HP Business InkJet 3000 User Manual

							ENWWUnderstanding control-panel messages     49    
[COLOR] INK CARTRIDGE IS EXPIRING SOONWhen the ink cartridge expires, replace with a new HP 
ink cartridge.
Press 
 (Resume button) to clear this message.
NON-HP [COLOR] INK CARTRIDGE... A non-HP ink cartridge has been detected.
Replace with a HP ink cartridge.
To continue printing with non-HP ink cartridge, press 
and hold 
 (Power button), press  (Resume 
button) three times, and release 
 (Power button). 
However, print quality and ink level information may 
be affected.
HP recognizes customer’s choice, but cannot 
guarantee the quality or reliability of non-HP ink 
cartridges. Printer services or repairs required as a 
result of using non-HP ink cartridges will not be 
covered under warranty.
If you believe you have purchased a genuine HP ink 
cartridge, visit http://www.hp.com/go/anticounterfeit.
INSUFFICIENT MEMORYMore data has been received from the computer than 
fits in the printer’s memory. You may try to compress 
your file before printing or use a lower print quality. 
Alternatively, you can add extra DIMMs to increase the 
printer’s memory.
Press 
 (Resume button) to clear this message.
POWERING OFFThe printer is preparing to turn off. Please wait.
PROCESSING JOB...The printer is performing some tasks. Please wait.
READYThe printer is ready to accept print jobs.
MessageDescription
 
						

							50    5 - Control panelENWW
Understanding control-panel menus
Information menu 
This menu contains printer information pages that give details about the printer and 
its configuration. To print an information page, scroll to the desired page and 
press (Select button).
MessageDescription
PRINT MENU MAPThis item prints a map of the printer menu structure.
PRINT CONFIGURATION PAGEThis item prints a page describing the current printer 
configuration (such as firmware version, model, accessories 
installed, I/O support, or other details). If an HP Jetdirect print 
server is installed, a second page will be printed, which 
displays the settings for the HP Jetdirect print server.
PRINT DIAGNOSTIC PAGEThis item prints a diagnostic page describing the current 
printer configuration, printhead information, and technical 
information.
PRINT DEMOThis item prints a demonstration page.
PRINT PCL FONT LISTThis item prints the available PCL fonts.
PRINT PS FONT LISTThis item prints the available PS (emulated PostScript) fonts.
SHOW IP ADDRESSThis item displays the printer’s default IP address.
 
						

							ENWWUnderstanding control-panel menus     51    
Paper Handling menu 
These settings control the default media options. However, settings made in the software 
application from which you print or in the printer driver override control panel settings for the 
current print job.
MessageValue or SubmenuDescription
TRAY 1 SIZE NOT SET
SUPER B (13 X 19 IN.)
A3 NOBI
A3
A4
A5
A6
B4 (JIS)
B5 (JIS)
EXECUTIVE
LEGAL
LETTER
STATEMENT
11 X 17
ENVELOPE #10
ENVELOPE A2
ENVELOPE C5
ENVELOPE C6
ENVELOPE DL
JAPANESE ENVELOPE KAKU #2
ENVELOPE MONARCH
JAPANESE ENVELOPE CHOU #3
JAPANESE ENVELOPE CHOU #4
HP GREETING CARD ENVELOPE
4 X 6 IN. WITH TAB
4 X 6 IN.
5 X 8 IN.
OFUKU HAGAKI
HAGAKI CARD
CUSTOMThis item allows you to select the 
media size loaded in Tray 1.
Default = NOT SET
TRAY 1 TYPE NOT SET
PLAIN PAPER
HP PREMIUM PAPER
HP HEAVYWEIGHT PREMIUM PAPER
HP PREMIUM TRANSPARENCY FILM
HP PREMIUM PLUS TRANSPARENCY FILM
HP EVERYDAY PHOTO PAPER, MATTE FINISH
HP EVERYDAY PHOTO PAPER, SEMI GLOSS
HP COLORFAST PHOTO PAPER, GLOSSY
HP PREMIUM + PHOTO PAPER, GLOSSY
HP PREMIUM + PHOTO PAPER, MATTE
HP PREMIUM PHOTO PAPER, GLOSSY
HP PHOTO PAPER, GLOSSY
HP BROCHURE & FLYER, GLOSS
HP BROCHURE & FLYER, MATTEThis item allows you to select the 
media type loaded in Tray 1.
Default = NOT SET
 
