Barco Hdx Series Installation Manual

							14. Service
14.3.5 Notification
About notifications
Notifications are warnings and errors displayed on the local LCD or on the OSD since power on of the projector. Once powered off,
the notification logging is cleared.
How to display
1. PressMenuto activate the menus and selectService→Diagnosis→Notifications.
Image 14-25
Main menu, service
Image 14-26
Service, diagnosis
Image 14-27
Diagnosis, notifications
2. PressENTERto display the notification list.
R5905032 HDX SERIES 23/11/2011
287 
						

							14. Service
Image 14-28
Notification overview list
288R5905032 HDX SERIES 23/11/2011 
						

							14. Service
14.3.6 Tilt sensor
What is possible?
The built-in tilt sensor can be read out to see if the projector is used in an allowed position. The statusfield indicates whether the
rotation of the projector is normal or abnormal.
Using a projector with an abnormal rotation can severely damage the lamp.
How to check the tilt sensor
1. PressMenuto activate the menus and selectService→Diagnosis→Tilt sensor.
Image 14-29
Main menu, service
Image 14-30
Service, diagnosis
Image 14-31
Diagnosis, tilt sensor
2. PressENTERto read out the tilt sensor.
Image 14-32
Tilt sensor output
R5905032 HDX SERIES 23/11/2011289 
						

							14. Service
The rotation of the projector is visually displayed. Coordinates of the tilt sensor and the offset from the normal position are given
in the tilt sensor pane.
The status pane indicates if the projector is used with an allowed rotation.
290
R5905032 HDX SERIES 23/11/2011 
						

							14. Service
14.4 Internal Service Patterns
How to select
1. PressMenuto activate the menus and selectService→Internal Service Patterns.
Image 14-33
Main menu, service
Image 14-34
Service, Internal service patterns
Image 14-35
Internal service patterns, Pmp In
2. Use the▲or▼key to select the desired internal service pattern and pressENTERto open a selection menu.
PmpInpatterns
Image 14-36
Pmp In test patterns
To change the options for the selected pattern, use he►key to open these options. The number of options can change for the
different patterns.
R5905032 HDX SERIES 23/11/2011
291 
						

							14. Service
Image 14-37
Pmp In test pattern options
Use the▲or▼key to select an option and pressENTERto select. The checkbox in front of that item will be checked.
Osd patterns
Image 14-38
Internal service patterns, OSD
PressENTERto display the list of possible patterns.
Image 14-39
OSD Test patterns
Pmp out patterns
Image 14-40
Internal service patterns, Pmp Out
PressENTERto display the list of possible patterns.
292
R5905032 HDX SERIES 23/11/2011 
						

							14. Service
Image 14-41
Pmp out test patterns
To change the options for the selected pattern, use he►key to open these options. The numberof options can change for the
different patterns.
Image 14-42
Pmp out internal service test patterns options
Fib patterns
Image 14-43
Internal service patterns, Fib
PressENTERto display the list of possible patterns.
Image 14-44
Fib test patterns
R5905032 HDX SERIES 23/11/2011293 
						

							14. Service
14.5 Convergence
What can be done?
The convergence patterns can be used to check the convergence alignment of red, green and blue. If there is a misalignment of at
least one 1 pixel, an electronic realignment is possible.
Mechanical realignment of the convergence can only be done by a qualified service technician.
How to display the convergence settings
1. PressMenuto activate the menus and selectService→Convergence.
Image 14-45
Main menu, service
Image 14-46
Service, convergence
Image 14-47
Convergence pattern
2. Use the▲or▼key to select a pattern.
3. PressENTERto start the adjustment.
Image 14-48
Convergence adjustment
294R5905032 HDX SERIES 23/11/2011 
						

							14. Service
Image 14-49
4. Use the convergence adjustments buttons on the light processor to adjust the convergence.
Adjust until the crossing of the center Green (Red) convergence pattern coincide with the diagonal line of the center Blue con-
vergence pattern.
R5905032 HDX SERIES 23/11/2011
295 
						

							14. Service
14.6 Factory defaults
What can be done?
All settings of the projector will be set to the original factory settings. All user settings are erased with this operation.
How to return to the factory defaults
1. PressMenuto activate the menus and selectService→Factory defaults.
Image 14-50
Main menu, service
Image 14-51
Service, factory defaults
Image 14-52
Factory defaults, settings
By default the following settings are excluded
- IP address
- Serial settings
- DMX settings
- Electronic convergence
2. If you want to restore also one of the items in the list, check the check box in front of that item.
SelectYesto restore the factory settings.
SelectNoto stop the restore process.
296
R5905032 HDX SERIES 23/11/2011