Epson EPL N3000DTS User Manual

							228Replacing the Consumable ProductNote:
When the optional Stacker is installed, lower the Stacker after 
closing cover A.
Fuser Unit
Prepare a new fuser unit for replacement when you get a message 
informing you to do so.
Handling precautions
Note the following handling precautions before replacing the 
fuser unit:
❏Do not touch the surface of the fuser unit. Doing so may 
impair print quality.
w
Warning:
❏The fuser unit can be very hot if the printer has been in use. 
Turn the printer off and wait for 40 minutes until the 
temperature has subsided before replacing the fuser unit.
❏Keep the fuser unit out of the reach of children.
Replacing the fuser unit
Follow these steps to replace the fuser unit.
 
						

							Replacing the Consumable Product229
8
8
8
8
8
8
8
8
8
8
8
8
1. Turn off the printer and unplug the power cord and the 
interface cable. 
Note:
If the printer has been in use, wait at least 40 minutes until the fuser 
cools down before replacing it.
2. Lift the paper path lever.
 
						

							230Replacing the Consumable Product 3. Open cover B.
4. Pull down the two levers at either side of the fuser unit.
 
						

							Replacing the Consumable Product231
8
8
8
8
8
8
8
8
8
8
8
8
5. Remove the fuser unit slowly.
Note:
When removing the fuser unit, hold your hands as shown above, on 
the three tabs on both sides of the bottom of the fuser unit.
6. Slowly insert the new fuser unit.
 
						

							232Replacing the Consumable Product 7. Lift up the two levers at either side of the fuser unit and push 
down the levers at both ends of the fuser unit to lock it.
8. Close cover B.
9. Reconnect the interface cable and power cord, and then turn 
on the printer.
 
						

							Replacing the Consumable Product233
8
8
8
8
8
8
8
8
8
8
8
8
10. Press the  Up or  Down button several times until 
Reset Menu appears on the control panel, and then press the 
Enter button.
11. Press the  Down button to display Reset Fuser Counter, 
and then press the  Enter button.
Cleaning the Printer
The printer needs only minimal cleaning. If the printer’s outer 
case is dirty or dusty, turn off the printer and clean it with a soft, 
clean cloth moistened with a mild detergent.
 
						

							234Replacing the Consumable Product
c
Caution:
Never use alcohol or paint thinner to clean the printer cover; these 
chemicals can damage the components and the case. Be careful 
not to get water onto the printer mechanism or any electrical 
components.
Cleaning the pickup roller
If the paper jam occurs frequently, wipe the pickup roller with a 
clean dampened cloth. Follow the steps below.
1. Turn the printer off and open cover A slowly.
 
						

							Replacing the Consumable Product235
8
8
8
8
8
8
8
8
8
8
8
8
2. Hold the handle of the imaging cartridge and pull out.
Note:
Place the cartridge on a clean, flat surface.
3. Remove the two pick up rollers by bending their tabs slightly 
outwards while sliding them off the spindles.
 
						

							236Replacing the Consumable Product 4. With a clean damp cloth, wipe the pickup roller’s rubber 
parts.
5. Reattach the pickup rollers as shown below. Then, fit the hook 
in the concave part of the shafts to fix them.
Note:
Fit the convex parts of the pickup rollers in the concave parts of the 
shaft.
rubber parts
 
						

							Replacing the Consumable Product237
8
8
8
8
8
8
8
8
8
8
8
8
6. Reinstall the imaging cartridge.
7. Close cover A until it clicks shut.
Transporting the Printer
For long distances
If you need to transport your printer for long distances, carefully 
repack it using the original box and packing materials.
Follow these steps to repack your printer.
1. Turn off the printer.
2. Unplug the power cord from the electrical outlet.
3. Remove all installed options. For information on removing 
options, see the section under Installing Options.