Epson AcuLaser 2600DN User Manual

							Using the Control Panel241
7
7
7
7
7
7
7
7
7
7
7
7
Confidential Job Menu
This menu allows you to print or delete print jobs stored in the 
printer’s Hard Disk Drive using the Confidential Job feature of 
the printer driver’s Reserve Job function. You need to enter the 
correct password to access this data. For instructions on using this 
menu, see  Using the Confidential Job Menu on page 279.
Parallel Menu
These settings control communication between the printer and 
the computer when using the parallel interface.
* After this item is changed, the setting value takes effect after a warm boot 
or after the power is turned on again. While it is reflected in the Status Sheet 
and EJL read-back, the actual change takes effect after a warm boot or 
after the power is turned on again.
Parallel I/F
Allows you to activate or deactivate the parallel interface.
Speed
Specifies the pulse width of the ACKNLG signal when receiving 
data in the Compatibility mode or Nibble mode. When Fast is 
selected, the pulse width is about 1 µs. When Normal is selected, 
the pulse width is about 10 µs.
Bi-D
Item Settings (default in bold)
Parallel I/F*On, Off
Speed*Fast, Normal
Bi-D* Nibble, ECP, Off
Buffer Size*Normal, Maximum, Minimum
 
						

							242Using the Control Panel Allows you to specify the bidirectional communication mode. 
When you select Off, bidirectional communication is disabled.
Buffer Size
Determines the amount of memory to be used for receiving data 
and printing data. If Maximum is selected, more memory is 
allocated for receiving data. If Minimum is selected, more memory 
is allocated for printing data.
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in  Reset Menu on page 239.
❏Resetting the printer erases all print jobs. Make sure the Ready 
light is not flashing when you reset the printer.
USB Menu
These settings control communication between the printer and 
the computer when using the USB interface.
 
						

							Using the Control Panel243
7
7
7
7
7
7
7
7
7
7
7
7
*1After this item is changed, the setting value takes effect after a warm boot 
or after the power is turned on again. While it is reflected in the Status Sheet 
and EJL read-back, the actual change takes effect after a warm boot or 
after the power is turned on again.
*2Displayed only when a USB external device with D4 support is connected. 
The USB Ext I/F Confg setting is set to No automatically when exiting the panel 
settings.
*3Displayed only when a USB external device with D4 support is connected 
and the USB Ext I/F Confg setting is set to Yes. The contents of the settings 
depend on the USB external device settings.
*4Displayed only when the Get IP Address setting is set to Auto. This setting 
cannot be changed.
*5When the Get IP Address setting is changed from Panel or PING to Auto, the 
panel setting values are saved. When Auto is changed to Panel or PING, the 
saved setting values are displayed. 192.168.192.168 if the settings are not 
made from the panel.
USB I/F
Allows you to activate or deactivate the USB interface.
Item  Settings (default in bold)
USB I/F
*1On, Off
USB Speed
*1HS, FS
USB ExtI/F Confg
*2No, Yes
Get IP Address
*3Panel, Auto, PING
IP Address
*3*4*50.0.0.0 to 255.255.255.255
Subnet Mask
*30.0.0.0 to 255.255.255.255
Gate Way
*30.0.0.0 to 255.255.255.255
NetWare
*3On, Off
AppleTalk
*3On, Off
MS Network
*3On, Off
Rendezvous
*3On, Off
USB Ext I/F Init
*3-
Buffer Size
*1Normal, Maximum, Minimum
 
						

							244Using the Control Panel USB SPEED
Allows you to select the operation mode of USB interface. 
Selecting HS is recommended. Select FS if HS does not work on 
your computer system. 
Buffer Size
Determines the amount of memory to be used for receiving data 
and printing data. If Maximum is selected, more memory is 
allocated for receiving data. If Minimum is selected, more memory 
is allocated for printing data.
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in  Reset Menu on page 239. 
❏Resetting the printer erases all print jobs. Make sure the Ready 
light is not flashing when you reset the printer.
Network Menu
See the Network Guide for each setting.
AUX Menu
See the Network Guide for each setting.
LJ4 Menu
These settings control the fonts and symbol sets when in the LJ4 
mode.
 
