Lucent Technologies Definity Application Notes For Type Approval Manual

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
263 Israel 
4 Wire Digital Line
2 Wire Digital Line
Data Line
BRI-U Line
BRI-ST Line
Table 36. Recommended and Available CPs in Israel
Equipment Equipment Type
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
264 Italy (Lucent Technologies) 
Italy (Lucent Technologies)
Ta b l e  3 7 shows the rec ommended  c irc uit p ac ks.
Table 37. Recommended and Available CPs in Italy (Lucent Technologies)
Equipment Equipment Type
Cab inet Typ e & Power GAC-MCC DC-MCC AC-SCC AC-CSCC 
AC-CMC
AC Power Voltag e & Freq 220V/50Hz
Ring Generator 25Hz
Tone Detec tor > TN2182B > TN744D TN420C
Tone Cloc k > TN2182B TN780 
R2MFC Circ uit n/a
Sp eec h Synthesizer > TN433 
Call Classifier > TN744D
Announc ement TN750C TN750B
Analog  DID Trunk > TN2179
Analog  CO Trunk (No PPM)  n/a
Analog  CO Trunk (w/PPM) #TN465C > TN2138
4 Wire Tie Trunk > TN2140B TN2140
2 Wire Tie Trunk n/a
Auxiliary Trunk > TN763D 
Dig ital CO/DID Trunk > TN464Fv5 
Dig ital Tie Trunk > TN464Fv5
Dig ital PRI CO Trunk
Dig ital BRI Trunk > TN2185
Dig ital Converter PRI-DASS   
Dig ital Converter PRI-DPNSS TN-CCSC-2
Dig ital Converter PRI-BRI   
8 Port Analog  Line n/a
16 Port Analog  Line #TN2183 > TN2135
24 Port Analog  Line n/a
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
265 Italy (Lucent Technologies) 
Country-Specific Feature
You c an use DEFINITY ECS the Europ ean CEPT Ad vic e of Charg e feature in Italy. 
Refer to the DEFINITY ECS Ad ministration and  Feature Desc ription for more 
information ab out Ad vic e of Charg e.
Feature Administration
The sc reen d isp lays shown in this sec tion were effec tive the d ate the typ e 
ap p roval was award ed . The sc reens may have c hang ed  sinc e that d ate.
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nARS/AAR Ad ministration
To enab le ARS administration, on the System-Parameters 
Customer-Op tions sc reen, set the ARS
 field  to y
. You also should check all 
ARS/AAR d efaults. These d efaults were intended  for U.S. op eration and  
c ertain values are likely to b e inap p ropriate internally. In p artic ular, the 
following c all types (appear as ARS/AAR defaults) typically are not used in 
non-North Americ an ARS/AAR tab les: 4 Wire Digital Line > TN754B 
2 Wire Digital Line #TN2224 > TN2181 
Data Line > TN726B 
BRI-U Line
BRI-ST Line
fnp a: North Americ an numb ers with an area c od e.
hnp a: North Americ an numb ers without an area c od e.
svc North Americ an numb ers of the screen ‘‘x11’’.
Table 37. Recommended and Available CPs in Italy (Lucent Technologies)
Equipment Equipment Type
Continued on next page 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
266 Italy (Lucent Technologies) 
Luc ent rec ommend s only the following  c all typ es b e used  outside North 
Americ a:
System Parameter Administration
Only those feature-related  p arameters that may have a Typ e Ap p roval or b asic  
c onnec tivity imp lic ation for a p artic ular c ountry are listed  here.