						

							52    5 - Control panelENWW
TRAY 2 SIZE NOT SET
SUPER B (13 X 19 IN.)
A3 NOBI
A3
A4
B4 (JIS)
B5 (JIS)
EXECUTIVE
LEGAL
LETTER
STATEMENT
11 X 17
CUSTOMThis item allows you to select the 
media size loaded in Tray 2. 
Default = NOT SET
TRAY 2 TYPE NOT SET
PLAIN PAPERThis item shows the media type 
for Tray 2.
Default = NOT SET
DEFAULT TRAY TRAY 1
TRAY 2This item allows you to set the 
default tray. If a tray is not 
selected in the printer driver, the 
printer will draw media from this 
tray.
Default = TRAY 2
AUTOMATIC MEDIA 
TYPE SENSEOFF
ONThis item allows you to enable the 
media type sensor. 
Default = OFF
FAST NORMAL PRINT 
SPEEDHIGH
LOWThis item helps to improve the 
printing speed when Fast Normal 
print quality is selected.
Default = HIGH
OUTPUT RAMP 
EXTENSIONON 
OFFThis item enables the printers 
output ramp to be extended to 
hold the paper before releasing it 
onto the output tray.
Default = OFF
MessageValue or SubmenuDescription
 
						

							ENWWUnderstanding control-panel menus     53    
Configure Device menu 
Items in this menu affect printer behavior. Configure the printer according to your 
printing needs. 
Resetting the printer
You may need to reset the printer in the following circumstances: 
zYou want to restore the printer’s default settings.
zCommunication between the printer and computer has been interrupted.
CAUTIONWhen you use the restore factory settings option on this menu, you can lose printer 
configuration settings.
NoteThis option does not reset an HP Jetdirect print server to its default settings if one is installed 
in the printer. To reset the HP Jetdirect print server, see Resetting the HP Jetdirect print server.
MessageValue or SubmenuDescription
PRINT PS/PCL6 ERRORS OFF
ON This item allows you to print a list of 
PS/PCL6 errors.
Default = OFF
UNATTENDED PRINTING OFF
ON This item sets the printer to pause 
during large print jobs (after every 
100 pages) so that you can clear the 
output tray. 
Default = OFF
SYSTEM SETUP PERSONALITYThis item sets the default personality 
to automatic switching, PCL5, PCL6, 
or PostScript emulation.
Default = AUTO
LANGUAGEThis item sets the default language. 
Select it from the list of supported 
languages.
Default = ENGLISH
I/O I/O TIMEOUTThis item sets the length of time 
(from 5 to 300 seconds) that the 
printer waits for remaining data for a 
print job. If that time is exceeded, 
the printer prints the print job. 
Default = 15
EIOThis item allows you to access 
submenus for the HP Jetdirect print 
server, if one is installed. For details, 
see Changing networking parameters 
from the control panel.
RESTORE FACTORY 
SETTINGSYES
NOThis item restores all values to the 
printer’s predetermined factory values.
 
						

