Mitel Sx-100, Sx-200 Attendant Console Guide

							CALL WDRWAtiD (CANCELLING ALL) 
you may be asked to cancel all call 
Forwarding arrangem ents set up by 
.-. 
extensions: 
3 
0 Dial # 
0 Press RELEASE key 
0 ANSWER and DESTINATION lamps 
go 
out 
i 
l Dial *l 
0 ANSWER lamp lights 
l DESTINATION lamp lights 
2 
Destination display shows: 
I 
0 1-i 
0 ATT lamp lit NOTE- If trunk is assigned to a busy 
lamp iumber, then that lamp lights.  
						

							CONFERENCE CALL 
You have been asked to set up a 
conference call (maximum of six 
parties) : 
1 0 Dial the number of the next party in 
the conference. When they answer: 
0 Press CONF key 
0 CONF lamp lights 
@ANSWER lamp lit 
0 DESTINATION lamp lit 
2 Destination display shows: 
0 t (conference) 
0 You are connected to the calling 
party 
3 0 All parties hear a short burst of 
tone indicating that you and the 
called party are connected to the 
conference 
4 0 Press RELEASE key 
0 CONF lamp lit 
0 ANSWER lamp goes out 
0 DESTINATION lamp goes out 
l Destination display clears 
0 You are disconnected from the 
conference 
5 @To add additional parties to the 
conference, repeat Steps 1, 2, 3 
and 4. 
The CONF lamp remains lit for as long 
as the conference is in use. You may 
enter the conference at any time by 
pressing the CONF key.  
						

							CONFERENCE RECALL 
(ANSWERING RECALL) 
You have set up a conference, and one After speaking with the conference: 
of the parties in the conference wishes 
to recall you (by flashing the 
4 0 Press RELEASE key 
switchhook). 0 CONF lamp lit 
0 ANSWER lamp goes out 
0 Destination display clears 
4 0 CONF lamp flashes 0 You are disconnected from the 
conference 
2 0 Press CONF key 
l CONF lamp lights 
l ANSWER lamp lights 5 l To add additional parties to the 
conference, see page B8 
l AII parties in the conference hear a 
short tone 
0 You are connected to the 
conference 
3 Destination display shows: 
0 L (conference)  
						

							I i 
1. 
DATE DISPLAY 
Destination display shows: 
1 l press and hold IDENT key 4 0 Internal software code and console 
number 
2 
Time display shows: 
0 Month, day and year 
3 
Source display shows: 
0 Generic issue number 5 0 Release IDENT key 
l Time display returns 
l Source and Destination displays 
clear  
						

							DIRECT INWARD SYSTEM 
. 
ACCESS (DISA) 
1 
0 Dial >1
						

							DO NOT DlsTURB (SETTING up) 
To set up: 
3 0 Press RELEASE key 
you are connected to a Destination - 0 All displays clear 
1 
0 Busy lamp field shows extension 
Destination display shows: 
l Extension number busy 
0 Class of service 
0 ATT lamp lit 
2 
e Press DO NOT DSTB key 
0 DO NOT DSTB lamp lights 
l Busy lamp field shows aXtenSiOn 
busy  
						

							DO NOT DISTURB (CANCELLING) 
To cancel: 
You are connected to a Source - 
3 0 Press RELEASE key 
0 All displays clear 
1 Source display shows: 
0 Extension number 
0 Class of service 
0 ATT lamp lit 
2 0 DO NOT DSTB lamp lit 
0 Press DO NOT DSTB key 
0 DO NOT DSTB lamp goes out 
B14  
						

							EXTENSION OUT OF SERVICE 
If you have been asked to take an 
extension out of service temporarily: 
I 0 Dial >(k 
3 Destination display shows: 
0 Number dialed and I- 
l ATT lamp lit 
4 0 Press RELEASE key 
0 Destination display 
clears 
0 DESTINATION and ANSWER lamps 
go out 
0 Extension busy lamp lights 
Extension is now out of service. 
If you dial an extension that has been 
taken out of service, the Destination 
display will show a Class of Service of 
00, and the ERR lamp will light. 
:-‘:-.‘. 
L. . .-I 
,~ . . . . . . . . . 
- _ 
-, . 
“. . . _ 
..__.__ 
, 2--..- 
.’  
						

							RESTORING EXTENSION SERVICE 
To restore an extension to service: 
1 0 Dial *I2 
0 DESTINATION and ANSWER lamps 
light 
2 0 Dial the required extension number 
0 Dial # 
3 Destination display shows: 
0 Number dialed and -I 
0 ATT lamp lit 
4 0 Press RELEASE key 
0 Destination display clears 
0 DESTINATION and ANSWER lamps 
go out 
0 Extension busy lamp goes out 
Extension is restored to service 
If you dial an extension that has been 
taken out of service, the Destination 
display will show a Class of Service of 
00, and the ERR lamp will light.