nFeature-Related System Parameters Ad ministration
— System-Parameters Customer-Op tions
nOff Premise Tone Detec tion Timeout: 10 sec
nTrunk-to-Trunk Transfer: Restric ted
nCoverag e - Sub sequent Redirec tion No Answer Interval: 3
nMusic /Tone on Hold : tone
nDID/TIE/ISDN Interc ep t Treatment: Attend ant
nTime b efore Off-hook Alert: 10
nServic e Ob serving  Warning  Tone: Yes
nPub lic  Network Trunks on Conferenc e Call: 1
nConference Parties With PNTs: 3
nConferenc e Parties Without PNTs: 6
nLine Interc ep t Tone Timer: 30
nNig ht Servic e Disc onnec t Timer: 180 sec
nShort Interd ig it Timer: 3 sec
nUnanswered DID Call Timer: 25 sec
nAuto-Hold : Yes1
nAttend ant Tone: Yes
nBridg ing  Tone: No
nConferenc e Tone: No
nIntrusion Tone: Yes
nRep etitive Call Waiting Tone: Yes
nDID Busy Treatment: Attend ant
nPull Transfer: Yes int: For all international numb ers.
natl: For all national PN numb ers.
p ub u: For all other external (that is, not extensions) numb ers. 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
267 Italy (Lucent Technologies) 
nUp d ate Transferred  Ring  Pattern: Yes
nLevel of Tone Detec tion: Prec ise
nWait Answer Sup ervision Timer: Yes
nMisop eration Alerting : Yes
nAllow c onferenc e via Flash: Yes
nOutp ulse Without Tone: No
nNetwork Feed b ac k During  Tone Detec tion: No
nInterc ept Treatment On Failed  Trunk Transfers: Yes
nStation Tone Forward  Disc onnec t: Interc ep t
n(Station-to-switc h) Rec all Timing :
nFlashhook Interval: Yes
nUp p er Bound : 1000 ms
nLower Bound : 200 ms
— System Parameter Country Op tions Ad ministration
nComp and ing  Mode: A-law
nBase Tone Generation Set: 4
nTone Detec tion Mod e: 1
nDig ital Loss Plan: 4
nInterd ig it Pause: short
nAnalog  Ring ing  Cad enc e: 4
nAnalog  Line Transmission: 4
nCustomized  Ind ivid ual Tones
Analog Trunk Administration
nCO Trunks
— Trunk Group  Sc reen
nGroup  Typ e: CO
nDirec tion: two-way
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nCountry: 4
nTrunk Gain: hig h
nDig it Ab sorp tion List: b lank
nPre f i x -1 :  N o 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
268 Italy (Lucent Technologies) 
nTrunk Type: loop -start or g round -start
nOutg oing  Dial Typ e: tone
nTrunk Termination: rc  (c omp lex imp ed anc e)
nDisc onnec t Timing : 500 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
nParameters b ased  on loop  leng th (whic h itself is not 
ad ministrable)
nAuto Guard : no
nCall Still Held : no
nRec eive Answer Sup ervision: no
nAnswer Supervision Timeout: 10 (This sets both the CP 
firmware timer and  software timer. Set to 0 for any trunk that 
will rec eive answer sup ervision.)
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.
— Trunk Group  Ad ministration sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  CO 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 50 ms
nOutg oing  Disc onnec t: 50 ms
nOutg oing  Dial Guard : 1000 ms
nInc oming  Glare Guard : 200 ms
nOutg oing  Glare Guard : 200 ms
nRing  Monitor Timer: 5200 ms
nInc oming  Seizure: 500 ms
nOutg oing  End -of-Dial: 10 sec
nOutg oing  Seizure Resp onse: 20 sec
nProg rammed  Dial Pause: 1500 msLoop Length Trunk Gain Terminal Balance
short low y
long hig h y 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
269 Italy (Lucent Technologies) 
nDisc onnec t Sig nal Error: 255 sec  (only Ground  Start)
nFlash Leng th: 100 ms
nOutp ulsing  Information:
— PPS:  1 0  p p s
— Make: 50 ms
— Break: 50 ms
— PPM :  Ye s
— Freq uenc y: 12kHz
nEn d  t o  En d  Sig n a li n g
— Tone: 350 ms (ac c ep t default)
nDID Trunks
— Trunk Group  sc reen
nGroup  Typ e: DID
nCountry: 4
nTrunk Type: immed -start
nInc oming  Dial Typ e: tone
nTrunk Termination: rc  (c omp lex imp ed anc e)
nDisc onnec t Timing : 500 ms (This field  will not be used  with 
CPs that c an ac c ep t the Inc oming  Disc onnec t and  Outg oing  
Disc onnec t timers. Set these latter two timers from the 
Ad ministrab le Timers Sc reen.)
