Epson Aculaser M 2000 Service Manual

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 171
Confidential
2nd Transfer Unit

	

The 2nd transfer roller is included in the Transfer unit, and the 2nd transfer roller 
should be replaced with other parts in the Transfer unit at the same time.
1. Open the Right Door.
2. Unlock the Lock levers [1] (at two palaces), remove the 2nd Transfer Roller [2].A1
[1] [2]
Ozone Filter

	

The ozone filter is included in the Transfer unit, and the filter should be replaced with 
other parts in the Transfer unit at the same time.
1. Holding onto the hook, remove the Ozon Filter [1].
B1
[1] 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 172
Confidential
Dust Filter

	

The dust filter is included in the Transfer unit, and the filter should be replaced with 
other parts in the Transfer unit at the same time.
IF the Duplex unit is mounted, remove it.
1. Remove the Dust Filter [1].
C1
[1]
Feed Roller (Standard Cassette)

	

The separation roller should be replaced, whenever the feed roller is replaced. 
 
1. Slide out the standard paper cassette.
2. Lock the paper lifting plate [1] into position.
3. Snap off the C-clip [2] from the feed roller assy [3].
4. Remove the shaft for the feed roller assy [3] from the front bushing.D1
[1]
[2]
[3] 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 173
Confidential5. Snap off the C-clip [4], one collar [5] and remove the Feed Roller [6].

	


When installing the Feed Roller with a new one, make sure to reset the life counter. 
(Refer to Chapter 5 “ADJUSTMENT”) (p313))
[4]
[5][6]
Separation Roller (Standard Cassette)

	

The pickup roller should be replaced, whenever the separation roller is replaced.
1. Slide out the standard paper cassette.
2. Remove two Screws [1] and the Separation Roller ounting bracket assy [2].
E1
4038F2C002DB
[1] [2] 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 174
Confidential3. Take off the rubber stopper [3], shaft [4], spring [5], and guide plate [6] to remove the 
Separation Roller fixing bracket assy [7].
4. Snap off the E-ring [8] and the Separation Roller [9].
4038F2C003DB
4037F2C509DA
[6]
[3] [4]
[7]
[5]
[9]
[8] 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 175
Confidential4.3.3  Group 3CONTENT
Parts/Units to be Disassembled
Guide
Toner Cartridge (+ Odor Filter)Front CoverPH Interface Board (PWB-D)PH Unit
ABCDOdor Filter
A
A
Toner Cartridge
Front Cover
BPH Interface Board 
(PWB-D)
C
PH Unit
D 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 176
ConfidentialDISASSEMBLY FLOWCHART
D2
B2
C2
D3
B3
C3
D4
B4
C4
D5
B5
C5
D6
B6
C6
D7
B7
C7
D8
B8
C8
B1
A1 C1D1
C9D9
C10
D10
Start
Toner Cartridge (+ Odor Filter)
(P. 177)
Waste Toner Collector
 + Exhaust Filter 
(P. 178)
Photoconductor Unit
(P. 178)
Rear Left Cover + Front Left Cover
(P. 179)
Right Rear Cover + Rear Cover
(P. 180)Exit Tray(P. 180)Front Door(P. 181)Front Cover(P. 182)
Transfer Belt Unit
(P. 184)
PH Interface Board (PWB-D)
(P. 185)
PH Unit(P. 188) 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 177
Confidential
Toner Cartridge (+ Odor Filter)
†
Dont burn the Toner Cartridge. Toner may spatter and cause fire. And It may 
result in burns.
†
Dont touch the inside printer which is not specified while replacing. It may result 
in burns or cause degrading of print quality.
1. Open the Front Door.
2. Push up the place indicated by arrow as shown in the figure above and slowly pull the Toner 
Cartridge toward.
Place the pulled Toner Cartridge face down.A1
B1
C1
D1

	

Replace the Odor Filter when replacing black (K) Toner Cartridge.
3. Remove the Odor Filter from the left side of the printer. 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 178
Confidential
Photoconductor Unit
Dont burn the Photoconductor Unit. Toner remnants may spatter and cause fire. And 
It may result in burns.
1. Open the Front Door.
2. Push down the protrusion of the Photoconductor Unit to be replaced, and slowly pull it 
toward.
B2
C2
D2
Waste Toner Collector + Exhaust Filter
Dont burn the used Waste Toner Collector. Toner may spatter and cause fire. And It 
may result in burns.

	

The Exhaust Filter is supplied with the Waste Toner Collector. Replace it when 
replacing the Waste Toner Collector.
1. Open the Front Door.
2. Push the unlocking knob in the printer side. And then, pull out the Waste Toner Collector 
which popped up from the printer.
B3
C3
D3 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 179
Confidential3. Remove the Exhaust Filter from the top face of the printer.
Rear Left Cover + Front Left Cover
1. Remove two Screws [2], and remove the Rear Left Cover [3].
2. Open the Front Door [1].
3. Remove two Screws [4], and remove the Front Left Cover [5].
B4
C4
D4
[1] [2]
[3][4]
[5] 
						

							EPSON AcuLaser C9200NRevision D
DISASSEMBLY AND ASSEMBLY      Main Unit Disassembly/Reassembly 180
Confidential
Rear Right Cover + Rear Cover
1. Open the Right Door [1].
2. Remove three Screws [2], and remove the Right Rear Cover [3].
3. Remove nine Screws [4], and remove the Rear Cover [5].
B5
C5
D5
[1]
[3] [2] [4][4] [4]
[5]
Exit Tray
1. Open the Upper Fusing Cover [2].
2. Remove two Claws [3], and remove the Upper Fusing Cover [2].
B6
C6
D6
[2]
[3][3]
4039F2C019DA