						

							Using the Control Panel245
7
7
7
7
7
7
7
7
7
7
7
7
*1Available only when the optional font ROM module is installed.
*2Depending on whether Letter (60) or A4 (64) paper has been selected. Item  Settings (default in bold)
Font SourceResident, Download, ROM A
*1
Font Number0 to 65535 (depending on your settings)
Pitch 0.44 ... 10.00 ... 99.99 cpi in 0.01-cpi increments
Height 4.00 ... 12.00 ... 999.75 pt in 0.25-pt increments
SymSetIBM-US, Roman-8, Roman-9, ECM94-1, 8859-2 
ISO, 8859-9 ISO, 8859-10ISO, 8859-15ISO, 
PcBlt775, IBM-DN, PcMultiling, PcE.Europe, 
PcTk437, PcEur858, Pc1004, WiAnsi, WiE.Europe, 
WiTurkish, WiBALT, DeskTop, PsText, VeInternati, 
VeUS, MsPublishin, Math-8, PsMath, VeMath, 
PiFont, Legal, UK, ANSI ASCII, Swedis2, Italian, 
Spanish, German, Norweg1, French2, Windows, 
McText, PcIcelandic, PcLt774, PcTurk1, 
PcPortugues, PcEt850, PcTurk2, PcCanFrench, 
PcSI437, PcNordic, 8859-3 ISO, 8859-4 ISO, 
WiBaltic, WiEstonian, WiLatvian, Mazowia, 
CodeMJK, BpBRASCII, BpAbicomp, PcGk437, 
PcGk851, PcGk869, 8859-7 ISO, WiGreek, 
Europe3, PcCy855, PcCy866, PcLt866, PcUkr866, 
PcLit771, 8859-5 ISO, WiCyrillic, Bulgarian, 
Hebrew7, 8859-8 ISO, Hebrew8, PcHe862, 
Arabic8, PcAr864, 8859-6 ISO, OCR A, OCR B, 
Pc866Cyr, Pc866Ukr, WinCyr, ISOCyr, Pc8Grk, 
Pc851Grk, WinGrk, ISOGrk, Greek8, Pc862Heb, 
Pc864Ara, HPWARA
Form 5 ... 60/64
*2 ... 128 lines
Source SymSet 0 ... 277 ... 3199
Dest SymSet 0 ... 277 ... 3199
CR FunctionCR, CR + LF
LF FunctionLF, CR + LF
Tray Assign 4, 4K, 5S
 
						

							246Using the Control Panel Note:
If you normally use the HP LaserJet 4 printer driver when printing, you 
should change settings using this driver whenever you can. Printer 
driver settings always override the LJ4 Menu options.
FontSource
Sets the default font source.
Font Number
Sets the default font number for the default font source. The 
available number depends on the settings you made.
Pitch
Specifies the default font pitch if the font is scalable and of 
fixed-pitch. You can select from 0.44 to 99.99 cpi (characters per 
inch), in 0.01-cpi increments. This item may not appear depending 
on the Font Source or Font Number settings.
Height
Specifies the default font height if the font is scalable and 
proportional. You can select from 4.00 to 999.75 points, in 
0.25-point increments. This item may not appear depending on 
the Font Source or Font Number settings.
SymSet
Selects the default symbol set. If the font you selected in Font 
Source and Font Number is not available in the new SymSet 
setting, the Font Source and the Font Number settings are 
automatically replaced with the default value, IBM-US.
Form
 
						

