Canon Pixma Mx922 User Guide

							Printing begins.
Note
When you use a USB cable for printing, select Canon XXX Printer from Select Printer.
To cancel a print job in progress, use the  Stop button on the printer or click  Cancel Printing on
the printer status monitor. After printing is canceled, a sheet of paper may be ejected with no
printing results.
To display the printer status monitor, click Canon XXX Printer (Copy X) on the taskbar.
X is a device name or a digit. The number of digits may differ depending on the printer.
 
						

							Printing with Bluetooth Compliant Devices other than a
Computer
The LCD of the printer allows you to perform settings for printing using Bluetooth compliant devices other than a computer.
When you print with one of these devices, also refer to your devices instruction manual.
When printing from a computer, see  Printing with Computers.
Note
Mobile phones, PDAs and digital cameras supporting OPP (Object Push Profile) or BIP (Basic
Imaging Profile) can print photos. Depending on your device, you may not perform printing even if your device supports the profilesabove. For details of profiles, refer to your devices instruction manual.
1.
Make sure that the printer is turned on.
Confirming that the Power Is On
2.
Attach the Bluetooth unit.
For information about how to attach the Bluetooth unit, see  Attaching to and Removing from the
Printer .
3.
Load paper.
Loading Paper
4.
Display the  Mobile phone print settings  (Graphic LCD)/Mob. phone settings
(Text LCD) screen on the LCD and set the media type and the paper size.
For information about how to display the  Mobile phone print settings (Graphic LCD)/Mob. phone
settings  (Text LCD) screen, refer to Changing the Machine Settings on the LCD.
5.
Start printing from the Bluetooth compliant device.
When you select the device name, select the initial value of the printer Canon XXX-1 (where XXX is your printers name).
If you are required to input the passkey, input the initial value 0000.
You can change the device name of the printer or passkey on the  Bluetooth settings (Graphic LCD)/
Bluetooth settings  (Text LCD) screen on the LCD.
Setting Bluetooth Printing
 
						

							Bluetooth Settings
 Setting Bluetooth Printing
 Bluetooth settings Screen
 
						

							Setting Bluetooth Printing
1.
Make sure that the printer is turned on.
Confirming that the Power Is On
2.
Attach the Bluetooth unit.For information about how to attach the Bluetooth unit, see  Attaching to and Removing from the
Printer .
Note
When the Bluetooth unit is properly attached to the printer, the message is displayed on the
LCD.
3.
Display the  Bluetooth settings  (Graphic LCD)/Bluetooth settings  (Text LCD)
screen on the LCD.
For information about how to display the  Bluetooth settings (Graphic LCD)/Bluetooth settings  (Text
LCD) screen, refer to Changing the Machine Settings on the LCD.
4.
Select the contents which you want to set on the LCD.
Bluetooth settings Screen
Note
For information about how to set a media type and a paper size when printing from a mobile
phone, refer to Changing the Machine Settings on the LCD.
 
						

							Bluetooth settings Screen
•
Graphic LCD
•
Text LCD
1.
Select device name (Graphic LCD)/Device name (Text LCD)
Displays the device name of the printer to which the Bluetooth unit is attached.
Select device name  (Graphic LCD)/Device name (Text LCD) Screen
2.
Access refusal setting  (Graphic LCD)/Access refusal  (Text LCD)
Selecting  ON (Graphic LCD)/ ON (Text LCD) will disable searching of this printer by a Bluetooth-
compatible device.
Access refusal setting  (Graphic LCD)/Access refusal  (Text LCD) Screen
3.
Security settings  (Graphic LCD)/Security settings  (Text LCD)
Select  Enable  (Graphic LCD)/ Enable (Text LCD) and then specify the security mode to activate the
passkey set on the  Change passkey (Graphic LCD)/Passkey (Text LCD) screen.
Security settings  (Graphic LCD)/Security settings  (Text LCD) Screen
4.
Change passkey  (Graphic LCD)/Passkey (Text LCD)
You can change the passkey. The passkey refers to an identification number to be determined. It is used to prevent unwanted access from other Bluetooth devices. The initial value is set to 0000.
Change passkey  (Graphic LCD)/Passkey (Text LCD) Screen
Select device name (Graphic LCD)/Device name (Text LCD) Screen Allows you to set the device name of the printer on a Bluetooth device.
 
						

