Yamaha Fz 09 2014 Manual

Shifting mechanism 
Shift mechanism  type 
Shift fork guide  bar bending li mit 
Shift 
fork  thickness 
Air filter 
Air filter  element 
Fuel pump 
Pump  type 
Maximum  consumption  amperage 
Fuel injector 
Model/qua ntity 
Throttle body 
Type /quant ity 
ID mark 
Throttle position  sensor 
Resis ta nce 
Output  voltage ( at idle) 
Accelerator position  sensor 
Resistance 
O utput  voltage 
Air  induction  system 
Reed valve bending limit 
Soleno id 
res istance 
Idling condition 
Eng ine i dling speed...

EA$20300 
CHASSIS SPECIFICATIONS 
Chassis 
Frame type 
Caste r ang le 
T ra
il 
Front wheel 
Whee l type 
R im  s i
ze 
Rim  ma ter ial 
Whee l 
travel 
Rad ial  whee l run out  lim it 
La teral  wheel 
runo ut lim it 
Rear wheel 
Whee l type 
R im  siz e 
R im  ma ter ial 
Whee l 
travel 
Rad ial wheel  runout  limit 
Latera l w heel 
runo ut limi t 
Front tire 
Type 
Siz e 
Manu fa ctur er/mode l 
Manufacturer/mode l 
Wear  limi t (fro n
t) 
Rear tire 
Typ e 
Siz e 
Manufac turer/mode l...

Brake disc runout lim it (as  measured  on 
wheel) 
Brake 

pad 
lin ing thickness  (inner) 
Lim it 
Brake 

pad 
lin ing thickness  (outer) 
Lim it 
Master cylinder inside d iameter 
Caliper cyli nder ins ide  diameter 
Caliper cyli nder ins ide  diameter 
Spec ified brake 
fluid 
Rear bra ke 
Type 
Opera tion 
Rear  di
sc brake 
D i
sc outside  diameter  x th ickness 
Brake  disc thickness 
lim it 
Brake  disc runout lim it (as  measured  on 
wheel) 
Brake 

pad 
lin ing thickness  (inner) 
Lim it...

Rebound  dampi ng adjustin g pos iti ons 
M ini m um 
Standa rd 
Maximum 
Rear  su spe nsio n 
Type 
Spring/s hock  absorber  type 
Rear  shock  absor
ber assemb ly travel 
Spr ing  free length 
Spr ing installed  length 
Spr ing  rate  K 1 
Spr ing  stroke  K 1 
Enc losed gas/air  pressure  (STD) 
Spring 
pre load ad just ing  pos itions 
M ini
mum 
Standard 
Maxi m um 
Rebo und  dampi ng 
adjusting  positi ons 
M ini
mum 
Standard 
Maxim um 
D riv e ch ain 
Type /man ufacturer 
Number of lin ks 
Drive...

EA$20310 
ELECTRICAL SPECIFICATIONS 
Voltage 
System voltage 
Ignition system 
Ign it ion system 
Ign it ion timing  (B.T.D.C.) 
Engine control unit 
Model/manu facturer 
Ignition coil 
Min imum  igniti on  spark  gap 
Pr i
mary coil res istance 
Secon dary coil res istance 
Lean angle sensor output voltage 
Less  th an 65 ° 
More than 65° 
AC magneto 
Standard outp ut 
Sta t
or coil resistance 
R
ectifie r/regulator 
Regu la tor type 
Regu la ted voltage (DC) 
Rec tifie r capacity 
Battery 
Model...

Electric starting system 
System type 
Starter motor 
Power output 
Armature 
coil res istance 
Brush 
overall le ngth 
Limi t 
Brush 
spri ng  force 
M ica  undercut  (depth) 
Starter relay 
Amperage 
Coil resistance 
Horn 
Horn type 
Qua ntity 
Maximum  amperage 
Coil resistance 
Turn signal/hazard relay 
Relay type 
Built-in,  self-canceling dev ice 
Oil level switch 
Oil  leve l switch resistance  (maximum leve l po­
si tion) 
Oil  level 

switch  resistance  (mini
mum level po­
sition) 
Fuel sender...

ELECTRICAL SPECIFICATIONS 
Spare fuse 2.0A 
2-12  

EA$20320 
TIGHTENING TORQUES 
EA$20331 
GENERAL TIGHTENING  TORQUE 
SPECIFICATIONS 
Th is  chart  specifies  tighten ing  torques  for stan ­
dard  fasteners  with  a  sta nda rd ISO t hread  pitc h . 
T igh te
ning  torq ue  spec if icat io ns  for spec ia l com ­
ponents  or assemb lies  are  provided  for each 
ch apter  of  th is 
man ual. To  avo id warp age , tight­
e n  mu lti- fastene r 
assemblies in a crisscross  pat­
te
rn and  prog ressive  stages un til th e  spec ified 
tighte
ning  torque...

TIGHTENING TORQUES 
EA$203-CO 
EN G IN E TIGHTE NING TORQUES 
Item Thread 
Qty  Tightening torque  Re
marks size 
Spark  plug  M10 3 13 Nm (1.3 m
·kg f, 9.4 f t ·lbl) 
Cy li nde r 
head bolt M9  B See TIP . --

TIGHTENING TORQUES 
Item Thread Q ty Tightening torque Rema rks size 
Th rott le  body  jo int c lamp sc rew  M5 
6 3.0 Nm (0.30 m·kgf , 2.2 ft·lbf) 
Air filter case  cover  screw  M5 10 1.6 Nm (0.16 m·kgf , 1.2 ft·lbf) 
A ir filt er case  jo in t  clamp  screw  M5 
3 2.B Nm (0.2B m·kgf, 2.0 ft·lbf) 
Fue l injecto r adapte r bolt  M6 2  12 Nm (1.2 m ·kgf, B .7 ft ·lbf) 
A ir filte r case bo lt M6 
3  7 
Nm  (0. 7 m·kgf, 5.1 ft-l bf) 
Exha ust pipe  nu t MB 6 20 Nm (2.0 m·kg f, 1 4 ft· lb f) 
M uffler...