Epson AcuLaser 2600DN User Manual

							Cleaning and Transporting the Printer341
10
10
10
10
10
10
10
10
10
10
10
10
❏Loaded paper
❏Toner Cartridge
❏Photoconductor unit
❏Installed options
c
Caution:
Before handling the photoconductor unit, be sure to confirm 
the handling precautions. See  Handling precautions on 
page 319 for instructions.
2. Attach the protective materials onto the printer, then repack 
the printer in its original box.
For short distances
Always pay attention to the following handling precautions when 
you need to move the printer for short distances.
If you are moving the printer on its own, two people should lift 
and carry the printer.
Follow the steps below to move the printer for short distances. 
1. Turn off the printer and remove the following items:
❏Power cord
❏Interface cable
❏Loaded Paper
❏Toner Cartridge
❏Photoconductor unit
 
						

							342Cleaning and Transporting the Printer❏Installed options
c
Caution:
Before handling the photoconductor unit, be sure to confirm 
the handling precautions. See  Handling precautions on 
page 319 for instructions.
2. Be sure to lift the printer by the correct positions as shown 
below.
* Do not lift the printer by these areas.
3. When moving the printer, always keep it horizontal.
*
 
						

							Cleaning and Transporting the Printer343
10
10
10
10
10
10
10
10
10
10
10
10
Finding a place for the printer
When relocating the printer, always choose a location that has 
adequate space for easy operation and maintenance. Use the 
following illustration as a guide for the amount of space required 
around the printer to ensure smooth operation. Dimensions 
shown in the illustrations below are in centimeters.
To install and use any of the following options, you will need the 
indicated amount of additional space.
The optional paper cassette unit adds 115 mm (4.5 in.) to the 
bottom of the printer. 
In addition to space considerations, always heed the following 
precautions when finding a place to locate the printer:
100 mm
100 mm430 mm
330 mm
130 mm
 
						

							344Cleaning and Transporting the Printer ❏Place the printer where you can easily unplug the power cord.
❏Keep the entire computer and printer system away from 
potential sources of interference, such as loudspeakers or the 
base units of cordless telephones.
❏Avoid using an electrical outlet that is controlled by wall 
switches or automatic timers. Accidental disruption of power 
can erase valuable information in your computer’s and 
printer’s memory.
c
Caution:
❏Leave adequate room around the printer to allow for sufficient 
ventilation.
❏Avoid locations that are subject to direct sunlight, excessive 
heat, moisture, or dust.
❏Avoid using outlets that other appliances are plugged into.
❏Use a grounded outlet that matches the printer’s power plug. 
Do not use an adapter plug.
❏Only use an outlet that meets the power requirements for this 
printer.
 
						

							Troubleshooting345
11
11
11
11
11
11
11
11
11
11
11
11
Chapter 11 
Troubleshooting
Clearing Jammed Paper
If paper becomes jammed in the printer, the printer’s LCD panel 
and EPSON Status Monitor 3 provide alert messages.
Precautions for clearing jammed paper
Be sure to observe the following points when you clear jammed 
paper.
❏Do not remove jammed paper by force. Torn paper can be 
difficult to remove and might cause other paper jams. Pull it 
gently in order to avoid tearing.
❏Always try to remove jammed paper with both hands to avoid 
tearing it.
❏If jammed paper is torn and remains in the printer, or if paper 
is jammed in a place not mentioned in this chapter, contact 
your dealer.
❏Make sure that the paper type that is loaded is the same as the 
Paper Type setting in the printer driver.
 
						

							346Troubleshooting
w
Warning:
❏Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot.
❏Do not insert your hand deep into the fuser unit as some 
components are sharp and may cause injury.
Jam A (cover A)
Follow the steps below to clear paper jams at cover A.
1. Remove all paper that is loaded on the MP tray.
 
						

							Troubleshooting347
11
11
11
11
11
11
11
11
11
11
11
11
2. Close the MP tray.
Note:
Close the expansion trays, if needed, before closing the MP tray.
3. Push the latch on cover A to the left and open the cover until 
it stops.
 
						

							348Troubleshooting 4. If the optional Duplex Unit is not installed, gently pull out any 
sheets of paper. Be careful not to tear the jammed paper.
If the optional Duplex Unit is installed, lift up the Duplex Unit. 
Hold it and gently pull out any sheets of paper. Be careful not 
to tear the jammed paper.
w
Warning:
Be careful not to touch the fuser, which is marked CAUTION 
HIGH TEMPERATURE, or the surrounding areas. If the 
printer has been in use, the fuser and the surrounding areas 
may be very hot. If you must touch one of these areas, open 
cover A and B, then wait 30 minutes to allow the heat to 
subside before doing so.
 
						

							Troubleshooting349
11
11
11
11
11
11
11
11
11
11
11
11
5. Close cover A. Then open the MP tray and reload the paper.
Jam A, B (cover A and B)
Follow the steps below to clear paper jams at cover A and B.
1. Remove all paper that is loaded on the MP tray. 
2. Close the MP tray.
Note:
Close the expansion trays, if needed, before closing the MP tray.
 
						

							350Troubleshooting 3. Push the latch on cover A to the left and open the cover until 
it stops.
4. If the optional Duplex Unit is not installed, gently pull out any 
sheets of paper. Be careful not to tear the jammed paper.