							In the example used for this explanation, the model name is set to MX520 series.
When a model other than MX520 series is used, whatever appears in place of MX520 becomes the model name use.
Ex:
When you select  MX520 series-2, the printer name displayed on the Bluetooth device is  Canon MX520
series-2 .
The initial value is set to  MX520 series-1.•
Graphic LCD
•
Text LCD
Access refusal setting (Graphic LCD)/Access refusal (Text LCD) Screen
When you search from a Bluetooth device, you can enable or disable the display of the printer name.
•
ON (Graphic LCD)/ON (Text LCD)
Disables searching from a Bluetooth device.
•
OFF (Graphic LCD)/OFF (Text LCD) (Default setting) Enables searching and printing from a Bluetooth device.
Security settings (Graphic LCD)/Security settings (Text LCD) Screen
•
Enable (Graphic LCD)/Enable (Text LCD)
Selecting  Enable (Graphic LCD)/ Enable (Text LCD) allows you to choose either of the security modes
below.
•
Mode 3(recommended)  (Graphic LCD)/Mode 3 (recommend)  (Text LCD)
This mode is activated on link level enforced security.
The passkey will be required when a Bluetooth device communicates with the printer. Normally select this mode.
•
Mode 2  (Graphic LCD)/ Mode 2 (Text LCD)
This mode is activated on service level enforced security. The passkey will be required when printing through the Bluetooth communication.
After setting the security mode, we recommend making a trial print through Bluetooth communication. If printing does not start, change the security mode and try again.
Setting a passkey will prevent unwanted access from other Bluetooth devices. You can change the
passkey on the  Change passkey  (Graphic LCD)/Passkey (Text LCD) screen.
•
Disable (Graphic LCD)/Disable (Text LCD) (Default setting)
When you register the printer, you are not required to input a passkey.
 
						

							Change passkey (Graphic LCD)/Passkey (Text LCD) Screen
When you select  Enable (Graphic LCD)/ Enable (Text LCD) on the  Security settings (Graphic LCD)/
Security settings  (Text LCD) screen, you are required to set a passkey to register the printer on other
Bluetooth devices.
After you change the passkey, you may be asked to input the passkey on the Bluetooth devices you were able to print from before the passkey was changed. In this case, input the new passkey.•
Graphic LCD
•
Text LCD
 
						

							Specifications
Communication
methodBluetooth v2.0Maximum Speed1.44 MbpsOutputBluetooth Power Class 2
Communication
distance
Line-of-sight distance: approx. 33 ft./10 m * * It may vary depending on factors including the presence of obstacles between communication equipment, radio wave conditions, the presence of magnetic fields
around microwave ovens and locations where electrostatic and radio interference
occur, the types of software and operating systems used, and receiver sensitivity
and antenna performance of communication equipment.
Profile
SPP (Serial Port Profile)
OPP (Object Push Profile)
BIP (Basic Imaging Profile)
HCRP (Hardcopy Cable Replacement Profile)
Compatible PCs
A computer in which an internal Bluetooth module is installed or a computer to
which an optional Bluetooth adapter (available from various manufacturers) is attached.
OS/Software:
Microsoft Windows 7 (Satisfying any one of the following conditions is needed)•
Add a Bluetooth Device  is displayed in Hardware and Sound  under Control
Panel
•
Bluetooth Stack for Windows by Toshiba Version 7.00.00 or later is installed
Microsoft Windows Vista (Satisfying any one of the following conditions is needed)
•
Bluetooth Devices  is displayed in Hardware and Sound  under Control
Panel
•
Bluetooth Stack for Windows by Toshiba Version 5.10.04 or later is installed
Microsoft Windows XP (Satisfying any one of the following conditions is needed)
•
Windows XP SP2 or later is installed, and  Bluetooth Devices is displayed in
Printers and Other Hardware  under Control Panel
•
Bluetooth Stack for Windows by Toshiba Version 3.00.10 or later is installed
Frequency band2.4 GHz band (2.400 GHz to 2.4835 GHz)Power supplySupplied from the USB flash drive port on the printer, DC 4.4 V to 5.25 VMaximum power
consumption500 mW (MAX)Operating
temperature5 to 35°C (41 to 95°F)Operating humidity10 to 90% RH (no condensation)Dimensions (Width x
Depth x Height)18.5 (W) x 47.5 (D) x 8.7 (H) mm (with cap attached)
0.73 (W) x 1.87 (D) x 0.35 (H) inchesWeightApprox. 7 g (0.25 oz) 
						

							Copying
 Making Copies  Basic
 Displaying the Preview Screen
  Setting Items
 Reducing or Enlarging a Copy
 Two-Sided Copying
 About Other Copy Functions
 Copying Two Pages to Fit onto a Single Page
 Copying Four Pages to Fit onto a Single Page
 Copying Thick Originals Such as Books
 Copying without Borders
 Collated Copying
 Copying Photos
 
						

							Making CopiesLoad the original to copy.
This section describes the procedure to copy with  Standard copy.
1.
Make sure that the machine is turned on.
Confirming that the Power Is On
2.
Press the COPY button.
The Copy standby screen is displayed.
3.
Load paper.
Loading Paper
4.
Load the original document on the platen glass or in the ADF.
Loading Originals
5.
Specify the settings as necessary.
1.
Number of copies
Specify by using the  + or  - button.
2.
Print settings
By pressing the right  Function button, the print settings screen is displayed.
On the print settings screen, you can change the settings of page size, media type, and print
quality and so on.
Setting Items
3.
Preview
By pressing the left  Function button, you can preview an image of the printout on the
preview screen.
Displaying the Preview Screen
6.
Press the  Color button for color copying, or the  Black button for black & white
copying.
The machine starts copying.
Remove the original on the platen glass or from the document output slot after copying is
complete.
Important
If you load the original on the platen glass, do not open the document cover or remove the
original while  Scanning document...  is displayed on the screen.