							54    5 - Control panelENWW
Printing menu
The items in this menu are used when printing from MS-DOS®, UNIX, and Linux. If your 
computer is running Windows or Mac OS, configure these settings using the printer driver. 
MessageValue or SubmenuDescription
COPIES 1 - 100This item sets the number of 
copies to print.
Default = 1
DEFAULT PAPER 
SIZELETTER
A4This item allows you to set the 
default media size.
Default = LETTER 
DEFAULT PAPER 
TYPEPLAIN PAPER
HP PREMIUM PAPER
HP HEAVYWEIGHT PREMIUM PAPER
HP PREMIUM TRANSPARENCY FILM
HP PREMIUM PLUS TRANSPARENCY FILM
HP EVERYDAY PHOTO PAPER, MATTE FINISH
HP EVERYDAY PHOTO PAPER, SEMI GLOSS
HP COLORFAST PHOTO PAPER, GLOSSY
HP PREMIUM + PHOTO PAPER, GLOSSY
HP PREMIUM + PHOTO PAPER, MATTE
HP PREMIUM PHOTO PAPER, GLOSSY
HP PHOTO PAPER, GLOSSY
HP BROCHURE & FLYER, GLOSS
HP BROCHURE & FLYER, MATTEThis item allows you to set the 
default media type.
Default = PLAIN PAPER
DEFAULT QUALITY 
LEVELFAST
FAST NORMAL
NORMAL
BESTThis item allows you to select the 
default level for print quality. This 
setting is used if the print job 
contains no print-quality selection.
Default = NORMAL
DUPLEX OFF
ON This item appears only when an 
auto-duplex unit is installed. Set 
the value to ON to print on both 
sides (duplex) or OFF to print on 
one side of a sheet of paper. 
For more information, see Printing 
on both sides (duplexing).
Default = OFF
OVERRIDE
A4/LETTERNO
YESThis item sets the printer to print 
an A4 job on letter-size paper 
when no A4 paper is loaded, or to 
print a letter-size job on A4 paper 
when no letter-size paper is 
loaded.
Default = NO 
PCL FORM LENGTH
ORIENTATION
FONT NUMBER
FONT PITCH
FONT POINT SIZE
SYMBOL SET
ISE FONTS
APPEND CR TO LFThis item allows you to configure 
settings for printer control 
language (PCL) when using the 
PCL 5c or PCL 6 printer 
personality.
 
						

							ENWWUnderstanding control-panel menus     55    
Maintenance menu
Print Quality menu
This menu allows you to adjust aspects of print quality, including calibration, printhead 
alignment, and quality level.
.
Diagnostics menu
This menu allows you to view the printer’s event log.
Paper Path Test menu
This menu allows you to test various components of the printer so you can identify and solve 
problems.
MessageValue or 
SubmenuDescription
ALIGN PRINTHEADSN.A. This item begins the printhead alignment 
process.
COLOR CALIBRATIONN.A. This item begins the color calibration process.
LINEFEED CALIBRATIONN.A. This item begins the linefeed calibration 
process.
CLEAN PRINTHEADSN.A. This item begins the printhead cleaning 
process.
MessageDescription
SHOW EVENT LOGThis item displays the last 10 events on the control panel, 
starting with the most recent event.
MessageDescription
START TEST
SOURCE
DUPLEX
COPIESThe items on this menu let you test the paper handling features 
of the printer. If you have difficulty printing from one of the trays, 
or printing on both sides of the page, run this test to verify that the 
paper path is working properly.
 
						

							56    5 - Control panelENWW
Changing networking parameters from the control panel
The EIO (enhanced input/output) submenu appears on the I/O menu only when an 
HP Jetdirect print server is installed. If the printer contains an HP Jetdirect print server, 
you can configure basic networking parameters using the EIO menu. Network printer 
administrators can also use HP Web Jetadmin or the embedded Web server to configure 
these and other parameters remotely. 
NoteThe items available on the menu vary depending on the particular print server that is installed.
EIO menu
This menu allows you to configure the networking parameters for the printer. To check the 
printer’s current network settings, print a configuration page. See Understanding and printing 
the configuration page.
MessageValue or SubmenuDescription
CFG NETWORK NO
YESSelects whether or not you want to use the EIO 
Jetdirect menu items. You must change this option 
to YES each time you want to use the EIO Jetdirect 
menu.
TCP/IP
IPX/SPX
ATALK
DLC/LLCON
OFFSelects whether to enable or disable a protocol. 
Select OFF to disable a protocol.
CFG TCP/IP NO
YESSelects whether to use the TCP/IP menu and set the 
TCP/IP protocol parameters.
In the TCP/IP menu, you can specify BOOTP=YES or 
DHCP=YES for TCP/IP parameters to be automatically 
configured by a BootP or DHCP server when the 
printer is turned on. 
If you specify BOOTP=NO and DHCP=NO, you can 
choose AUTO IP=YES to have a link-local address 
169.254.x.x assigned automatically.
If you specify BOOTP=NO, DHCP=NO, and AUTO IP=NO, 
you can manually set the following TCP/IP 
parameters from the control panel: 
zIP address (IP) 
zSubnet Mask (SM) 
zSyslog Server (LG) 
zDefault Gateway (GW) 
zIdle Timeout period (default is 270 seconds; 
0 disables the timeout) 
When setting IP numbers, press   (Up Arrow 
button) to increase the number by 1. Press 
 
(Down Arrow button) to decrease the number by 1. 
Press   (Select button)
 to make your selection.
 
