Epson AcuLaser 2600DN User Manual

							Using the Control Panel261
7
7
7
7
7
7
7
7
7
7
7
7
Adjust the density of the printing for back side of normal paper. 
The setting becomes darker as the value increases.
Thick
Adjust the density for thick paper. The setting becomes darker as 
the value increases.
Trnsprnc
Adjust the density for transparencies. The setting becomes darker 
as the value increases.
Envelope
Adjust the density for envelopes. The setting becomes darker as 
the value increases.
Highland
Prevents printing defects caused by abnormal electric discharge 
that may occur when using the printer in locations at high 
altitudes. Select 1 when using the printer in locations at high 
altitudes.
Feed Offset
Adjust the vertical position in which to start printing. The position 
moves lower on the sheet as the value increases. This setting is 
used when doing single-sided printing or printing the first page 
for duplex printing.
Scan Offset
Adjust the horizontal position in which to start printing. The 
position moves to the right of the sheet as the value increases. This 
setting is used when doing single-sided printing or printing the 
first page for duplex printing.
 
						

							262Using the Control Panel Feed Offset2
Adjust the vertical position in which to star printing. The position 
moves lower on the sheet as the value increases. This setting is 
used when printing the printing on the backside of paper for 
duplex printing.
Scan Offset2
Adjust the horizontal position in which to start printing. The 
position moves to the right of the sheet as the value increases. This 
setting is used when printing on the backside of paper for duplex 
printing.
Status and Error Messages
This section contains a list of error messages shown on the LCD 
panel, giving a brief description of each message and suggestions 
for correcting the problem. Note that not every message shown 
on the LCD panel indicates a problem. When the   mark is 
displayed at the left of the warning message, multiple warnings 
occur. To confirm all warnings that occur, press the dDown 
button to display the Status Menu, then press the Enter button. 
The LCD panel also displays the amounts of remaining toners and 
available paper sizes.
Calibrating Printer
The printer automatically calibrates itself. This is not an error 
message, and will clear itself after the calibration process has 
finished. While the printer displays this message, do not open the 
covers or turn off the printer.
Cancel All Print Job
 
						

							Using the Control Panel263
7
7
7
7
7
7
7
7
7
7
7
7
The printer is canceling all print jobs in the printer memory, 
including jobs the printer is currently receiving or printing. This 
message appears when the +Cancel Job button has been 
pressed down for more than 2 seconds.
Cancel Print Job
The printer is canceling the current print job. This message 
appears when the +Cancel Job button has been pressed and 
released within 2 seconds.
Cancel Print Job (by host)
The print job is canceled at the printer driver.
Can’t Print
The print data is deleted because it is incorrect.
Make sure that the appropriate paper size is set and appropriate 
your printer driver is used.
Can’t Print Duplex
The printer has encountered problems during duplex printing. 
Make sure you are using an appropriate type and size of paper 
for the Duplex Unit. The problem could also be a result of 
incorrect settings for the paper source you are using. Pressing the 
NStart/Stop button will print the rest of the print job on only one 
side of the paper. Press the +Cancel Job button to cancel the 
print job.
Change Toner to X
This message appears when the printer switches from the 4 × 
B/W mode to Color 4 mode. (The letter C, M, or Y appears in place 
of X and indicates the colors Cyan, Magenta, or Yellow 
respectively.) See  Switching the Printing Mode on page 283 to 
find how to switch the mode.
 
