Canon Pixma Mx922 User Guide

							Shipping the Bluetooth Unit
The Bluetooth unit may not be used in countries or regions other than the country or region where it was
purchased due to local laws and regulations. Please note that the use of the Bluetooth unit in such countries or regions may lead to penalties and that Canon should not be liable for such punishment.
 
						

							Preparation to Use the Bluetooth Unit
 Bluetooth Unit
 Attaching to and Removing from the Printer
 
						

							Bluetooth Unit
The Bluetooth Unit BU-30 (hereafter referred to as the Bluetooth unit) is an adaptor which can be used with
a Canon IJ printer with Bluetooth interface.
By attaching the Bluetooth unit to a Canon IJ printer with Bluetooth interface, wireless printing from a Bluetooth enabled device, such as a computer or mobile phone, is possible.
Note
Communication is possible in a range of up to about 33 ft. / 10 m depending on the conditions below.
Printing speed may vary depending on the following conditions:
Presence of obstacles between the communication equipment and radio wave conditions.
Presence of magnetic fields, static electricity or electromagnetic interference.
Software and operating system to be used.
Receiver sensitivity and antenna performance of the communication equipment.
 
						

							Attaching to and Removing from the Printer
Attaching the Bluetooth Unit to the Printer
Removing the Bluetooth Unit from the Printer
Attaching the Bluetooth Unit to the Printer
Attach the Bluetooth unit to the USB flash drive port of the printer in accordance with the following procedure.
Refer to Front View for the position of the USB flash drive port.
1.
Make sure that the printer is turned on.
Confirming that the Power Is On
2.
Insert the Bluetooth unit to the USB flash drive port of the printer.
Detach the cap from the Bluetooth unit. Store the cap in a safe location.
Note
When the Bluetooth unit is properly attached to the printer, the message is displayed on the
LCD.
Removing the Bluetooth Unit from the Printer Remove the Bluetooth unit from the USB flash drive port of the printer in accordance with the followingprocedure.
1.
Remove the Bluetooth unit from the USB flash drive port of the printer.
Important
 
						

							Make sure that the lamp on the Bluetooth unit is neither lit nor flashing before you remove the
Bluetooth unit.
Important
Store the Bluetooth unit with the cap attached.
 
						

							Printing Data via Bluetooth Communication
 Preparation
 Installing the MP Drivers
 Checking the Device Name of the Printer
 Registering the Printer
 Deleting the Printer
 
						

							PreparationIn order to print via Bluetooth communication with Windows, the following system requirements must besatisfied.
•
Computer
A computer in which an internal Bluetooth module is installed or a computer to which an optional
Bluetooth adapter (available from various manufacturers) is attached.
•
OS
Microsoft Windows 7 (Satisfying any one of the following conditions is needed)
•
Add a Bluetooth Device is displayed in Hardware and Sound under Control Panel
•
Bluetooth Stack for Windows by Toshiba Version 7.00.00 or later is installed
Microsoft Windows Vista (Satisfying any one of the following conditions is needed)
•
Bluetooth Devices is displayed in Hardware and Sound under Control Panel
•
Bluetooth Stack for Windows by Toshiba Version 5.10.04 or later is installed
Microsoft Windows XP (Satisfying any one of the following conditions is needed)
•
Windows XP SP2 or later is installed, and Bluetooth Devices is displayed in
Printers and Other Hardware under Control Panel
•
Bluetooth Stack for Windows by Toshiba Version 3.00.10 or later is installed
For more information about how to confirm the version of Bluetooth Stack for Windows by Toshiba,
see Check 2: Is unsupported Bluetooth driver used?.
In order to connect the Bluetooth unit and print via Bluetooth communication, the following steps are required.
1.
Check that the Bluetooth unit is properly attached to the printer.
See  Attaching to and Removing from the Printer .
2.
Install the MP Drivers.
See  Installing the MP Drivers .
3.
Check the device name of the printer using the LCD.
See  Checking the Device Name of the Printer .
4.
Register the printer for Bluetooth printing.
•
When using Windows 7, and when Add a Bluetooth Device is displayed in
Hardware and Sound under Control Panel
Authenticate the printer as a Bluetooth device on  Add a Bluetooth Device in Hardware and
Sound  under  Control Panel .
See  Registering the Printer .
•
When using Windows Vista, and when Bluetooth Devices is displayed in
Hardware and Sound under Control Panel
Authenticate the printer as a Bluetooth device on  Bluetooth Devices in Hardware and Sound
under  Control Panel .
See  Registering the Printer .
 
						

							•When using Windows XP SP2 or later, and when Bluetooth Devices is displayed
in Printers and Other Hardware under Control Panel
Authenticate the printer as a Bluetooth device on  Bluetooth Devices in Printers and Other
Hardware  under Control Panel .
See  Registering the Printer .•
The operations may vary depending on your operating program. In this case,
refer to your computers operation manual.
 
						

							Installing the MP Drivers
Note
If you use the printer connecting with a computer, the MP Drivers have already been installed. In this
case, move to the next step.
Checking the Device Name of the Printer
Before connecting the Bluetooth unit to the printer for wireless printing, install the MP Drivers to your computer.
If you reinstall the MP Drivers, reinstall the MP Drivers using the Setup CD-ROM.
 
						

							Checking the Device Name of the Printer
This section describes the procedures for checking the settings of the Bluetooth unit on the LCD of the printer in preparation for Bluetooth printing.
Canon IJ printers with the Bluetooth interface are divided into two types. One is equipped with a graphicLCD, and the other with a text LCD.
If you need more information about the Bluetooth settings, see  Setting Bluetooth Printing.
1.
Make sure that the printer is turned on.
Confirming that the Power Is On
2.
Attach the Bluetooth unit.
For information about how to attach the Bluetooth unit, see  Attaching to and Removing from the
Printer .
3.
Display the  Bluetooth settings  (Graphic LCD)/Bluetooth settings  (Text LCD)
screen on the LCD.
For information about how to display the  Bluetooth settings (Graphic LCD)/Bluetooth settings  (Text
LCD) screen, refer to Changing the Machine Settings on the LCD.
Graphic LCD
Text LCD
Note
If the  Bluetooth settings  (Graphic LCD)/Bluetooth settings  (Text LCD) screen is not displayed
on the LCD, the Bluetooth unit may not be attached correctly. Remove the Bluetooth unit from the printer and attach it once again.
For details, see  Attaching to and Removing from the Printer .
If the  Bluetooth settings  (Graphic LCD)/Bluetooth settings  (Text LCD) screen is not yet
displayed, the Bluetooth unit may be faulty. In this case, contact the service center.
4.
Select  Select device name  (Graphic LCD)/Device name (Text LCD).
The  Select device name  (Graphic LCD)/Device name (Text LCD) screen is displayed.