manual
Monitoring
Using the Solo Function
You can solo and monitor Input Channels, Aux Out 1–8, and 
Bus Out 1–8 using the [SOLO] buttons on the top panel.
1.Press the [DIO/SETUP] button repeatedly 
until the DIO/Setup | Monitor page appears.
2.Set the SOLO parameter to On.
Set other parameters on the page, if necessary.
3.To solo and monitor Input Channels, press 
the corresponding LAYER button to select a 
Layer that contains the desired channels, 
then press...

52Surround Pan
01V96i—Reference Manual
Surround Pan
This chapter describes surround panning, which determines 
how Input Channel signals are panned within and across the 
stereo field. 
About Surround Pan
The Surround Pan function places a sound image within a 
two-dimensional field using a multi-channel playback sys-
tem, and pans the image to the front, rear, left, and right in 
relation to the listening position. To pan the stereo image, you 
can use the Parameter wheel, or [INC]/[DEC] buttons.
If...

Setting Up and Selecting Surround Pan Modes53
01V96i—Reference Manual
Surround Pan
Setting Up and Selecting 
Surround Pan Modes
To configure the surround environment, select 3-1, 5.1, or 6.1 
Surround mode on the 01V96i and connect a DAW or 
multi-channel monitoring system to the 01V96i.
1.Press the DISPLAY ACCESS [PAN/ROUTING] 
button repeatedly until the Pan/Route | Surr 
Mode page appears.
1SURROUND MODE
This parameter enables you to select a Surround mode by 
using the following buttons. The button...

54Surround Pan
01V96i—Reference Manual
The DIO/Setup | Surr Bus page appears.
1BUS1–BUS8
These parameters select channels to be assigned to the 
Bus Outs in 3-1, 5.1, and 6.1 Surround modes.
2INIT
These buttons reset the channel assignment to the default 
setting.
3Surround LR to Stereo
When this check box is on, the left and right front signals 
of the surround channels are output from the STEREO 
L/R connectors.
7.To change the assignment, move the cursor 
to the desired Bus parameter, rotate the...

Setting Up and Selecting Surround Pan Modes55
01V96i—Reference Manual
Surround Pan■Surround Pan Monitoring
To monitor surround pan movement, patch the Bus Outs to the analog outputs, to which a monitoring system is connected.
The following diagram illustrates an example in which Bus Out 1/2 (left and right front channel) signals are output from the STE-
REO OUT L/R connectors and Bus Out 3–6 signals are output from the OMNI OUT 1–4 connectors in 5.1 Surround mode.
Tip: To output left and right front...

56Surround Pan
01V96i—Reference Manual
Surround Panning
You can set the surround pan parameters for each Input 
Channel.
1.Make sure that the 01V96i is in any Surround 
mode except Stereo, then press the [SEL] but-
ton of the channel for which you want to set 
surround pan.
2.Press the DISPLAY ACCESS [PAN/ROUTING] 
button repeatedly until the Pan/Route | Ch 
Edit page appears.
The Ch Edit page displays the selected Input Channel, 
and its surround pan setting and available pair partner.
The following...

Surround Panning57
01V96i—Reference Manual
Surround Pan3.Select one of seven trajectory patterns by 
turning on the corresponding trajectory pat-
tern button.
The following patterns are available:
• ......The sound image moves between left and right.
• ......The sound image moves between front and rear.
• ......The sound image moves from front left to rear 
right. With this pattern, you can also fine-tune 
the trajectory by using the WIDTH, DEPTH, 
OFFSET ( ), and OFFSET ( ) parameters.
• ......The sound...

58Surround Pan
01V96i—Reference Manual
7.To list multiple-channel surround pan set-
tings, press the [PAN/ROUTING] button 
repeatedly until the Pan/Route | Surr1-16, 
Surr17-32, or Surr ST IN page appears.
These pages display and enable you to edit the surround 
pan settings for 16 channels.
1Surround pan graphs
These graphs display the trajectory patterns and the cur-
rent pan positions for the Input Channels. 
2 parameter box
This parameter box enables you to move the surround 
pan setting of the...

Grouping Channels & Linking Parameters59
01V96i—Reference Manual
Grouping Channels & Linking Parameters
Grouping 
Channels & 
Linking 
Parameters
This chapter describes how to group faders or [ON] buttons 
for multiple channels and link the EQ or compressor param-
eters for simultaneous operation.
Grouping & Linking
On the 01V96i, you can group faders or [ON] buttons for 
multiple Input Channels (Input Channels 1–32, ST IN Chan-
nels 1–4) or multiple Output Channels (Bus Outs 1–8, Aux 
Outs 1–8, Stereo...

60Grouping Channels & Linking Parameters
01V96i—Reference Manual
•Out Mute page
This page enables you to set Mute groups (U–X) for Bus 
Outs (1–8), Aux Outs (1–8) and Stereo Out.
2.Press the up ( ) or down ( ) button to select 
a group.
3.Press the [SEL] button for a channel you wish 
to add to the group.
The selected channel is marked with “ ” and the chan-
nel is added to the group.
4.In the same way, press the [SEL] button for 
other channels you wish to add to the group.
The relative level of the...