						

							264Using the Control Panel Check Paper Size
The paper size setting is different from the size of paper loaded 
in the printer. Check to see if the correct size of paper is loaded in 
the specified paper source.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. See  How to access the control panel menus on page 
223 for instructions.
Check Paper Type
The media loaded in the printer does not match the paper type 
setting in the printer driver. Media that matches only the paper 
size setting will be used for printing.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. See  How to access the control panel menus on page 
223 for instructions.
Clean Parts v v
Indicates that the printer needs to be cleaned using the cleaning 
knob [a] or [b] (indicated as vv). See  Cleaning the 
photoconductor wire (knob [a]) on page 338 or  Cleaning the 
exposure window (knob [b]) on page 339 for instructions.
Clean Sensor
The sensor inside the printer needs to be cleaned. To clean the 
sensor, open cover D and close it again. 
Collate Disabled
Printing by specifying the number of copies is no longer possible 
due to a lack of memory (RAM) or free disk space on the optional 
Hard Disk Drive. If this error occurs, print only one copy at a time.
 
						

							Using the Control Panel265
7
7
7
7
7
7
7
7
7
7
7
7
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
Color Data Received
The printer receives color printing data when it is in the B/W or 
4 × B/W mode. Press the NStart/Stop button to print the data in 
monochrome, or press the +Cancel Job button to cancel the 
print job.
Cooling Down
The printer lowers its temperature to optimize for the fixing toner. 
Wait for a moment for Ready to appear in the LCD panel.
Duplex Memory Overflow
There is not enough memory for duplex printing. The printer 
prints only on the front and ejects the paper. To clear this error, 
follow the instructions below.
If Off is selected as the Auto Cont setting on the control panel’s 
Setup Menu, press the NStart/Stop button to print on the back 
of the next sheet, or press the +Cancel Job button to cancel the 
print job.
If On is selected as the Auto Cont setting on the control panel’s 
Setup Menu, printing continues automatically after a certain 
period of time.
Formatting HDD
The Hard Disk Drive is being formatted.
Form Data Canceled
 
						

							266Using the Control Panel Unable to store form overlay data on the printer’s optional Hard 
Disk Drive. Either the drive is full, or the maximum number of 
form overlay files has been reached. Delete any form overlay files 
you no longer need, then try storing the new overlay again.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
Form Feed
The printer is ejecting paper due to a user request. This message 
appears when pressing the NStart/Stop b u t t on  o n ce  t o m a k e t he  
printer offline, then holding down the NStart/Stop button for 
more than 2 seconds in order not to receive form feed command.
Format Error ROM A
An unformatted ROM module has been inserted. 
To clear this error, either press the NStart/Stop button or turn off 
the printer and remove the ROM module, then reinstall the ROM 
module. If that fails to clear the error, contact your dealer.
Hard Disk Full
The optional Hard Disk Drive is full and you cannot save any 
data. Delete the unnecessary data from the Hard Disk Drive. To 
clear this error, select Clear Warning from the control panel’s 
Reset Menu. For instruction about accessing the control panel 
menus, see  How to access the control panel menus on page 223.
HDD CHECK
The printer is checking the Hard Disk Drive.
Image Optimum
 
						

							Using the Control Panel267
7
7
7
7
7
7
7
7
7
7
7
7
There is insufficient memory to print the page at the specified 
print quality. The printer automatically lowers the print quality 
s o  t h a t  i t  c a n  c o n t i n u e  p r i n t i n g .  I f  t h e  q u a l i t y  o f  t h e  p r i n t o u t  i s  n o t  
acceptable, try simplifying the page by limiting the number of 
graphics or reducing the number and size of fonts.
To clear this error, select Clear Warning from the control panel’s 
Reset Menu. See  How to access the control panel menus on page 
223 for instructions.
Turn the Image Optimum setting off on the control panel’s Printing 
Menu if you do not want the printer to automatically lower the 
print quality to continue printing.
You may need to increase the amount of printer memory to be 
able to print at the desired print quality for your document. For 
more information on adding memory, see  Memory Module on 
page 303.
Install Fuser
There is no fuser unit installed or the fuser unit is not installed 
properly. Turn off the printer, then install the fuser unit if it is not 
installed. 
If a fuser unit is already installed, turn the printer off and reinstall 
the unit after it has cooled off (30 minutes). Open covers A and B. 
Remove the fuser unit, then reinstall it properly. Close covers A 
and B. The error clears automatically if the fuser unit is properly 
installed. 
If the error is not cleared, the fuser unit is out of order. Replace it 
with a new fuser unit.
Install Photoconductor
There is no photoconductor unit installed or the photoconductor 
unit is not installed properly. Turn off the printer and install the 
photoconductor unit if it is not installed.
 