							Using the Control Panel247
7
7
7
7
7
7
7
7
7
7
7
7
Selects the number of lines for the selected paper size and 
orientation. This also causes a line spacing (VMI) change, and the 
new VMI value is stored in the printer. This means that later 
changes in the Page Size or Orientation settings cause changes in 
the Form value, based on the stored VMI.
Source SymSet, Dest SymSet
Available only in certain locations where printers are sold with a 
special ROM module installed to handle specific languages.
CR Function, LF Function
These functions are included for users of particular operating 
systems, such as UNIX.
Tray Assign
Changes the assignment for the paper source select command. 
When 4 is selected, the commands are set as compatible with the 
HP LaserJet 4. When 4K is selected, the commands are set as 
compatible with the HP LaserJet 4000, 5000, and 8000. When 5S is 
selected, the commands are set as compatible with the HP LaserJet 
5Si.
GL2 Menu
This menu lets you set the printer to emulate a plotter, allowing 
you to use software which requires a plotter for output. The 
LJ4GL2 mode is similar to the GL/2 mode supported in the HP 
LaserJet 4 mode. The GLlike mode emulates some of the HP-GL 
plotter commands and includes all the commands found in HP’s 
GL/2 mode, as well as two additional commands.
 
						

							248Using the Control Panel
* Available only when GLlike is selected as the GL Mode.
Before you start printing in the GL/2 mode
You may need to change the following print options in your 
application, depending on your output needs. Check these 
settings to make sure they match the data you are trying to print.
If you need to configure the printer settings, first switch to the 
GL/2 emulation mode, then change the settings using the printer 
driver, or the control panel menus.
Item Settings (default in bold)
GL ModeLJ4GL2, GLlike
ScaleOff, A0, A1, A2, A3
OriginCorner, Center
PenPen0, Pen1, Pen2*, Pen3*, Pen4*, Pen5*, 
Pen6*
EndButt, Square, Triangular, Round
JoinMitered, Miteredbeveled, Triangular, 
Round, Beveled, None
Pen 0 through 6 0.05 ... 0.35 ... 5.00 mm in 0.05-mm 
increments
Print Options Settings
Paper size Printer’s paper size setting
Driver (plotter 
selection)HP-GL/2 or HP-GL
Pen configuration Pen thickness
Plot origin Center or Corner
OrientationGLlike offers landscape only LJ4GL2 offers 
landscape and portrait
 
						

							Using the Control Panel249
7
7
7
7
7
7
7
7
7
7
7
7
Note:
Settings or data saved in the printer’s RAM (such as downloaded fonts) 
may be erased when you change the emulation mode.
GL Mode
Specifies whether the printer uses a direct emulation of the GL/2 
plotter language, or the HP LaserJet 4 emulation of GL/2.
Scale
Specifies whether the output from the software is scaled. The scale 
factor is based on the output paper size of the application.
Origin
Specifies whether the logical origin of the “plotter” is the corner 
or the center of the paper.
Pen
Allows you to choose a pen which you can then set the thickness 
for in the Pen 0 through 6 item. The LJ4GL2 mode supports two 
pens (0 and 1), while the GLlike mode supports seven pens (0 
through 6).
End
Specifies the way in which lines end.
Join
Specifies the way in which lines are joined.
Pens 0 through 6
Allows you to set the thickness of the pens used to make the 
printout. Pen 0 and Pen 1 are available in the LJ4GL2 mode, and 
Pen 0 through Pen 6 are available in the GLlike mode.
 
						

							250Using the Control Panel
PS3 Menu
These settings are available in the PS3 mode.
* Available only in the color mode.
Error Sheet
When you select On, the printer prints out an error sheet.
Coloration
Allows you to select the color printing mode or monochrome 
printing mode.
Image Protect
The printer employs lossy compression when Off is selected. The 
printer does not employ lossy compression when On is selected. 
Lossy compression refers to a data compression technique in 
which some amount of data is lost.
ESCP2 Menu
This menu allows you to make settings which affect the printer 
when it is in the ESC/P 2 emulation mode.
Item Settings (default in bold)
Error SheetOff, On
Coloration*Color, Mono
Image ProtectOff, On