Barco Hdx Series Installation Manual

							11. Lamp
11.9 LPS power
What is indicated ?
The current LPS power in watt is indicated as information.
Image 11-24
LPS power
R5905032 HDX SERIES 23/11/2011187 
						

							11. Lamp
11.10 Lamp identification
About
The lamp identification menu gives an overview of the most important parameters of the used lamp.
These parameters are:
• Serial number of the lamp
• Article number of the lamp
• Run time sincefirst start up of the lamp
• Remaining run time for a safe operation of the lamp
• Number of strikes since thefirst start up of the lamp
• Software version
These parameters are useful in case of a service request.
How to display
1. PressMenuto activate the menus and selectLamp→Identification.
Image 11-25
Main menu, lamp
Image 11-26
Lamp, identification
2. PressENTERto select.
Image 11-27
Lamp identification
188R5905032 HDX SERIES 23/11/2011 
						

							11. Lamp
11.11Z-axisadjustment
What can be done?
TheZ-Axismenu item gives the current light output of the projector (in percentage). This light output indication can be used to
readjust the lamp position in the lamp casing (also called Z-axis adjustment of the lamp). With higher run times, the light output
of the lamp will decrease, which results in a lower light output on the screen. This light output decrease can be compensated by
readjusting the position of the lamp. This realignment has to be done by a qualified service technician.
How to display the light output
1. PressMenuto activate the menus and selectLamp→Z-axis.
Image 11-28
Main menu, lamp
Image 11-29
Lamp, Z-axis
2. PressENTERto display the current light output.
Image 11-30
Current light output
R5905032 HDX SERIES 23/11/2011189 
						

							11. Lamp
190R5905032 HDX SERIES 23/11/2011 
						

							12. Alignment
12. ALIGNMENT
Overview
• Alignment menu overview
• Orientation
• Lens adjustment, zoom - focus
• Lens adjustment, shift
• Lens adjustment, mid position
• Home lens at startup
• Calibrate lens
• Warping
• Blanking adjustment
• Contrast-Intensity
• Gamma
• Internal patterns
• Color space
• Scenergix
R5905032 HDX SERIES 23/11/2011
191 
						

							12. Alignment
12.1 Alignment menu overview
Overview table
Level 1 Level 2 Level 3
Alignment
Orientation Front / Table
Front / Ceiling
Rear / Table
Rear / Ceiling
Auto Front
Auto Rear
Lens
Zoom / Focus
Shift
Mid Position
Home lens at startup
Calibrate lens
Warping
Status
Rotation
Keystone
Pin/Barrel
4 corners
Warpfile service
Reset
Blanking Top
Bottom
Left
Right
Contrast/Intensity Contrast enhancement
Intensity
Gamma
Internal Patterns
Color Space Status
Projector
EBU
SMPTE
Custom
ScenergiX Status
White level
Black level
ScenergiX pattern
Adjust lines
Reset
192
R5905032 HDX SERIES 23/11/2011 
						

							12. Alignment
12.2 Orientation
What can be done?
The way of physical installation of the projector can be defined to the projector.
The following installation are possible:
• front/table
• front/ceiling
• rear/table
• rear/ceiling
• auto front : automatic front, projector detects itself if it is ceiling or table mounted and projects always a readable image.
• auto rear : automatic rear, projector detects itself if it is ceiling or table mounted and projects always a readable image.
How to set the correct orientation
1. PressMenuto activate the menus and selectAlignment→Orientation.
Image 12-1
Main menu, alignment
Image 12-2
Alignment, orientation
2. Use the▲or▼key to select the desired orientation and pressENTERto activate.
Image 12-3
Orientation list
R5905032 HDX SERIES 23/11/2011193 
						

							12. Alignment
12.3 Lens adjustment, zoom - focus
Zoom/Focus adjustment
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-4
Main menu, alignment
Image 12-5
Alignment, lens
2. Use the▲or▼key to selectzoom/focusand pressENTERto activate.
Image 12-6
Lens, Zoom/Focus
3. Use the▲or▼key to zoom the lens.
Use the◄or►key to focus the lens.
PressENTERto switch to Lens shift adjustment.
Image 12-7
Zoom/Focus adjustment
194R5905032 HDX SERIES 23/11/2011 
						

							12. Alignment
12.4 Lens adjustment, shift
How to shift lens
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-8
Main menu, alignment
Image 12-9
Alignment, lens
2. Use the▲or▼key to selectShiftand pressENTERto activate.
Image 12-10
Lens, shift
3. Use the▲or▼key to shift the lens in vertical direction.
Use the◄or►key to shift the lens in horizontal direction.
PressENTERto switch to Zoom/Focus adjustment.
Image 12-11
Shift adjustment
R5905032 HDX SERIES 23/11/2011195 
						

							12. Alignment
12.5 Lens adjustment, mid position
Howtoreturntomidposition
1. PressMenuto activate the menus and selectAlignment→Lens.
Image 12-12
Main menu, alignment
Image 12-13
Alignment, lens
2. Use the▲or▼key to selectMid Positionand pressENTERto activate.
Image 12-14
Lens, mid position
Lens will be shifted horizontally and vertically to its mid position.
196
R5905032 HDX SERIES 23/11/2011