						

							268Using the Control Panel If a photoconductor unit is already installed, confirm cover D is 
closed. Otherwise, turn off the printer, open cover D. Remove the 
photoconductor unit, then reinstall it properly. Close cover D. The 
error clears automatically if the photoconductor unit is properly 
installed. 
Install uuuu TnrCart
The indicated toner cartridges are not installed in the printer. (The 
letters C, M, Y, or K appear in place of uuuu and indicate the colors 
Cyan, Magenta, Yellow, and Black respectively.)
Install the indicated cartridges. See  Toner Cartridge on page 
315.
Install Waste T Box
The waste toner collector is not installed, or is installed 
incorrectly. If there is no waste toner collector installed, install one 
in the printer. If there is a waste toner collector already installed, 
try removing it and reinstalling it. See  Waste Toner Collector 
on page 331 for instructions.
Invalid AUX I/F Card
This message means that the printer cannot communicate with 
the installed optional interface card. Turn off the printer, remove 
the card, then reinstall it.
Invalid Data
The spool file on the driver is deleted while printing or the data 
is abnormal. Press the NStart/Stop button to clear the error.
Invalid HDD
Either the optional Hard Disk Drive is damaged or it cannot be 
used with this printer. Turn off the printer, then remove the Hard 
Disk Drive.
 
						

							Using the Control Panel269
7
7
7
7
7
7
7
7
7
7
7
7
Invalid N/W Module
There is no network program, or the network program cannot be 
used with your printer. Contact a qualified service representative.
Invalid P5C
The optional P5C Emulation Kit is installed, but the printer is in 
the B/W mode or 4 × B/W mode. When you use the optional P5C 
Emulation Kit, make sure that the printer is in the Color mode. 
Invalid PS3
The PostScript3 ROM module is broken. Turn off the printer and 
contact your dealer.
Invalid ROM A
The printer cannot read the installed optional ROM module. Turn 
off the printer, then remove the ROM module.
Jam-Paper Size Error
A paper jam occurred because the wrong size paper has been 
loaded. Clear the jammed paper and set the paper size setting 
correctly. See  Clearing Jammed Paper on page 345 to find how 
to clear the jammed paper.
Manual Feed ssss
The manual feed mode is specified for the current print job. Make 
sure the paper size indicated by ssss is loaded, then press the 
NStart/Stop button.
Mem Overflow
The printer has insufficient memory to execute the current task. 
Press the NStart/Stop button on the control panel to resume 
printing, or press the +Cancel Job button to cancel the print job.
 
						

							270Using the Control Panel Menus Locked
This message appears if you try to change the printer’s settings 
through the control panel when the buttons are locked. You can 
unlock them by using the Network utility. Refer to the Network 
Guide for information.
Need Memory
The printer has insufficient memory to complete the current print 
job. 
To clear this error message, select Clear Warning from the control 
panel’s Reset Menu. See How to access the control panel menus 
on page 223 for instructions.
To prevent this problem from happening again, add more 
memory to your printer as described in  Memory modules on 
page 414, or reduce the resolution of the image to be printed.
NonGenuine Toner Cartridge
The installed toner cartridge is not a genuine Epson product. 
Installing a genuine toner cartridge is recommended. Using a 
non-genuine toner cartridge may affect print quality. Epson shall 
not be liable for any damages or problems arising from the use of 
consumable products not manufactured or approved by Epson.
Install a genuine Epson product, or Clear All Warnings of the 
Reset Menu on the control panel to clear the warning message. 
See  Toner Cartridge on page 315 for instructions on replacing 
the imaging cartridge.
NonGenuine Toner uuuu