nDig it Treatment: b lank
nDig its: b lank
nExp ec ted  Dig its: d ep end s on system size and  numb ering  
plan
nTerminal Balanc ed : yes
nExtend ed  Loop  Range: (Used  Only with TN459) no
nDrop  Treatment: silenc e
nTrunk Gain: hig h
nDisc onnec t Sup ervision: no
nInc oming  Rotary Timeout (sec ): 5 sec  (This field  will not b e 
used  with CPs that c an ac c ept the Inc oming  Partial Dial 
timer. Set this timer from the Ad ministrab le Timers sc reen.) 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
270 Italy (Lucent Technologies) 
— Trunk Group  Ad ministration sc reen (Timing )
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  DID 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 500 ms
nInc oming  Dial Guard : 50 ms
nFlash Leng th: 100 ms
nInc oming  Inc omplete Dial Alarm: 255 sec
nTi e  Tru n k s
The TN2140B is used  for E&M trunks that may b e ad ministered  as either 
Continuous or Disc ontinuous. This sec tion lists the only valid  
ad ministration c omb inations p ossib le for these trunks.
Use the following  ad ministration for these typ es:
— Continuous T1
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nTrunk Sig naling  Typ e: c ont
nTrunk Type (in/out): c ont/c ont
nSend  Release Ac k: y
nRec eive Release Ac k: y
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Continuous T2
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Sig naling  Typ e: c ont
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: y
nRec eive Release Ac k: y
nDisc onnec t Sup ervision - In: no 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
271 Italy (Lucent Technologies) 
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: y
nRec eive Answer Sup ervision: y
— Disc ontinuous T1
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: y
nRec eive Release Ac k: y
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Disc ontinuous T2
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nTrunk Type (in/out): d isc /d isc
nSend  Release Ac k: n
nRec eive Release Ac k: n
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: y
nRec eive Answer Sup ervision: y
— Disc ontinuous T3
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing) 
						

							DEFINITY® Enterprise Communications Server Application Notes 
for Type Approval    Issue 1
June 1999
Application Notes for Type Approval 
272 Italy (Lucent Technologies) 
nTrunk Type (in/out): d isc /d isc
nSend  Release Ac k: n
nRec eive Release Ac k: n
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Disc ontinuous T5
nGroup  Typ e: tie, tand em, ac c ess, ap lt, or rlt
nTrunk Signaling Type: dis
nDial Ac c ess: Customer Op tion (No is rec ommend ed  to avoid  
toll fraud ) (Yes, for app roval testing)
nTrunk Type (in/out): immed /immed
nSend  Release Ac k: n
nRec eive Release Ac k: n
nDisc onnec t Sup ervision - In: no
nDisc onnec t Sup ervision - Out: (Selec tion is c ustomers 
choice.)
nSend  Answer Sup ervision: n
nRec eive Answer Sup ervision: n
— Trunk Group  Ad ministration sc reen (Timing ) 
Set the following  timers from the Administrab le Timers sc reen 
d uring ad ministration of eac h trunk g roup . Selec t the following  Tie 
trunk timer values for this c ountry:
nInc oming  Disc onnec t: 300 ms (E&M c ont)
nOutg oing  Disc onnec t: 300 ms (E&M c ont)
nOutg oing  Dial Guard : 400 ms (E&M c ont, d is)
nInc oming  Glare Guard : 800 ms (E&M c ont, d is)
nOutg oing  Glare Guard : 1000 ms (E&M c ont) 
nOutg oing  Glare Guard : 1200 ms (E&M dis)
nOutg oing  Dial Pulse Rate (PPS): 10 p p s
nOutg oing  Rotary Dig it Dial Make: 40 ms