Epson AcuLaser 2600DN User Manual

							Installing Options291
8
8
8
8
8
8
8
8
8
8
8
8
w
Warning:
Two people should lift the printer by the correct positions.
4. Open cover E.
 
						

							292Installing Options 5. Fasten the optional paper cassette unit to the printer with the 
provided plates and screws.
6. Close cover E.
7. Secure the unit to the left side of the printer with the remaining 
plate and screw.
 
						

							Installing Options293
8
8
8
8
8
8
8
8
8
8
8
8
8. Reconnect the interface cable and power cord, then turn the 
printer on.
To confirm that the option is installed correctly, print a Status 
Sheet. See  Printing a Status Sheet on page 370.
Note for Windows users:
If EPSON Status Monitor 3 is not installed, you have to make settings 
manually in the printer driver. See  Making Optional Settings on page 
98.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete 
the printer using Print Setup Utility (for Mac OS X 10.3), Print 
Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), 
and then re-register the printer.
Removing the optional paper cassette unit
Turn off the printer and perform the installation procedure in 
reverse.
Duplex Unit
For specifications or details about the paper types and sizes that 
you can use with the Duplex Unit, see  Duplex Unit on page 414.
Installing the Duplex Unit
Follow the steps below to install the optional Duplex Unit.
1. Turn the printer off and unplug the power cord and interface 
cable.
 
						

							294Installing Options 2. Open the MP tray.
3. Push the latch on cover A to the left and open the cover.
 
						

							Installing Options295
8
8
8
8
8
8
8
8
8
8
8
8
4. Remove the two screws securing the cover MP.
5. Remove the cover MP from cover A.
6. Take the Duplex Unit out of its package.
 
						

							296Installing Options 7. Fit the hooks on cover A into the notches on the Duplex Unit.
 
						

							Installing Options297
8
8
8
8
8
8
8
8
8
8
8
8
8. Pull the upper part of the Duplex Unit upward and secure the 
Duplex Unit to the printer with the two provided screws.
9. Close cover A and the MP tray.
To confirm that the option is installed correctly, print a Status 
Sheet. See  Printing a Status Sheet on page 370.
Note for Windows users:
If EPSON Status Monitor 3 is not installed, you have to make settings 
manually in the printer driver. See  Making Optional Settings on page 
98.
Note for Macintosh users:
When you have attached or removed printer options, you need to delete 
the printer using Print Setup Utility (for Mac OS X 10.3), Print 
Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), 
and then re-register the printer.
 
						

							298Installing Options For Windows, see  Printing with the Duplex Unit on page 94, 
For Macintosh, see  Printing with the Duplex Unit on page 171 
for information about duplex printing.
Removing the Duplex Unit
Turn off the printer and perform the installation procedure in 
reverse.
Hard Disk Drive
The optional Hard Disk Drive allows you to expand the printer’s 
input buffer when the Ethernet interface is used, and gives you 
additional memory for graphics, form data, and faster multi-page, 
multi-output sorting.
Installing the Hard Disk Drive
Follow the steps below to install the Hard Disk Drive.
c
Caution:
Before you install the Hard Disk Drive, be sure to discharge any 
static electricity by touching a grounded piece of metal. 
Otherwise, you may damage static-sensitive components.
w
Warning:
Be careful when working inside the printer as some components 
are sharp and may cause injury.
 
						

							Installing Options299
8
8
8
8
8
8
8
8
8
8
8
8
1. Turn the printer off and unplug the power cord.
2 . R e m o v e  t h e  f o u r  s c r e w s  f r o m  t h e  c o v e r  o n  t h e  b a c k  s i d e  o f  t h e  
printer.
 
						

							300Installing Options 3. Hold the cover with both hands and pull it toward you to 
remove it.
w
Warning:
Be careful when touching the circuit board inside the back 
side cover since some parts may be very hot.
4. Identify the connection socket for the Hard Disk Drive.