						

							ENWWChanging networking parameters from the control panel     57    
CFG IPX/SPX NO
YESSelects whether to use the IPX/SPX menu and set 
the IPX/SPX protocol parameters.
In the IPX/SPX menu, you can specify the frame 
type parameter used on your network. 
zThe default is AUTO, which automatically sets 
and limits the frame type to the first one 
detected.
zFor Ethernet networks, frame type selections 
include EN_8023, EN_II, EN_8022, and EN_SNAP.
zFor Token Ring networks, frame type selections 
include TR_8022 and TR_SNAP. 
In the submenu for Token Ring cards, you can also 
specify the NetWare Source Routing parameter, 
which can be AUTO (default), OFF, SINGLE R, 
orALL RT.
WEB HTTPS
HTTP/HTTPSFor configuration management, specify whether the 
embedded Web server will accept communications 
using HTTPS (Secure HTTP) only, or both HTTP 
and HTTPS.
zHTTPS: For secure, encrypted communications, 
only HTTPS access is accepted. The print 
server will appear as a secure site.
zHTTP/HTTPS: Access using either HTTP or 
HTTPS is permitted.
SECURITY KEEP
RESETSpecify whether the current security settings on the 
print server will be saved or reset to factory defaults.
zKEEP (default): The current security settings are 
maintained.
zRESET: Security settings are reset to factory 
defaults.
CFG LINK NO
YESSelects whether you want to manually configure the 
HP Jetdirect 10/100Base-TX print server’s network 
link speed and communication mode.
The HP Jetdirect settings must match the network. 
The default setting is NO, which bypasses the link 
configuration menu items.
If you specify YES, you can select one of the 
following link configuration menu items:
zAUTO (default): The print server automatically 
configures itself to match the link speed and 
communication mode of the network. If it fails, 
100TX HALF will be set.
z10T HALF: 10 Mbps, half-duplex operation 
z10T FULL: 10 Mbps, full-duplex operation 
z100TX HALF: 100 Mbps, half-duplex operation
z100TX FULL: 100 Mbps, full-duplex operation
MessageValue or SubmenuDescription
 
						

							58    5 - Control panelENWW
Novell NetWare frame type parameters
The HP Jetdirect print server automatically selects a NetWare frame type. Select a frame type 
manually only when the print server selects an incorrect frame type. To identify the frame type 
chosen by the HP Jetdirect print server, print a configuration page from the control panel. 
SeeUnderstanding and printing the configuration page.
The following frame types are supported:
zEthernet_802.3
zEthernet_II
zEthernet_802.2
zEthernet_SNAP
Disabling network protocols (optional)
By factory default, all supported network protocols are enabled. Disabling unused protocols 
has the following benefits: 
zIt decreases printer-generated network traffic.
zIt prevents unauthorized users from printing to the printer.
zIt provides only per tinent information on the Configuration page.
zIt allows the control panel to display protocol-specific error and warning messages.
To disable network protocols
NoteDo not disable the IPX/SPX protocol if Windows 98, Windows NT, Windows Me, 
Windows 2000, or Windows XP users will be printing to the printer.
1Press   (Select button) on the control panel to enter the menus.
2Press   (Down Arrow button) to highlight CONFIGURE DEVICE, and then 
press (select button).
3Press   (Down Arrow button) to highlight I/O, and then press   (Select button).
4Press   (Down Arrow button) to highlight EIO SUBMENU, and then 
press  (Select button).
5Press   (Down arrow button) to highlight the network protocol you want to disable, 
and then press   (Select button).
6Press   (Down Arrow button) to highlight OFF, and then press   (Select button).
7Press   (Cancel button) to return to the READY state.