Epson AcuLaser 2600DN User Manual

							Replacing Consumable Products331
9
9
9
9
9
9
9
9
9
9
9
9
Waste Toner Collector
Handling precautions
Always observe the following handling precautions when 
replacing the consumable products.
Do not reuse toner found in the waste toner collector. 
w
 Warning:
❏Do not dispose of the used consumable products in fire, as it 
may explode and cause injury. Dispose of it according to local 
regulations.
❏Keep the consumable products out of the reach of children. 
Replacing the waste toner collector
Follow the steps below to replace the waste toner collector and 
the filter. 
1. Open cover D.
 
						

							332Replacing Consumable Products 2. Remove the waste toner collector.
3. Take the cap off and lid the waste toner collector with it.
Note:
When placing the waste toner collector that is removed, lay it on a 
flat surface with the capped side facing up to prevent the toner 
content from spilling out.
 
						

							Replacing Consumable Products333
9
9
9
9
9
9
9
9
9
9
9
9
4. Install the new waste toner collector into the printer.
5. Remove the filter from the printer.
6. Take the new filter out of its package. Insert the new filter to 
the printer.
 
						

							334Replacing Consumable Products 7. Close cover D.
 
						

							Cleaning and Transporting the Printer335
10
10
10
10
10
10
10
10
10
10
10
10
Chapter 10 
Cleaning and Transporting the Printer
Cleaning the Printer
The printer needs only minimal cleaning. If the printer’s outer 
case is dirty or dusty, turn off the printer and clean it with a soft, 
clean cloth moistened with a mild detergent.
c
Caution:
Never use alcohol or paint thinner to clean the printer cover. 
These chemicals can damage the components and the case. Be 
careful not to get water onto the printer mechanism or any 
electrical components.
 
						

							336Cleaning and Transporting the Printer
Cleaning the output tray
1. Open the extension on the output tray.
2. Gently wipe the exposed paper path area with a well-wrung 
cloth.
 
						

							Cleaning and Transporting the Printer337
10
10
10
10
10
10
10
10
10
10
10
10
3. Close the extension on the output cover.
Cleaning the pickup roller
1. Make sure that the printer is turned off, then open the MP tray.
 
						

							338Cleaning and Transporting the Printer 2. Gently wipe the rubber parts of the pickup roller inside the 
MP tray with a wet, well-wrung cloth.
3. Close the MP tray.
Cleaning the photoconductor wire (knob [a])
1. Open cover D and remove the waste toner collector.
 
						

							Cleaning and Transporting the Printer339
10
10
10
10
10
10
10
10
10
10
10
10
Note:
When placing the waste toner collector that is removed, stand it on 
a flat surface leaning against something stable.
2. Hold the cleaning knob [a] and move it slowly in and out a 
few times.
Note:
Move the knob completely in and out. Otherwise, the printer may 
not be cleaned effectively.
3. Close cover D.
Cleaning the exposure window (knob [b])
1. Open cover D and remove the waste toner collector.
Note:
When placing the waste toner collector that is removed, stand it on 
a flat surface leaning against something stable.
 
						

							340Cleaning and Transporting the Printer 2. Hold the knob [b] and move it slowly in and out a few times.
Note:
Move the cleaning knob completely in and out. Otherwise, the 
printer may not be cleaned effectively.
3. Close cover D.
Transporting the Printer
For long distances
If you need to transport your printer for long distances, carefully 
repack it using the original box and packing materials.
Follow the steps below to repack your printer.
1. Turn off the printer and remove the following items:
❏Power cord
❏Interface cable